Mercedes-Benz Sprinter T1N (2002–2006): The Complete Fitment Guide
Share
The Mercedes-Benz Sprinter T1N is the first-generation Sprinter sold in the U.S., badged Freightliner and then Dodge, and it is its own accessory platform. This guide covers what "T1N" means in a listing, the three wheelbases and two roofs, the roof gutters that racks mount to, the rear doors and windows, where these vans rust, and how each accessory category depends on those details.
- Covers Sprinter T1N, 2002 to 2006
- Not covered NCV3 and VS30 (separate guides)
- Sources 30, including owner reports
- Last checked Oct 2026
Quick answer
- Treat the T1N as its own lane. It was sold as a Freightliner and a Dodge, and it uses 118, 140, and 158-inch wheelbases instead of the 144 and 170 of later vans. A part listed only for "Sprinter" needs a year check before you order.18
- Wheelbase and roof height set most fitment. The 158 came only as a high roof. The 118 and 140 came in low and high.8
- Racks use the roof gutters, and the roof seams matter. Owners describe gutter troughs about 65 and a quarter inches apart on a high top, and they report leaking, rusting roof seams on many vans. Check the seams before you bolt anything to the roof.131112
- We could not find a T1N roof-load rating. The 330 lb figure quoted for later Sprinters is not a T1N number. Ask the rack maker and read your owner's manual before you load the roof.27
- Rear doors are a variable. Dodge advertised 270-degree rear doors on the 140 and 158, and a review summary says the 118 had 180. Confirm what your van has before you buy door-mounted gear.1530
- The accessory catalog is small. Fewer brands build for the T1N than for newer Sprinters, so some categories have a handful of options or none.2220
What "T1N" means in a listing
"T1N" is owners' shorthand for the first-generation Sprinter, not a name Mercedes put on the van. It covers model years 2002 to 2006. Mercedes' own rescue-card portal groups these vans under the Sprinter type numbers 901 to 905, a separate set from the 906 series that came after.6
In the U.S. the van wore two badges. Freightliner filed the Sprinter with NHTSA for the 2002 model year, and DaimlerChrysler filed a Dodge make designation for it in August 2002. From model year 2003 the same van was sold as both a Dodge and a Freightliner, and both badges share one VIN coding table.231 For shopping, that means a "Dodge Sprinter," a "Freightliner Sprinter," and a "T1N" are one platform. Search by generation and configuration, not by the badge on the grille.
| Name in a listing | What it means for fitment |
|---|---|
| Sprinter T1N, 2002 to 2006 | This guide. Brands that write the full range usually cover every year in it. |
| Dodge Sprinter, Freightliner Sprinter | The same generation under a different badge. Freightliner for 2002, then both badges from 2003.21 |
| Sprinter 2003 to 2006 | Still T1N, but a seller who stops at 2003 may be leaving out the 2002 model year. Ask whether 2002 is covered.22 |
| Sprinter 2002 and newer, "2002-Current" | Ambiguous. A few universal products use this wording across every generation. Check for a wheelbase or door note.26 |
| Sprinter 2007 and newer | Not T1N. The NCV3 and VS30 use a different body and wheelbases. See the NCV3 guide and the VS30 guide.6 |

Wheelbases and roof heights
This is where T1N owners get tripped up. The T1N does not use the 144 and 170-inch names. It came in three wheelbases, 118, 140, and 158 inches, and two roof heights.89 The 158 was only built as a high roof, so there is no 158 low-roof van to find parts for.8
| Wheelbase | Roof | Overall length | Overall height | Cargo length |
|---|---|---|---|---|
| 118 in | Low | 197 in | 93 in | 99 in |
| 118 in | High | 197 in | 102 in | 99 in |
| 140 in | Low | 225 in | 95 in | 128 in |
| 140 in | High | 225 in | 104 in | 128 in |
| 158 in | High only | 263 in | 104 in | 166 in |
The figures come from a van-builder's specification table. A separate parts supplier's table, measured on passenger vans at curb weight, gives the same lengths but slightly different heights: 93.1 inches for the 118, 102 for the 140 high roof, and 103.6 for the 158.87 Treat height as accurate to about an inch. If a rack, fan, or box brings you close to a clearance limit, measure your own van.
- 118 low roof93 in
- 118 high roof102 in
- 140 low roof95 in
- 140 high roof104 in
- 158 high roof104 in
Full Sprint T1N specification table (search-result excerpt), 2500 models. Bars are height divided by the tallest value, 104 in. Source 8.
| Roof | 118 in | 140 in | 158 in |
|---|---|---|---|
| Low roof | Built | Built | Not built |
| High roof | Built | Built | Built |
| Overall length | 197 in | 225 in | 263 in |
Because of this grid, listings carry two or three tags: wheelbase, roof, and often "2500" or "3500." A roof rack for a 140 high roof is not a rack for a 140 low roof. A rear-door ladder for a high roof is not the right length for a low roof. The Sprinter roof racks guide and the ladders guide explain how each style depends on these fields.
Weight classes, engine, and drive
2500 and 3500
Dodge's 2006 specification sheet lists three gross vehicle weight ratings: 8,550 lb, 9,990 lb, and 10,200 lb. The owner-compiled table pairs 8,550 lb with the 2500 and 9,990 lb with the 3500, and shows the 3500 only on the 140 and 158 high roofs.288 Dodge's feature list makes dual rear wheels standard on the 3500 cargo van and chassis cab.29 Payload falls as the body gets longer. The parts supplier's passenger-van figures run from about 3,681 lb on the 118 down to about 2,846 lb on the 158 high roof.7 That matters for accessories because every rack, bumper, and box comes out of that payload.
Wheels differ by wheelbase too. On the 8,550 lb vans, Dodge lists 15-inch steel wheels on the 118 and 16-inch steel wheels on the 140 and 158.2829 Dual rear wheels also change what fits near the rear wheel wells, such as steps and mud-guard parts, so tell the brand which you have.
Engine
The Dodge brochure lists a 2.7-liter inline-five turbodiesel making 154 hp at 3,800 rpm and 243 lb-ft of torque between 1,600 and 2,400 rpm.15 Dodge lists a five-speed automatic as standard.29 NHTSA filings show an engine-code split within the run. The 2002 filing names a Freightliner engine code, the 2004 filing lists a 45-state OM647 alongside the OM612, and the 2005 filing lists the 50-state OM647 only.245 For bolt-on accessories the engine split rarely matters. It matters for engine service parts and emissions rules.
Drive
Every configuration in the specification table we checked is rear-wheel drive, and a review summary lists rear-wheel drive for the 2006 trims.830 We did not find a factory four-wheel-drive T1N listed. If your van is a 4x4, it was converted, so ask the accessory brand whether the lifted ride height changes step, bumper, or skid plate fitment. The NCV3 guide covers the factory 4x4 that came later.
The roof: gutters, seams, and the load rating
Gutters, not factory rails
Newer Sprinters offered factory roof rails that many racks bolt to. The T1N roof is different. Owners talk about "troughs" or gutters along each side, and one owner measured the leg-to-leg spacing at about 65 and a quarter inches on center on a high top, confirming it by sighting along the troughs from the rear bumper (an owner post, taken from a search excerpt).13 One retailer guide says a direct-mount rack that clamps to the rain gutters is a T1N-only design.19
The practical result is that T1N racks are their own products. A maker that sells racks for the T1N lists separate versions for the 118, 140, and 158 wheelbases.20 That brand's design page lists T1N as a custom design package separate from its 2007-and-newer package.21 A rack for the newer van's rails will not match a T1N roof. The Sprinter roof racks index lists the brands in the WNDR Built catalog with their generation notes.

Roof seams are the weak point
A knowledge-base page that compiles T1N forum threads says roof-seam rust and leaks are "extremely common and well-documented," and points to the transverse seam about three quarters of the way back, where the rear roof panel joins the front section.11 It says North American T1Ns did not get the two-stage seam sealing that other markets got. That is a compiled summary, so read it as a pointer to what owners report, not a manufacturer statement.11
An owner on Sprinter-Source reported leaks at every seam where roof panels meet since the day they bought the van, and replies split on the fix: weld the seam shut and fill it, or use a flexible sealant.12 An Airstream-forum owner who read the T1N rust threads says many owners are patching holes, not sanding surface rust (search excerpt).14 Either way, a rack that sits over or beside a failing seam is a bad bet. Fix the seam first, and ask the rack maker how its feet avoid the seam line.
The load rating is unknown
Until you have a figure, plan for the rack's own weight to count against the roof limit, as it does on later vans. The roof racks guide shows how to do that math with any rating.
Doors, openings, and windows
Rear doors
The Dodge brochure says the rear doors open "a full 270 degrees" on 140 and 158-inch models and stay open with magnets on the exterior panels. Its option list shows plain rear-hinged doors and a 270-degree option as separate rows.15 A Cars.com model summary puts it plainly: 270 degrees on the 140 and 158, against 180 degrees on the 118 (search excerpt).30 So the 118 is the odd one out, and a door-mounted part built for 270-degree doors cannot assume it. The owner-reported record is mixed: a Sprinter-Source thread on door gaps shows owners comparing hinges that look different, and one reply says T1N rear-door trouble is discussed more than the NCV3's (search excerpt).16 Another owner mentions a Mercedes door check strap from a T1N that limits a door to 90 degrees (search excerpt).17
What this means for gear: rear-door ladders, tire carriers, and cargo racks load the hinges and set how far the door can swing. Ask each brand which wheelbase and hinge type it designed for, and whether you need a door stop. The rear door racks guide and the tire carriers guide explain the load path.
Openings
On the parts supplier's passenger-van table, the rear door opening is 61.4 inches wide and the sliding door opening is 41.1 inches wide, on all three wheelbases. Rear load height is 26 inches on the 118 and 28 inches on the 140 and 158.7 Those numbers set what fits behind a rear step or inside a screen frame.
Windows vary by van
Dodge sold the van with window groups. Group I added rear door windows with a defroster. Group II added a fixed window on the right sliding door. Group III added a fixed left-side front window. Group IV added fixed center left and right windows, and 158-inch vans also got rear left and right fixed windows.15 Dodge also listed fixed roof windows as an option, two on the 158.29 A used cargo van may have none of these, and a conversion may have cut new windows. That is why shade makers ask you to pick the window rather than the van. One brand's page says to "choose the appropriate option for your stock or aftermarket window."24 The window covers guide and the window covers index show how fit, magnets, and insulation differ.
Body and underbody rust
A T1N is now at least two decades old, and its rust pattern decides whether an accessory has a sound place to attach. One T1N-focused buyer's guide (it carries affiliate links, so we use it only for inspection points) says rust "kills more T1Ns than any mechanical failure," and lists where to look: the rear wheel arches, the rocker panels and sliding-door step wells, the lower door edges, especially the rear doors where drain holes clog, the frame rails near the rear shackle mounts, and the area under the windshield cowl.10
Each of those spots lines up with an accessory. Steps and running boards bolt near the rockers. Rear bumpers and hitch parts sit near the shackle mounts. Rear-door ladders and carriers bolt to the doors and their lower edges. A moderator note on Sprinter-Source warns that the rear spring mounts can rust away and should be inspected, and mentions a weld-in hanger part listed for 2003 to 2006 Dodge Sprinter 2500s (search excerpt).18 Bolt-on gear is only as good as the metal it bolts to. Read the side steps and bumpers guides with that in mind, and look under the van before you drill.
Fitment by accessory category
This is how each category depends on the fields above. The WNDR Built index lists few T1N-specific products today (see the examples below), so use this as a question list for brands, not as a promise that a part exists.
- Roof racks and ladder racks. Driven by the gutter spacing, wheelbase, and roof height. Brands build separate T1N versions for 118, 140, and 158.20 Read the roof racks guide, then browse the Sprinter roof racks collection.
- Ladders. Rear-door ladders are cut for the door shape and roof height. A retailer lists a rear-door ladder for the T1N in low or high roof versions (search excerpt).25 See the ladders guide and the ladders index.
- Rear-door racks and tire carriers. Driven by hinge type, door swing, and rear wheel choice. Many carriers sold today target newer hinges, so confirm T1N support. See the rear door racks guide and the tire carriers guide.
- Bug screens. Driven by the door opening and roof height. One brand makes a T1N sliding-door screen for the high roof and states that rear screens are not available for the T1N.22 See the bug screens guide.
- Window covers. Driven by which windows your van has. See the window covers guide.
- Bumpers and steps. Driven by the T1N front end and rear frame, and by rust condition. Many bumpers sold for "Sprinter" target the newer vans. See the bumpers guide and the side steps guide.
- Suspension and skid plates. Driven by the T1N's own geometry and drive. Expect to confirm fitment with the brand.
- Awnings and roof fans. These mount to the roof or rack, so they inherit the roof-seam and load questions.
Browse everything the index holds for this family on the Sprinter parts page or the Sprinter collection. If you also run a newer Sprinter, the NCV3 guide and VS30 guide cover those generations.
Common problems owners report
These come from owner posts, brand pages, and compiled guides. Forum posts are individual owner reports, not studies.
The roof seams leak and rust
The T1N's transverse roof seams are a repeated owner complaint. A compiled guide says the seam about three quarters of the way back is a common place for water and rust to start, and warns that rust can eat through to the roof ribs if it is left alone.11 A Sprinter-Source owner reported leaks at all roof seams from day one and years of temporary fixes.12 Rack mounting adds more penetrations or pressure points near the same area.
What to look for: Inspect the seams from inside and outside before you order. Prefer gutter-clamp or documented no-drill mounts, and ask where the feet sit relative to each seam.
The wrong sealant makes the next repair harder
The compiled guide says not to use silicone on a T1N roof. It contaminates the surface so nothing bonds to it later, and some types release an acid that speeds rust under the seal.11 Owners also disagree on whether to weld and fill the seam or use a flexible sealant, and one warns that bonding metal strips on top of a seam gives water a place to sit.12
What to look for: Ask the rack and fan makers which sealant they specify. Do not seal around a mounting point with silicone, and fix rust before you add anything to the roof.
Rust at arches, sills, and door edges undermines bolt-on gear
The T1N buyer's guide ranks rust as the top issue and lists the rear wheel arches, rockers, lower door edges, rear shackle area, and cowl as places to check first.10 A step, ladder, or carrier is only as sound as the panel it bolts to.
What to look for: Look under rubber mats and behind trim where the part will mount. Ask the brand for backing plates or through-bolt hardware instead of self-tapping screws in thin, old metal.
Few brands build for the T1N, and some products don't exist
A T1N sliding-door bug screen exists, but its maker states that rear screens are not available for this older van.22 One rack seller introduces its T1N racks as a product the community asked for, which tells you how long that gap was.20 The WNDR Built index itself lists only three T1N-specific products today.
What to look for: Ask custom shops and fabricators, and compare their wheelbase and roof coverage. Do not assume a rear-door product built for a newer van can be adapted.
Rear-door swing and hinges vary, so door-mounted gear can bind
Dodge advertised 270-degree rear doors on the 140 and 158, and a review summary says the 118 swings 180.1530 Owners on Sprinter-Source compare hinges that look different and report gap and wobble issues (search excerpts).16 Door-mounted gear changes how far a door can swing and where the load goes.
What to look for: Ask the brand which wheelbase and hinge type its rear-door part was built around, whether it needs a stop, and how much swing it leaves.
Rear spring mounts can rust away
A moderator note on a Sprinter-Source suspension thread warns that the rear spring mounts can rust through and should be inspected closely (search excerpt).18 That is the same area where rear bumpers, hitches, and heavy rear-door loads put stress.
What to look for: Inspect the rear frame and spring hangers before adding weight at the back, and ask a bumper maker how its mount ties into the frame.
Fitment terms explained
- T1N
- Owners' name for the 2002 to 2006 Sprinter. It is not a manufacturer name, and parts for it do not carry over to the 2007 and newer vans.6
- Wheelbase (118, 140, 158)
- The distance between the axles in inches. It sets body length, which sets rack length, ladder reach, and where a bumper or step ties in.8
- High roof and low roof
- The two body heights. The 158 was only a high roof. Interior height was about 64 inches on the low roof and 73 on the high.915
- 2500 and 3500
- Weight classes. They change gross weight rating and payload, and they may change rear wheels.8
- Gutter or trough
- The channel along each roof edge that T1N racks clamp to or ride on. It replaces the factory roof rail on later vans.1319
- On center
- The spacing measured from the middle of one mount to the middle of the other. The owner-reported gutter figure is 65 and a quarter inches on center.13
- Rear-hinged 270
- Rear doors that fold back to the side of the van. Dodge lists it as an option on the 140 and 158.15
- Window group
- A Dodge option bundle that added rear, sliding-door, and side windows. It tells you which shades or screens a van needs.15
- Dynamic and static load
- Dynamic is weight on the roof while driving. Static is weight while parked. We could not find a T1N figure for either, so do not borrow one from a newer van.27
Before-you-order checklist
- Confirm the year and badge. A 2002 is a Freightliner. 2003 to 2006 vans are Dodge or Freightliner. Make sure the listing covers your model year.21
- Write down wheelbase and roof. One of 118, 140, or 158, and low or high. Measure if you are unsure; the length is the easiest tell.8
- Note 2500 or 3500, and the rear wheels. Check the door-jamb sticker and the rear axle. Dodge made dual rear wheels standard on 3500 cargo vans, so tell the brand which you have.29
- Check your windows and rear doors. Count the windows, and note the hinge type and how far the doors open.15
- Inspect the roof seams and gutters. Look for cracked sealant, rust staining, and bubbles, inside and out, before a rack goes on.11
- Inspect the metal you will bolt to. Check arches, sills, door bottoms, and the rear frame.10
- Get the roof-load answer in writing. Ask the rack maker for the design load, and read your manual's roof-load entry.27
- Confirm the application list. Match your van to the brand's list of years, wheelbases, and roofs. Ask before you order, not after you drill.
Questions to ask the brand
Ask before you order
- Is this part built for the 2002 to 2006 Sprinter, and does that include 2002 Freightliner vans?
- Which wheelbases (118, 140, 158) and roof heights does it fit, and is there a separate part for each?
- How does it mount to the T1N roof: gutter clamp, through-bolt, or rivet nut, and where do the feet sit relative to the roof seams?
- What roof load do you design the rack to, and does that include the rack's own weight?
- Which sealant and gasket material do you specify around any mounting point?
- For door-mounted parts: which hinge type is it designed for, does it need a door stop, and how far can the door swing?
- Does it work with dual rear wheels, and with a converted four-wheel-drive van?
- What is the warranty, and is it affected by rust or by an earlier repair on the panel?
Examples in the WNDR Built index
These are examples of fitment features, not recommendations. Each shows one thing from this guide. Details come from the brand's own pages as of October 2026. They are the T1N-specific products the index holds today.
Example: a screen built around the sliding-door opening
The Bug Wall T1N Sliding Door Insect Screen (2003 to 2006)
- High roof
- No rear screen for T1N
The brand offers magnet or zipper closures and a choice of where the opening sits, and says rear screens are not available for this older Sprinter. A clear example of the T1N's smaller catalog.22
Example: a shade that attaches without drilling
VanMade Gear T1N Slider Door Shade (2002 to 2006)
- Magnetic, no drilling
- Insulated core
The brand says it attaches magnetically with no drilling and folds so the door still opens and closes.23
Example: a shade you pick by window
VanMade Gear Crew Window Shade, Driver Side 1st Row (2002 to 2006)
- Stock or aftermarket window option
- Confirm the window position
The brand tells buyers to choose the option that matches their stock or aftermarket window, which fits the window-group variation Dodge sold.2415
Key takeaways
- The T1N is the 2002 to 2006 Sprinter, sold as a Freightliner and a Dodge. Parts for the 2007 and newer vans are a different lane.16
- Fitment turns on wheelbase (118, 140, 158), roof height, and, for door parts, hinge type.815
- Racks use the roof gutters. Roof seams and body rust are the first things to inspect.1110
- No T1N roof-load figure was found. Do not borrow the 330 lb number from later vans.27
- The catalog is small. Ask custom shops and confirm every application list.20
Frequently asked questions
Is a Dodge Sprinter the same as a Freightliner Sprinter?
For accessory purposes, yes. NHTSA filings show the van was filed as a Freightliner for 2002 and sold under both badges from 2003, with one shared VIN coding table.231
What wheelbases and roofs did the T1N come in?
118, 140, and 158 inches. The 118 and 140 came in low and high roof, and the 158 only in high roof.8
Will NCV3 or VS30 parts fit my T1N?
Generally not. The wheelbases, body, and roof mounting differ, so racks, ladders, and door gear are not interchangeable. See the NCV3 guide and the VS30 guide.86
How much weight can a T1N roof carry?
We did not find a published T1N roof-load figure, so we do not state one. Read the roof-load entry in your owner's manual and ask the rack maker what it designs to.27
Do T1N rear doors open 270 degrees?
Dodge's 2006 brochure advertises 270-degree doors on the 140 and 158, and a Cars.com summary says the 118 opens 180 degrees. Owners also report differing hinges, so check your own van.153016
What engine does the T1N have?
A 2.7-liter inline-five turbodiesel rated at 154 hp and 243 lb-ft in Dodge's brochure. NHTSA filings show OM612 and OM647 engine codes across the run.1545
Where does a T1N rust?
Owners and one buyer's guide point to the roof seams, rear wheel arches, rockers, lower door edges, rear frame near the shackle mounts, and the cowl. Inspect these before you bolt gear on.1011
Where can I find T1N-specific accessories?
Start with the Sprinter parts page and the category guides linked above, then ask custom fabricators. The index lists a small number today.
Keep planning your build
- Fitment guide Sprinter NCV3 (2007 to 2018) The generation that replaced the T1N, with its own wheelbases and roof limits.
- Fitment guide Sprinter VS30 (2019 and newer) The newest Sprinter, and why its parts do not match the T1N.
- Buyer's guide Sprinter roof racks How rack styles mount and how to plan roof weight.
- Buyer's guide Sprinter rear door racks Hinge load, door swing, and what to ask before you order.
- Buyer's guide Sprinter bug screens Sliding-door and rear-door screens, and how openings differ.
- Buyer's guide Sprinter window covers Pick shades by window, and compare fit and insulation.
Sources
- DaimlerChrysler AG — VIN Coding Summary, Sprinter Vans Built For MY 2003 and Later (NHTSA filing) checked Oct 2026
- Freightliner Corporation — VIN Summary, Freightliner Sprinter (NHTSA filing) checked Oct 2026
- DaimlerChrysler Vans LLC — Revised WMI Make/Model Designation for Sprinter Van (NHTSA filing) checked Oct 2026
- DaimlerChrysler Manufacturing International — Sprinter Vans Built For MY 2004 and Later (NHTSA filing) checked Oct 2026
- DaimlerChrysler Manufacturing International — MY2005 Sprinter VIN Coding Summary (NHTSA filing) checked Oct 2026
- Mercedes-Benz — Rescue card portal, Sprinter type 905 checked Oct 2026
- T1NParts — T1N 2002-2006 Dodge Sprinter Van Dimensions and Capacities (parts supplier) checked Oct 2026
- Full Sprint — T1N Sprinter Van Dimensions and Specifications (owner-compiled, search-result excerpt) checked Oct 2026
- T1NWorld — T1N Sprinter Roofs and Wheelbases (search-result excerpt) checked Oct 2026
- T1NWorld — T1N Sprinter Problems & Fixes: Complete Buyer's Guide (blog with affiliate links) checked Oct 2026
- MyT1N — Roof Seam Rust and Leaks (knowledge base compiled from forum posts) checked Oct 2026
- Sprinter-Source — Roof Rust Nightmare. Repairing seams once and for all (owner reports) checked Oct 2026
- Sprinter-Source — T1N Measurements, Interior/Exterior (owner reports; gutter spacing from a search-result excerpt) checked Oct 2026
- Airstream Forums — Roof redux: Fixing T1N seam rust (owner reports, search-result excerpt) checked Oct 2026
- Dodge — 2006 Sprinter brochure (hosted copy, search-result excerpt) checked Oct 2026
- Sprinter-Source — Rear Door Gap (owner reports, search-result excerpt) checked Oct 2026
- Sprinter-Source — Solution needed for 270 degree hinges, cargo system (owner reports, search-result excerpt) checked Oct 2026
- Sprinter-Source — Suspension Mounts Superficial Rust (moderator note, search-result excerpt) checked Oct 2026
- DVA Mechanics — Sprinter Crossbar Guide (retailer blog, search-result excerpt) checked Oct 2026
- Million Mile Sprinter — T1N Roof Rack (140" WB), Camel Roof Racks checked Oct 2026
- Camel Roof Racks — T1N Roof Rack Custom Design Package (search-result excerpt) checked Oct 2026
- The Bug Wall — 03-06 T1N Mercedes Sprinter Sliding Door Insect Bug Screen checked Oct 2026
- VanMade Gear — Sprinter 2002-2006 Slider Door Shade checked Oct 2026
- VanMade Gear — Sprinter 2002-2006 Crew Window Shade (Driver's Side, 1st Row) checked Oct 2026
- SprinterStore — Sprinter Van Ladders (retailer, search-result excerpt) checked Oct 2026
- Sprinter Parts Depot — T1N: Roof Racks, Ladders & Cargo (retailer, search-result excerpt) checked Oct 2026
- Dodge — 2006 Sprinter Owner's Manual (PDF hosted by Sprinter-RV.com; downloaded, text not read this run) checked Oct 2026
- Dodge Brand Product Information — 2006 Dodge Sprinter specifications (search-result excerpt) checked Oct 2026
- Dodge — 2006 Dodge Sprinter Van Feature Availability (search-result excerpt) checked Oct 2026
- Cars.com — 2006 Dodge Sprinter model summary (search-result excerpt) checked Oct 2026
Fitment and availability change. Confirm compatibility with the brand's application list for your exact van before you buy. Some sources were seen only as search-result excerpts and are labeled that way. The NHTSA filings are scanned documents carried over from an earlier review.
