Sprinter Bumpers: Front and Rear Buyer's Guide
Share
A Sprinter's factory bumpers are plastic covers over a lot of sensors. Aftermarket front and rear bumpers add recovery points, a winch mount, a step or a swing-out carrier, and every one of those changes touches radar, airflow or the hitch. This guide explains how Sprinter bumpers work, what to check before you order, and what owners and makers say goes wrong.
- Fits Sprinter NCV3 and VS30
- Covers Front winch bumpers, rear bumpers, hitch steps
- Sources 35, including owner reports
- Last checked Oct 2026
Quick answer
- Start with your sensors. A 2019+ Sprinter carries a forward radar and six parking sensors in the front bumper and two blind-spot radars and six parking sensors at the rear. Mercedes tells upfitters not to put equipment in front of them.12
- Check the 2025 options. Some 2025 vans have a Sideguard Assist radar in the front corner or blind-spot radars at the rear. At least one maker's bumper does not fit vans that have them.1624
- Ask what the bumper blocks. One maker says its front bumper stops the headlight washers working. Several say a winch will need its solenoid moved.1113
- Count the weight. Published front bumper weights run from 65 lb to 149 lb before the winch. Weight sits ahead of the front axle and comes out of your payload.121625
- For rear steps, check the hitch. Several hitch-mounted steps only fit the factory receiver.2223
- Match the generation. Bumpers for 2014 to 2018 vans do not fit 2019 and later vans.28 The WNDR Built index lists no bumper for the T1N.
What a bumper has to do
The factory Sprinter bumper is a plastic cover, and it is built around sensors. Mercedes lists, for a 2019+ van, one radar in the front bumper for Active Brake Assist and Active Distance Assist, six ultrasonic parking sensors at the front, six at the rear, and two blind-spot radars behind the rear bumper corners.24 Mercedes also describes the front radar as sitting behind the air-inlet grille in the bumper, working with the parking sensors and the windshield camera.2
That is why a Sprinter bumper is a bigger decision than the same part on an older van. A bumper that does the job you bought it for (a winch, a step, recovery points, protection for the radiator and diesel exhaust fluid tank) still has to leave those systems working. The WNDR Built index separates two jobs, and most of the confusion in this category comes from mixing them up:
Front: protect and recover
- Metal structure behind or replacing the plastic cover
- Winch cradle and rated recovery points, because the maker of one winch bumper notes the factory tow hooks are not meant for serious recovery loads9
- Often lighting, a bull bar or a front receiver
- Has to clear the radar, parking sensors, camera and cooling air
Rear: step, carry, tow
- A step on the hitch, a full replacement bumper, or a swing-arm system
- Often carries the hitch receiver, a spare tire or a box
- Has to clear the rear doors, the exhaust and the blind-spot and parking sensors
- Adds weight behind the rear axle
How Sprinter bumpers work
Front bumpers
Most aftermarket front bumpers use one of three layouts. In the first, a metal structure replaces most of the plastic cover and the winch cradle bolts to the frame. In the second, a smaller winch mount or bull bar sits behind a trimmed factory cover, which stays on the van. In the third, a hybrid uses a steel winch cradle with an aluminum outer shell, so the strong part sits where the load is and the rest stays light.9161821
Makers describe the load path the same way: the winch pulls on the cradle, the cradle spreads the load into the chassis, and the bumper body is mostly armor and a mounting surface for lights and recovery shackles.918 Winch size limits depend on the cradle. One maker lists its winch fit by physical dimensions, and another by a winch rating of up to 13,500 lb.918

Rear bumpers and steps
Rear products fall into three styles, and they are not interchangeable:
| Style | What it is | What to check first |
|---|---|---|
| Hitch-mounted step | A step plate that bolts to the hitch receiver below the factory bumper.2223 | Whether you have the factory hitch. Two makers say their steps need it.2223 |
| Full replacement bumper | Replaces the factory rear bumper with an aluminum or steel unit, often with a step and light pockets.17 | Sensor cut-outs, exhaust clearance and dually exclusions.17 |
| Swing-arm system | A bumper with a hitch and arms that swing out so a tire or box can carry gear without blocking the doors.1431 | Arm and tongue weight limits, and how the arm latches to the door.1415 |
A swing-arm system is the closest relative of the products in the tire carrier, rear door rack guides, so read those if you plan to carry a spare or a box.

What to look for
These are the criteria that separate bumpers that work on a modern Sprinter from ones that cause error messages. Each item says why it matters and how to check it.
- Sensor and radar provisions. Mercedes tells upfitters that nothing should be installed in front of the bumper sensors and radar, and that changes to the front radar, its mounting or its surroundings are not permitted.12 The practical check: does the bumper page say how the forward radar and each parking sensor are kept in their original positions? Look for named cut-outs, a radar bracket or bezel, and a statement for your model year.1629
- The 2025 sensor options. The front Sideguard Assist radar (code JT7) sits under the passenger-side front bumper, and the blind-spot radars (code JA7) sit behind the rear bumper corners.1 Some makers carry separate parts or exclude vans that have them. Find your option codes before you order.1624
- Cooling airflow. The 2016 NCV3 body-builder guideline says the grille opening must stay at least 170 in² and the bumper opening at least 109 in².5 Newer guidelines say the temperature sensor in the front bumper must stay put with free air around its tip.1 Owl lists airflow as a common pitfall of poorly designed bumpers.10 Check whether the maker states airflow was designed in, and how.
- Material and weight. Full steel is strongest and heaviest. Full aluminum is lighter. A steel winch cradle under an aluminum body is the hybrid some makers use to hold weight down.916 Ask for the installed weight with and without the winch.
- Winch cradle and fairlead. Check the winch dimensions the cradle accepts, and the line type. One maker's front bumper does not work with roller fairleads or braided steel cable and needs synthetic line with a compatible fairlead.12
- What it blocks. Headlight washers, the diesel exhaust fluid tank, fog lights and the underside of the radiator are all affected by some bumpers.111316
- Mounting and what must be cut. Several front bumpers require trimming the factory plastic cover, and one supplies a template.122129 Ask whether the install is reversible. One winch mount says it can be removed and the factory bumper reinstalled.21
- Drivetrain, option and wheelbase variants. Some bumpers need extra brackets on 2WD or 3500 vans, and one winch mount does not fit vans with the heavy-duty rear air conditioning package.161920
- Rear: hitch compatibility. Some steps and bumpers require the factory hitch, others work with or without it, and one works with similarly shaped aftermarket hitches.222324
- Rear: door clearance and exhaust. Check that the rear doors can open fully, and whether the exhaust needs trimming. One rear bumper says it may need slight trimming of the factory exhaust.17
- Finish and corrosion. Powder coat chips on gear that meets rocks. Ask whether the finish can be touched up and what the warranty says about coating and welds.
- Warranty. Read the maker's terms on installation and on non-factory vehicles. Aluminess's lifetime warranty applies to the original purchaser when the product is installed according to its instructions.35
Specs explained
- Winch rating (for example 12,000 or 13,500 lb)
- The winch's pulling rating, not the bumper's. A bumper "supports" a winch size only if its cradle and frame mounts were designed for that load.918
- Winch cradle
- The structural tray the winch bolts to. Look for steel here, and look at how it attaches to the frame, because the rest of the bumper can be lighter.916
- Solenoid relocation
- Some bumper pages say the winch's contactor box will likely need moving to fit.1113 It adds wiring work, so ask about it.
- Fairlead (roller vs. synthetic)
- The guide that feeds the line onto the drum. Roller fairleads suit steel cable. Synthetic rope uses a smooth fairlead, and some bumpers only accept one type.12
- Bull bar and brush guard
- Tubing in front of the grille and headlights. They protect from impacts, add lighting points, and may sit in front of sensors, so confirm the sensor window.310
- Approach and departure angle
- How steep a slope the front or rear can meet before the bumper touches. Makers describe tapered, tucked-up bumpers as improving both.10 Rear bumpers say whether they keep the factory departure angle.17
- Tongue weight
- The downward force a trailer puts on the hitch. On one swing-arm bumper, the weight of a storage box counts against the tongue weight limit.14
- Swing arm limit
- The maximum load on the arm that swings out. One maker lists 100 lb for a standard arm and 200 lb for a bike-rack arm.14
- Sensor-affecting area
- Parts of the bumper in a radar's or parking sensor's field of view. Mercedes says paint thickness and metallic content change radar performance, and it warns against painting bumpers with ultrasonic sensors fitted.34
- GAWR
- Gross axle weight rating, the most weight the axle is rated for. Mercedes's body-builder guideline says not to exceed GAWR and GVWR, and a front bumper puts its weight ahead of the front axle.5
- Flatline aluminum rear bumperunder 45 lb
- Aluminess Recon front bumper65 lb
- ROAMBUILT Full Guard front bumper149 lb
Brand-published bumper weights, checked Oct 2026. The Flatline figure is "just under 45 pounds", plotted at 45. These are bumpers only, before the winch. Sources 12, 16, 24.
Common problems owners report
These come from Mercedes service bulletins, installation sheets, brand warnings and owner discussions. Where a point comes from a maker rather than an owner, we say so. Where a forum page would not load, we say that too.
Driver-assist warnings after the front end is changed
Mercedes's own service bulletins show how sensitive the forward radar is. One lists a "restricted" Active Brake Assist message, and says that if the radar is not mounted correctly a case with photos should be opened.7 Another ties a calibration fault to the radar's installation height and says to correct the position or recalibrate.6 These bulletins are about factory vans, not aftermarket bumpers. They show the radar tolerates little movement. Makers respond with a bracket or bezel: one winch mount ships a radar mount, and another publishes a radar bezel guide for 2025+ vans.2129
What to look for: a bumper or mount that includes a radar bracket for your model year, and a shop that will verify the radar and sensor functions after the install.
Headlight washers stop working
Aluminess says its front winch bumpers inhibit the headlight washers on the 2007 to 2013 and 2025+ models: the bumper can still be installed, but the washers will be blocked.1113 This is a maker statement, so check each brand's page.
What to look for: a stated "compatibility" section on the bumper page, and the washer question on your ask-the-brand list.
Corner and rear sensors end up blocked or unsupported
A Flatline rear bumper reviewer called it a nice bumper that is not compatible with the JT7 and JA7 blind-spot options (snippet only, the review page did not load for us).24 The maker's fitment note agrees: for 2025+ vans it fits those without JA7 or JT7.24 ROAMBUILT says its Full Guard front bumper is not compatible with a 2025 van that has the Sideguard Assist sensor under the passenger-side headlight.16 Aluminess says sensor holes can be drilled in its rear bumper on request, but back-up sensors will not work.14 Mercedes warns that detachable parts such as steps and brush guards in the detection range can impair Park Assist.3
What to look for: a fitment line that names your option codes, not just the year.
The nose sits lower under a heavy bumper and winch
A suspension seller says extra front weight such as a winch bumper can cause sag and sells helper springs for it.26 That is a vendor claim for a Sprinter. Owners of other vehicles report about a quarter to three-quarters of an inch of front sag after a bumper and winch (a Jeep forum thread, a different vehicle, so treat the numbers as an example only).30 A builder points out that steel bumpers, winches and skid plates all consume payload, and that 4x4 and AWD Sprinters already start with less.25
What to look for: the installed weight, and a plan for the front springs. Weigh the finished van.
Not enough air gets to the radiator and intercooler
Owl calls airflow a common pitfall of poorly designed aftermarket bumpers.10 Mercedes publishes minimum opening areas for the NCV3 and tells builders to keep the front temperature sensor's airflow clear.15 Makers respond with design claims: ram-air tunnels on one, "exceeds Mercedes airflow requirements" on another.1618 We found no independent test of any of them.
What to look for: an airflow statement and, if you tow or climb hot grades, the brand's own temperature data if it has any.
Trimming the plastic cover takes longer than expected
Van Compass's instructions require removing and trimming the plastic cover, and its listing gives a shop labor time of six hours.2021 One reviewer on the maker's site said the cutting needed lots of fitting and removing of the cover (snippet only).33 Aluminess also says its Recon bumper requires cutting the factory cover.12
What to look for: a cutting template, clear instructions, and a shop that has done your model year.
A hitch step that does not fit the hitch you have
Sandy Vans says its step mounts to the factory hitch only, and aftermarket hitches have different dimensions.23 Van Compass's tug step instructions say they cannot guarantee fitment with an aftermarket hitch.22 On 2007 to 2018 vans, Sandy Vans says four holes must be drilled in the factory hitch.23
What to look for: a step that names the hitch it fits, and your hitch's part number checked first.
Swing-arm hardware works loose
A Sportsmobile Forum owner reported the two small bolts holding the tire-carrier latch on an Aluminess swing-out bumper went missing on washboard road, and others said they now check them monthly (a 2009 thread that would not load for us, so snippet only).27 Aluminess's installation sheets say to check the hardware after 100 miles because of vibration, torque the hitch bolts to 63 ft-lb, and keep the arm latched to the door when driving.1535
What to look for: thread-locking or a retaining pin on the latch, a written torque value, and a re-check after the first trip.
The rear bumper does not fit your exact van
ROAMBUILT excludes the 144 in dually and says the exhaust may need trimming.17 Aluminess says its Slimline rear bumper does not fit the 144 in wheelbase dually.14 A front bumper maker says 2WD and 3500 vans need extra brackets.1619
What to look for: your wheelbase, drivetrain and dual-wheel status stated on the page.
Fitment checklist
Do these before you add anything to the cart. Each one comes from a fitment limit that a maker or Mercedes states.
- Generation. NCV3 (2007 to 2018) and VS30 (2019 and later) bumpers are different. A Backwoods-bumper installer says bumpers built for 2014 to 2018 vans do not fit 2019 and later.28 Confirm in the NCV3 or VS30 guide.
- Model year within VS30. Maker pages split 2019 to 2024 from 2025+ because the sensors and front end changed.1124
- Option codes. Check your build sheet for JT7 (Sideguard Assist) and JA7 (blind-spot assist with rear cross traffic alert).1
- Engine and diesel exhaust fluid tank. One maker notes the tank is exposed on vans that have it in the engine compartment (option KP2).13
- Drivetrain and gross weight. 2WD and 3500 vans may need extra brackets, and the WNDR Built index lists them separately where the brand does.1619
- Rear air conditioning. One winch mount does not fit with the heavy-duty rear AC package.20
- Wheelbase and dually. Rear bumpers exclude the 144 in dually.1417
- Hitch. Factory or aftermarket? Steps and bumpers differ in what they accept.2324
- What you already carry. If you run or plan a rear door rack, tire carrier or ladder, check that the rear bumper and those parts do not compete for the same door.
Install and long-term ownership
Time and help
Install times vary a lot by style. A hitch step is the simplest: Sandy Vans lists about an hour, four bolts on 2019 and newer vans, and drilling on 2007 to 2018 vans.23 A front winch bumper is a larger job. An installer's guide to one brand's front bumper says it takes four to six hours for a DIY builder and, at over 130 lb, needs a second person.28 Van Compass lists six hours of shop labor for its winch mount, and Wolf Pack Overland recommends professional installation for the Aluminess Recon.2032
After the install
- Check sensors and camera. Test the parking sensors, cruise and brake assist, and the front camera. One maker lists these checks as a post-install step.9
- Re-torque and re-check. Aluminess's sheet says to check the hardware after 100 miles of driving because of vibration.35
- Keep the sensors clean. Mercedes says dirt, damage or a covered sensor reduces what the driver-assist systems can see.8
- Do not paint over the sensors. Mercedes says to leave sensor covers alone, and not to paint a bumper with ultrasonic sensors installed.34
- Weigh the van. A Mercedes-Benz Van Center payload guide says to weigh the completed van after upfitting and to re-weigh when the upfit or load changes.34
- Plan the rest of the front end. A heavy bumper changes the load on the springs.

Ask the brand before you order
Ask before you order
- Which model years, option codes (JT7, JA7), drivetrains and wheelbases does this exact part fit, and what is excluded?
- How are the forward radar, each parking sensor and the camera kept in their original position, and is a bracket included for my year?
- Do the headlight washers, fog lights and diesel exhaust fluid tank still work or stay protected?
- What is the installed weight, with and without the winch, and what do you suggest for the front springs?
- How does the winch cradle attach to the frame, and which winch sizes and fairlead types does it accept? Does the solenoid need moving?
- Does the install cut the factory cover, and can the van be returned to stock?
- How do you support airflow to the radiator and intercooler, and do you have test data?
- For rear parts: what hitch does it need, what is the tongue weight limit including any box, and does it clear the rear doors and exhaust?
- What does the warranty cover on coating, welds and hardware, and does installing it affect the van's warranty?
Examples in the WNDR Built index
These products each show one feature from this guide. They are examples, not recommendations; the index lists every brand we track.
Example: a lighter front bumper that keeps sensor provisions
Aluminess Recon Front Winch Bumper (Sprinter 2019+)
- 65 lb bumper weight
- Synthetic line and compatible fairlead only
The maker lists a 65 lb bumper, a pre-installed sensor window and parking sensor retainers, and a requirement to cut the factory cover.12
Example: a dedicated 2025+ front bumper
Aluminess Front Winch Bumper (2025+ Sprinter)
- Sideguard Assist compatible
- Headlight washers blocked
Its listing names Side Guard Assist and parking sensor compatibility, and states plainly that the headlight washers will not work.11
Example: hybrid steel cradle with aluminum body
ROAMBUILT Full Guard Front Bumper
- 149 lb
- Check for the Sideguard Assist corner sensor
A steel winch cradle and shackle mounts with an aluminum shell, and a stated airflow claim. The page says it is not compatible with 2025 vans that have the passenger-side Sideguard Assist sensor.16
Example: airflow designed into the front end
Owl Adax Pro Front Bumper
- Ram-air tunnels
- Winch up to 13,500 lb
The listing describes ram-air cooling tunnels, a low-mounted winch position, diesel exhaust fluid tank protection and Sideguard Assist compatibility.18
Example: a front receiver with a stated rating
Owl Pismo Front Bumper
- Front hitch rated 300 lb
- 3500 and 2WD need extra OEM brackets
A retailer listing for this steel bumper gives a 300 lb front hitch rating and notes that 3500 and 2WD vans need extra brackets.19
Example: a step that needs the factory hitch
Sandy Vans Stern Rear Step
- Factory hitch only
- Rear sensors unaffected
Four bolts on 2019 and newer vans, with drilling on 2007 to 2018. The page says it does not affect Mercedes rear proximity sensors.23
Example: a full replacement rear bumper
ROAMBUILT Rear Bumper (2019 to 2024)
- Built-in step
- May need exhaust trimming
The page lists compatibility with parking sensors and blind-spot assist, and excludes the 144 in dually.17
Example: a swing-arm rear system
Aluminess Slimline Rear Bumper with Swing Arms (2019 to 2024)
- 750 lb tongue weight
- Box weight counts against it
The listing gives 100 lb per standard arm, 200 lb on the bike-rack arm, and a 33 in maximum tire.14
- Aluminess standard swing arm100 lb
- Aluminess bike-rack swing arm200 lb
- Owl Pismo front receiver300 lb
- Aluminess NCV3 rear tongue weight300 lb
- Aluminess VS30 rear tongue weight750 lb
Brand-published limits, checked Oct 2026. They measure different things (arm load, front receiver, tongue weight), so compare within a row, not across. Sources 14, 19, 31.
Key takeaways
- A 2019+ Sprinter's bumpers hold its forward radar, blind-spot radars and parking sensors. Choose the bumper by what it leaves working.12
- Match the generation, model year and option codes, not just "Sprinter".162428
- Ask about headlight washers, solenoid location, fairlead type and what must be cut.1112
- Weigh the van after the install. Bumper weight is ahead of the front axle and comes out of payload.25
- For rear steps, confirm the hitch; for swing arms, read the tongue and arm limits.1423
Frequently asked questions
Will an aftermarket bumper void my Sprinter's warranty?
One bumper maker says the bumper alone cannot void your whole warranty, but damage it directly causes, such as sensors harmed by a poor install, might not be covered.9 Mercedes's body-builder guidance is stricter about the radar and airbag areas.2 Ask your dealer before you order.
Do aftermarket bumpers work with adaptive cruise and automatic braking?
Several makers say their bumpers keep those systems working and include radar brackets or windows.162129 Mercedes's service bulletins show the radar is sensitive to position, so ask for a post-install check.67
Do I need a winch bumper if I stay on roads?
Not necessarily. One maker says the factory cover is fine for highway and city driving, and that a winch is the main reason most buyers upgrade.9 If you only want a rear step, a hitch-mounted step is a smaller change.23
Keep planning your build
- Fitment guide Sprinter VS30 (2019+) Model years, roof heights and what changes with the 2025 update.
- Buyer's guide Sprinter tire carriers Swing-out bumpers and door-mounted carriers compared.
- Buyer's guide Ford Transit bumpers The same sensor and fitment questions on the Transit.
- Buyer's guide Ram ProMaster bumpers Front and rear bumpers for the ProMaster.
Sources
- Mercedes-Benz Vans — Body and Equipment Guideline Sprinter BM907, edition 2025-6 (excerpts via search) checked Oct 2026
- Mercedes-Benz Vans — Body and Equipment Guideline Sprinter BM907, edition 2024-9 (excerpts via search) checked Oct 2026
- Mercedes-Benz Vans — Body and Equipment Guideline addendum 07/2022 (excerpts via search) checked Oct 2026
- Mercedes-Benz Vans — Sprinter Painting Over Sensors bulletin, MY2019+ (excerpts via search) checked Oct 2026
- Mercedes-Benz — Sprinter Body Equipment Guidelines 2016 (hosted by sprinter-rv.com, excerpts via search) checked Oct 2026
- NHTSA — Mercedes-Benz TSB LI54.71-N-075673, Distronic and/or Active Brake Assist inoperative checked Oct 2026
- NHTSA — Mercedes-Benz service bulletin, "Active Brake Assist currently restricted" checked Oct 2026
- Mercedes-Benz Vans — Sprinter owner's manual, April 2024 (excerpts via search) checked Oct 2026
- Flatline Van Co. — Buyer's Guide for an Off-Road Sprinter Van Front Bumper checked Oct 2026
- Owl Outdoor — The Complete Guide to Sprinter Van Front Bumpers checked Oct 2026
- Aluminess — Front Winch Bumper, 2025-26 Sprinter (excerpt via search) checked Oct 2026
- Aluminess — Recon Front Winch Bumper, 2019-26 Sprinter (excerpt via search) checked Oct 2026
- Aluminess — Sprinter Front Bumper 2007-2013 (excerpt via search) checked Oct 2026
- Aluminess — Slimline Rear Bumper, 2019-26 Sprinter (excerpt via search) checked Oct 2026
- Aluminess — Rear bumper installation instructions, Sprinter 2007+ Slimline with hitch (excerpt via search) checked Oct 2026
- ROAMBUILT — Mercedes Sprinter Full Guard Front Bumper checked Oct 2026
- ROAMBUILT — Mercedes Sprinter (2019-2024) Rear Bumper checked Oct 2026
- Owl Outdoor — Adax Pro: Front Bumper for Mercedes Sprinter Vans (2019+) checked Oct 2026
- Main Line Overland — Owl Pismo Front Bumper for Mercedes Sprinter Van (retailer listing, excerpt via search) checked Oct 2026
- Van Compass — Front Winch Mount with Bull Bar, Sprinter 2019+ checked Oct 2026
- Van Compass — 4099 Front Winch Mount installation instructions (JEGS-hosted copy, excerpts via search) checked Oct 2026
- Van Compass — 4057/4080 Rear Tug Step installation instructions (retailer-hosted copy, excerpts via search) checked Oct 2026
- Sandy Vans — Sprinter Rear Step for OEM Hitch, The Stern checked Oct 2026
- Flatline Van Co. — Sprinter Rear Bumper (fitment notes and one customer review, excerpts via search) checked Oct 2026
- The Vansmith — 4x4 Sprinter GVWR and Payload (excerpts via search) checked Oct 2026
- Sprinter Upgrades — SumoSprings for Sprinter 4x4 Front (seller listing, excerpt via search) checked Oct 2026
- Sportsmobile Forum — "Speaking of things spinning off....." (2009 owner reports, excerpt via search) checked Oct 2026
- Mango Vans — Backwoods Sprinter Bumper: All Your Questions Answered (installer, excerpts via search) checked Oct 2026
- Flatline Van Co. — Sprinter Front Bumper 2019+ (excerpts via search) checked Oct 2026
- JL Wrangler Forums — Sag when installing bumper and winch on 4XE? (owner reports, different vehicle) checked Oct 2026
- Campervan HQ — Aluminess 2007-2018 Mercedes Sprinter Rear Bumper (excerpt via search) checked Oct 2026
- Wolf Pack Overland — Aluminess Recon Winch Bumper listing (installer, excerpt via search) checked Oct 2026
- Mercedes-Benz Van Center Easton — Sprinter Dimensions, Cargo and Payload Guide (excerpt via search) checked Oct 2026
- Aluminess — Rear bumper installation instructions 210284.1, Sprinter 2007+ Slimline, no swing arms (excerpt via search) checked Oct 2026
- Van Compass — Front Winch Mount customer reviews (excerpt via search) checked Oct 2026
Fitment and options change by model year. Several maker pages could not be opened directly and are cited from search excerpts, as marked. Confirm with the brand before you buy.
