Ram ProMaster Side Steps: What's Actually Available
Share
A full-size ProMaster sits high enough that climbing into the cab or through the sliding door is a daily chore, and owners describe bruised shins and worse without a step. This guide explains how ProMaster steps attach, the five styles you will meet, what to check before you order, and what owners report going wrong.
- Fits Full-size Ram ProMaster, 2014 to present
- Covers Side boards, hoop steps, retractable steps, rear steps
- Sources 23, including owner reports
- Last checked Nov 2026
Quick answer
- Wheelbase decides the kit. Listings split by 118, 136, 159 and 159 EXT. One all-steel set is made for the 159 only, retailer listings disagree on whether another maker’s step covers the 118, and Ram’s own sliding-door step is not offered on the 118.12512
- Almost every aftermarket step drills into the body. Makers describe drilling the pinch weld or rocker panel, a two-person job, and a right-angle drill. Plan for hours, not minutes, and ask about rust protection.13922
- Fixed board or retractable step? Fixed boards stick out and one owner removed boards because they did not project far enough to step out comfortably when carrying something, and moved to a slide-out step.16
- Drop and projection are the trade-off. One owner called hoop steps too low for forest roads and broke them off; another measured a 6-inch board at about 13 inches above the ground.14
- Only one maker publishes a load rating we found. Aluminess lists 300 lb. Flatline, Luverne and APS pages we read give none, so ask before you lean a ladder or a bike on a step.216
- Check your side ladder first. At least one ProMaster side ladder maker says its lower mount is blocked by most full-length running boards.20
Why add steps?
The ProMaster is a tall cargo van with a high step-in to the cab and an even higher reach into the side door. One owner who is 5 feet 4 inches tall described using a step stool on a rope to get into a 118 van.14 Another owner who installed hoop steps wrote that they replaced a 17 inch step up with a 9 inch one. Those are single-owner measurements, not a Ram figure, but they match what most threads describe: the first step off the ground is the hard one.18
Owners also tie steps to safety. In one thread an owner reported a shin bruise that lasted months from climbing into another member’s van, and another reported that a member’s spouse broke an ankle. Treat those as anecdotes, but they explain why the question comes up so often for anyone climbing in with gear.14
A step also changes how you use the van day to day. The passenger side needs a long surface that covers the front door and the sliding door, while the driver side usually needs only a short one, which is how Aluminess and Luverne split their kits.48 Before choosing a style, decide who uses the step, whether they step out blind while carrying things, and how much the van can project sideways on narrow roads and trails.
How ProMaster steps work
Most aftermarket ProMaster steps hang from the underside of the body, near the rocker panel and the pinch weld. The pinch weld is the seam where the inner and outer body panels are welded together along the bottom edge of the doors. Makers use it as a mounting point because it is structural. Aluminess describes hanging its step from the back side of the pinch weld and lining its brackets up with “unibody supports on the underside”; CARR drills through the pinch weld and uses spacer tubes sized for the ProMaster.39
Luverne describes its boards as “rocker mount” with vehicle-specific brackets, and sells the board and bracket kit as separate parts.6 One owner describes APS iBoards as aluminum boards whose connectors use holes already in the van plus one drilled hole for a support bracket (search excerpt).17 The mounting style matters because it sets the install work, how much the step can carry and how easily you can undo it later.

What the step does for the body
A step puts a side load on the body, so where the brackets land matters. Aluminess lines its brackets up with unibody supports and CARR spaces its brackets off the pinch weld with tubes sized for the ProMaster.39 Ram published no aftermarket step mounting limits that we could find, so any claim about how much a step can carry comes from the maker, not from Ram.
Some steps combine a step with accessory mounts. Aluminess builds mounting provisions for rock lights and L-Track clips into its Recon step, though the lights and clips are not included.24 If you plan to hang gear from a step, ask what the mount is rated for, not just what the step is rated for.
The five styles
ProMaster step products fall into five groups. They differ in how they attach, how far they project and how much install work they ask for, which matters more than any single spec.
1. Full-length boards
2. Door-zone steps
- Steps cut to the door openings instead of a continuous board, such as a 92 inch passenger step and a 30.75 inch driver step.2
- Flatline describes its set as a lower first step that stays low profile, built from steel tube, steps and braces; its page does not publish step lengths.1
- Ask each brand for the drop, because door-zone steps and boards can differ.
3. Hoop steps
- An individual step at each door, mounted through the pinch weld with spacer tubes sized for the ProMaster.9
- Owners call the front steps fairly easy and the sliding-door step more involved.14
- Placement is adjustable. One owner tucked the steps under the body and marked the edge with tape so it can be found when stepping out.14
4. Retractable steps
5. Factory and rear steps. Ram sells a Mopar sliding-door step, but Ram’s 2026 buyer guide lists it as unavailable on 118-inch vans, and lists the Mopar rear bumper step as unavailable with the Class IV hitch receiver.12 The 2023 front bumper also integrates a step for reaching the windshield, which is a different job from a side step.13 Hitch-mounted rear steps and bumper steps solve rear access, not side entry; see our ProMaster bumpers guide and the rear bumpers guide.
What to look for
Every step on the market asks you to trade drop, projection, install effort and fit. Use this checklist to compare them on the same terms.
- Wheelbase and door coverage. The long passenger piece has to match your wheelbase and the position of the sliding door. Flatline lists the 159 only, APS boards are listed for 136 and 159 in the WNDR Built sweep, and Aluminess retailer pages list 136, 159 and 159 EXT or just 2014+.1522 Check the exact listing for your length.
- Mounting method. Look for pinch-weld brackets, rocker brackets or existing body holes. Ask how many holes you drill. Flatline says drilling and a right-angle drill attachment; CARR drills the pinch weld; one APS owner reports using existing holes plus one drilled hole.1917
- Material and finish. Flatline’s set is steel with a powder coat; a retailer describes the Aluminess steps as rust-free aluminum; Aluminess includes anti-seize because stainless bolts can bind. Ask how to touch up a chipped coating on steel.153
- Tread type. Expanded or open treads shed mud and snow; dimpled and solid surfaces are easier on bare feet. Owners disagree about bare feet on open treads, so check the surface yourself.1417
- Width and projection. A wider board gives a better footing and a bigger lip. Published step widths run from about 6 to 9.5 inches. A step that sticks out makes a wide van wider.4616
- Drop below the body. Ask for the distance from the top of the board to the ground, not just the width. A steel board and its brackets can ride low, and owners hit rocks with them.14
- Load rating. Aluminess lists 300 lb. Flatline, Luverne and APS pages we read do not list a rating, so a lean-a-ladder or stand-a-bike load is an unknown until the maker answers.216
- Stiffness. One owner called APS iBoards “too floppy” and added angle brackets to the supports. Look for how many brackets support each board and where.17
- Compatibility with other gear. Check side ladders, underbody tanks, rock lights and L-Track. Aluminess says some aftermarket conversions are incompatible with its steps.220
- Install effort. Flatline gives 3 to 4 hours; Aluminess says two people; Luverne has a thin manual according to one owner. Match that to your tools and patience.1315
- Warranty. Luverne lists a limited lifetime warranty with shorter finish and parts terms, and its pages disagree on the finish term. Read the terms before you buy.678
- Aluminess Recon step surface6 in
- APS iBoard (named 6 in)6 in
- Luverne Grip Step7 in
- Luverne Grip Step XL9.5 in
Maker and retailer figures, scaled to the widest bar (9.5 in). APS width comes from the product name as owners cite it, not a maker spec sheet. Sources 4, 6, 8, 17.

Specs explained
- Pinch weld (pinch seam)
- The welded seam along the lower edge of the body. Many steps bolt here. Drilling it exposes bare metal, so ask how the maker wants the holes sealed.39
- Rocker mount
- Luverne’s mount-type label for its brackets. Ask exactly where the brackets land on your van.6
- Step surface width
- The standing area, not the overall width. Aluminess lists 6 inches; Luverne lists 7 and 9.5 inches.468
- Weight capacity
- The maker’s figure for one step. Aluminess lists 300 lb per step; the other makers we read list none.24
- Expanded metal tread
- A mesh-style tread with open holes. It scrapes boot soles clean and drains water, but it is harder on bare feet.6814
- Drop
- How far the step’s top surface hangs below the door sill. It decides how high the first step up is and how likely the step is to hit rocks.14
- Right-angle drill
- An attachment for drilling in tight spaces. Flatline says its set needs one, which suggests tight access behind the pinch weld.1
- Interlock or warning lamp
- On a retractable step, a switch that warns you if the step is not stowed. Thule supplies one and describes an optional relay for automatic retraction.1011
Common problems owners report
The threads below are owner reports on the Ram ProMaster Forum, so they are experience, not lab data. Each one comes from a thread we opened; where we read only a search excerpt, we say so.
The step hangs low and breaks off or grinds on rocks
One owner used CARR hoop steps and found them too low for forest roads; they “busted off.” The replacement steel boards stick out less but the owner still grinds them on rocks and says steel can break too.14
What to look for: Ask for the drop below the body and the lowest point of the brackets. Tuck steps close if you drive rough roads, as another owner did with tape marking the edge.14
The install does not go the way the listing implies
An owner with a 2021 van that was listed as compatible with a Luverne kit reported unclear printed instructions, driver brackets that did not fit, underbody structure in the way and what looked like missing brackets.15 Another owner said it took six months to collect enough boards and brackets because they are sold separately.14
What to look for: Confirm the board and bracket part numbers match your wheelbase and side. Luverne’s driver bracket kit is sold separately and marked cab only.7
Boards flex or loosen
One owner who chose APS iBoards found them “too floppy” and added angle brackets to the supports that lean against the frame rails.17 CARR tells installers to retighten all hardware after one month.9
What to look for: Count the support brackets per board, ask about torque specs and schedule a recheck after the first month.
You cannot find the edge when stepping out
One owner removed Westin boards because they “didn’t project far enough out” to step out comfortably when carrying something. Another said steel boards that stick out less are “harder to locate when stepping out.” A third marks the step edge with tape and always backs out of the door.1614
What to look for: Decide whether you value a flush step or a visible one. A retractable step is one answer; one owner marks the edge with tape and another added a grab handle on the pillar.161418
Wide boards are rough on bare feet
Owners shopping for wide boards found that the widest ones were not bare-foot friendly. One bolted a half-inch rubber door mat to the board; another said their boards work fine barefoot.1714
What to look for: Look at the tread pattern in person or ask the brand for a close-up. Dimpled or solid surfaces differ from expanded metal.16
Fitment gaps and one-sided kits
Luverne’s XL board is passenger side only and the driver brackets are a separate part marked cab only.67 Flatline lists the 159 wheelbase only.1 Aluminess retailer pages disagree on whether the 118 is covered.25 Ram’s own sliding-door step is unavailable on the 118.12
What to look for: Write down your wheelbase, body length, side and year, then ask the maker to confirm each against its application list. An owner on a 118 reports using Luverne boards cut to length.14
The step collides with a ladder or other gear
Orion’s ProMaster side ladder bolts to the pinch seam at the bottom and its page says it is not compatible with most full-length running boards, though half or three-quarter boards can work.20 Flatline’s ladder also mounts at the pinch seam.21 Aluminess warns that some aftermarket conversions are incompatible with its products.2
What to look for: Plan ladder and step together. See our ProMaster ladders guide for how side ladders attach.
A powered step adds wiring and a way to forget it
Thule’s step needs a 12 V feed, fuse and switch, and Thule describes a relay for automatic retraction plus a warning lamp so you do not drive off with the step out.1110 Owners recommend the result, but it is a wiring job.1611
What to look for: Ask which mounting kit fits a ProMaster. Thule lists mounting sets by van, and we did not confirm a ProMaster-specific kit page.10

Fitment checklist
Start with the platform basics in our Ram ProMaster fitment guide, which explains wheelbases, roof heights and the 2023 changes. Ram sells the van on three wheelbases (118, 136, 159) plus the 159 EXT body.23 Makers list steps by wheelbase and body length, so ask each for its application list.
- Wheelbase and body. Confirm 118, 136, 159 or 159 EXT. Makers list different wheelbases; Flatline lists the 159 for any roof height.15
- Model year. Luverne lists 2014 through 2026 for its XL board and driver bracket. Aluminess lists 2014 to 2026 or 2027 depending on the page. Ask whether the 2023 and newer body changes affect brackets.672
- Side and door count. The passenger kit needs to cover the front door and the sliding door; a driver kit usually covers the cab door only.48
- Underbody items. Look for conversion tanks, batteries, wiring or earlier steps. Aluminess warns that aftermarket conversions can be incompatible.2
- Roof rack and side ladder. If you plan a side ladder, check the lower mount first. See the ProMaster roof racks guide too.20
- Hitch and rear gear. A hitch conflicts with Ram’s own rear step, and rear-door gear changes how you enter at the back; see the rear door racks guide and the tire carriers guide.12
- Sliding door area. Our fitment guide notes that the sliding-door track location matters for screens and steps, so plan them together; see the bug screens guide and the window covers guide.
- ProMaster EV. We found no maker that states a gas-van underbody step fits the EV, so ask the brand.
Install and long-term ownership
Plan the install before you order. Flatline gives 3 to 4 hours with drilling and a right-angle drill attachment. Aluminess says the install needs two people with a drill, wrenches and a punch or scribe. CARR asks you to avoid bumps and screws on the mounting surface and to adjust for interference.139 An early owner who installed a driver-side step called it a pain because the metal edge under the van is not parallel to the door edge (search excerpt).19
- Test-fit with a helper. Hold the step against the pinch weld and slide it until the brackets line up with the body supports, as Aluminess describes.3
- Level and mark. Make sure the step is level before you drill; Aluminess and CARR both say to level and to mark holes.39
- Drill and deburr. CARR calls for removing burrs, and its materials list includes silicone.9 We found no ProMaster source on sealing drilled holes, so ask the brand what it advises.
- Use anti-seize on stainless hardware. Aluminess includes an anti-seize packet and warns that stainless bolts may bind.3
- Torque and recheck. CARR says to tighten again after one month.9
Long term, check the step after rough roads, retighten hardware and look at the coating for chips where steel is exposed. If you hang a ladder or gear from a step, ask what the mount is rated for. Browse the WNDR Built VanWiki for brand and product pages.
Ask the brand before you order
Ask before you order
- Which wheelbases, body lengths and years does this exact part number fit, including the 118 and the 159 EXT?
- How far does the top of the board hang below the door sill and the body, and how far does it project?
- How many holes do I drill, where, and how should I seal them?
- What load rating applies to the step, and does it change if I lean a ladder or a bike on it?
- Which side ladders, rock lights or underbody parts conflict with this step?
- Is the finish and hardware stainless, powder-coated or anodized, and how is it warrantied?
- Do I need to buy boards and brackets separately, and what is included for the driver side?
Examples in the WNDR Built index
These examples show a feature, not a ranking. The category page and collection list every step we track for the ProMaster.
Example: paired door-zone steps
Aluminess Recon Side Steps (ProMaster)
- 30.75 in driver, 92 in passenger
- 300 lb capacity listed
Aluminess publishes step lengths, a 300 lb capacity, drain holes and mounting provisions for rock lights and L-Track.24 Check wheelbase coverage; retailer pages differ on the 118.5
Example: all-steel set for one wheelbase
Flatline Van Co. ProMaster Side Steps
- 159 wheelbase, any roof height
- Drilling and right-angle drill
Steel tube, steel steps and braces with a powder coat, a published weight of 95 lb and a 3 to 4 hour install.1
Example: widest board
Luverne Grip Step XL (passenger side)
- 9.5 in tread
- Passenger side only
A 7-gauge steel board with expanded treads on rocker-mount brackets; the driver side is a separate part.67
Example: hoop steps at each door
CARR Hoop II Multi-Mount Step
- Pinch-weld mount
- Drilling required
CARR lists the 2014-to-current ProMaster in the instructions and uses shorter spacer tubes for it.9
Example: retractable sliding-door step
Thule Slide-Out Step G2
- 12 V motor
- Manual stow if power fails
Owners recommend it for the sliding door; confirm the mounting kit for your van.1016
Key takeaways
- Match wheelbase, side and year before you compare anything else.1512
- Plan for drilling, a helper and a recheck after a month.139
- Ask for the drop below the body and the load rating; most makers do not publish them.216
- Choose fixed boards for a solid surface and a retractable step if projection is the problem.1610
- Plan side ladders and underbody gear with the step, not after it.20
Frequently asked questions
Do ProMaster side steps need drilling?
Every aftermarket style we read about does. Flatline says drilling and a right-angle drill; Aluminess lists drill bits and self-tapping screws; CARR drills through the pinch weld; one APS owner reports mostly existing holes plus one drilled hole.13917
Which steps fit the 118?
Flatline lists the 159 only, APS boards are listed for 136 and 159 in the WNDR Built sweep, and Aluminess retailer listings disagree. One owner installed Luverne boards on a 118. Ask the maker to confirm your exact van.122514
Can I use my step as a rock slider?
Ask the maker. Aluminess lists 300 lb per step; other ProMaster makers we read publish no rating, and no source says any ProMaster step is a rock slider.216
Is a fixed board or a retractable step better?
It depends on how you step out. Owners who could not see or feel a fixed board when stepping out moved to a slide-out step, which needs wiring and a mounting kit.1611
Will a step block my side ladder?
It can. Orion says its high roof side ladder is not compatible with most full-length running boards because they block the lower mount.20
Does Ram sell a factory step?
Ram’s 2026 buyer guide lists a Mopar sliding-door step, but not for the 118, and a rear bumper step that is not available with the Class IV hitch.12
Keep planning your build
- Fitment guide Ram ProMaster fitment Wheelbases, roof heights and year changes that decide what fits.
- Buyer’s guide ProMaster ladders Side ladders share the pinch seam with your steps.
- Buyer’s guide ProMaster bumpers Front and rear steps, hitches and the 2023 front end.
- Buyer’s guide ProMaster rear door racks What rear-door gear does to rear access.
- Compare platforms Sprinter side steps How the same decisions play out on a Sprinter.
- Compare platforms Ford Transit side steps Step versus rock slider, trim and clearance on a Transit.
Sources
- Flatline Van Co. — Promaster Side Steps checked Nov 2026
- Aluminess — Recon Side Steps, 2014-26 RAM Promaster (maker page; search-result excerpt) checked Nov 2026
- Aluminess — Recon Side Steps installation instructions, P/N 210729 (search-result excerpt) checked Nov 2026
- Campervan HQ — Aluminess 2014+ Ram ProMaster Recon Side Steps (retailer listing; search-result excerpt) checked Nov 2026
- Master Overland — Aluminess Recon Side Steps, Promaster (retailer listing; search-result excerpt) checked Nov 2026
- Luverne — Grip Step XL 9-1/2 in x 54 in Steel Passenger Running Board, Select Ram ProMaster checked Nov 2026
- Luverne — Bracket Kit, Driver Side Only (search-result excerpt) checked Nov 2026
- Luverne — Grip Step 7 in x 54 in Aluminum Passenger Running Board Fleet Kit, Select ProMaster (search-result excerpt) checked Nov 2026
- CARR — Hoop II Multi-Mount Step installation instructions (search-result excerpt) checked Nov 2026
- Thule — Slide-Out Step G2 (product page; search-result excerpt) checked Nov 2026
- Thule — Slide-Out Step V18 12V installation sheet (retailer copy; search-result excerpt) checked Nov 2026
- Stellantis Fleet — 2026 Ram ProMaster buyer guide (search-result excerpt) checked Oct 2026
- PR Newswire — New 2023 Ram ProMaster Unveiled at the Work Truck Week Trade Show in Indianapolis checked Oct 2026
- Ram ProMaster Forum — Running boards/step (owner reports, 2023–2025) checked Nov 2026
- Ram ProMaster Forum — Difficulty installing Luverne 6” grip step running board (owner report, Nov 2021) checked Nov 2026
- Ram ProMaster Forum — Sliding door step recommendations/comments (owner reports, 2019–2022) checked Nov 2026
- Ram ProMaster Forum — Running boards (owner reports, Jul 2023–2025; one reply from a search excerpt) checked Nov 2026
- Ram ProMaster Forum — Grab handle for sliding door install (owner reports, 2015–2024) checked Nov 2026
- Ram ProMaster Forum — Rear Step (owner reports, 2014–2015; search-result excerpt) checked Nov 2026
- Orion Van Gear — Promaster Stealth+ Side Ladder (High Roof) checked Nov 2026
- Flatline Van Co. — Promaster Side Ladder checked Nov 2026
- WNDR Built — catalog sweep of Amazon listings for APS 6 in and 5 in boards, 136 in and 159 in wheelbase, 2014–2026 (verified May 2026; not re-opened) checked May 2026
- Stellantis Fleet — 2025 Ram ProMaster Cargo Van checked Oct 2026
Fitment and availability change. Confirm compatibility with the brand’s application list for your exact van before you buy. Some sources were seen only as search-result excerpts and are labeled that way.
