
Aluminess
Front Winch Bumper - 2025-26 Sprinter
Indexed listing. WNDR Built doesn't sell this product; the button opens aluminess.com.
An aluminum bumper with a steel winch cradle
The Aluminess Front Winch Bumper replaces the Sprinter’s factory front bumper with an aluminum bumper supported by a steel winch cradle. The cradle fastens to the frame rails using factory bolts, and the bumper then mounts to the cradle. It provides a front-mounted winch installation with a fairlead cover for installations without a winch.
The design accommodates the van’s front radar, parking sensors and Side Guard Assist through sensor housings, retainers and acrylic windows. The installation guide relocates the existing sensors and routes their wiring into the bumper. Square light openings provide mounting positions for lights, while the maker also lists provision for shackles and a receiver. Full Brush Guard, Bull Bar and No Bull Bar configurations are offered.
Square light openings
The bumper has square light holes for mounting lights.
Fairlead cover
The supplied fairlead cover is installed when a winch is not fitted.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Aluminess
- 2025–2025 Mercedes-Benz Sprinter
- 2025–2025 Mercedes-Benz Sprinter 1500
- 2025–2026 Mercedes-Benz Sprinter 2500
- 2025–2026 Mercedes-Benz Sprinter 3500
- 2025–2026 Mercedes-Benz Sprinter 3500XD
Headlight washers blocked
The bumper can be installed on vans with headlight washers, but blocks the washers from use.
Winch solenoid relocation
Aluminess says winch solenoid relocation will likely be required because winch manufacturers continually change sizes and designs.
Accessories not included
Lights, shackles and a receiver are not included with the standard bumper.
Converted vehicles
Aluminess designs its products for factory-manufactured vehicles; some aftermarket conversions are incompatible. Determine compatibility before purchasing.
Use and vehicle suitability
Aluminess states its products are designed for off-road vehicle use. Installation may exceed the vehicle’s factory-designed capabilities; determine vehicle suitability and check local vehicle codes before purchase.
Factory sensors
Aluminess lists compatibility with front parking sensors, collision assist and Side Guard Assist. The guide transfers the OEM front radar sensor and routes the sensor wiring through the bumper.
Configuration options
Choose With Full Brush Guard, With Bull Bar or No Bull Bar. The maker’s page also offers a separate Parking Sensor Kit selection: None or Qty.
Specs, parts & installation
Construction
| Bumper | Aluminum |
|---|---|
| Winch cradle | Steel |
| Finish | Powder-coated textured Black |
Shipping dimensions
| Height | 36 IN. |
|---|---|
| Width | 48 IN. |
| Depth | 87 IN. |
| Shipping weight | 113 LBS. |
What’s in the box
Bumper and cradle
One bumper in the selected configuration, one steel winch cradle and one fairlead cover.
Sensor mounting components
The installation sheet lists one air temperature sensor bracket, one front radar sensor housing, two Side Guard Assist sensor housings, three acrylic sensor windows and parking sensor retainers.
Fender mounting components
One left and one right fender bracket, plus one left and one right fender liner support bracket.
Installation hardware
Mounting fasteners, anti-seize, thread locker, adhesive zip tie mounts, zip ties and an O-ring are listed in the installation sheet.
Installation at a glance
Installation replaces the stock bumper and crossmember, transfers sensors and reconnects their wiring.
Remove the front camera if applicable; disconnect parking sensor, Side Guard Assist and fog light wiring as applicable. The guide also removes the airflow skirt and OEM fender supports.
Apply anti-seize to stainless bolt threads before assembly. Apply thread locker where the guide specifies, and torque the winch cradle’s factory bolts to OEM specifications.
If fitting a winch, follow its manufacturer’s instructions; otherwise install the fairlead cover.
Keep wiring clear of pinch points and the wheel liner inside the bumper. Reinstall the grille after aligning and securing the bumper.
Verify sensor operation by driving for 15 to 30 minutes. Check bolt tightness after 100 miles, periodically afterwards and after any off-road use.
Tools listed by Aluminess
- Ratchet with extension, sockets and wrenches: 13 MM, 14 MM, 18 MM, 3/8”, 7/16”, 1/2”, 3/4”.
- Torx drivers: T25, T30, T35, T45; hex keys/drivers: 1/8”, 5/32”.
- Torque wrench, Phillips screwdriver, slotted screwdriver and push-pin remover; hammer and small prybar are optional.
Sensor positioning and final alignment
- Reconnect Side Guard Assist wiring before fully tightening its hardware, with the sensor entirely within the acrylic window opening.
- Orient parking sensor retainer tabs in the bumper’s relief cutouts and ensure the tabs are fully extended. Install the sensors with the OEM gasket and secure the harness using the zip ties and adhesive mounts.
- Secure the air temperature sensor in its bracket with the O-ring at the indicated notch before tightening the bracket locknut.
- Step 32 directs alignment around the headlights and fenders by evenly tightening all 1/2” hardware, then torquing to 75 ft-lbs; use caution near the headlights.
Source notes
- Aluminess’s product page offers a separate optional Parking Sensor Kit with None and Qty. selections, without defining its contents; the installation sheet lists parking sensor retainers among included components. This listing follows the sheet.
- The installation sheet’s page 2 lists eight parking sensor retainers; page 7 step 24 installs six retainers, while its pro tip calls the eight included pieces “sensors,” with two extra. The disputed quantity and sensor-content claim are omitted.
- The product title says 2025–26 and the description says 2025+; the FITS table lists 2025–2025 for Sprinter and Sprinter 1500 and 2025–2026 for Sprinter 2500, 3500 and 3500XD. Vehicle fitment above follows those model-specific rows.
Lead Time
Bumpers and roof racks ship by LTL freight and do not qualify for free shipping; destination charges may apply. Inspect and record shipping damage before signing.
Read Aluminess lead time policy on WNDR BuiltWarranty
Lifetime warranty for the original retail purchaser requires correct installation under official instructions; modifications void coverage; exclusions apply, and claim shipping both ways may be customer-paid.
Read Aluminess warranty policy on WNDR BuiltReturns
Authorized nondefective returns within 15 days; custom/special orders excluded; roof racks require another buyer; refunds deduct all shipping, including Aluminess-paid outbound costs, and any restoration costs.
Read Aluminess returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon