Ram ProMaster Tire Carriers: What's Available
Share
Most ProMaster cargo vans leave the factory with a spare hung under the rear floor, but a lot of conversions have lost it, and many owners want the underfloor space back for water or fuel. This guide explains where else a spare can go, how each route puts load on the van, what to check before you order, and what owners report going wrong.
- Fits Full-size Ram ProMaster, 2014 to present
- Covers Door, hitch, bumper and front-mount spares
- Sources 30, including owner reports
- Last checked Nov 2026
Quick answer
- Pick the load path first. A door carrier hangs the tire on the hinges or the door skin, a hitch carrier hangs it on the receiver, and a frame-mounted bumper arm carries it on the chassis. Everything else follows from that choice.18910
- Roof height and door side narrow the field fast. Flatline's standalone page lists high roof only, Rover lists high and super high roof, and Aluminess offers its tire rack on the driver-side door only.143
- Most door carriers drill the door. Flatline and Rover use one hole through the door, Landed Gear uses four, while Aluminess and Avatar describe bolt-on mounting with no drilling.14835
- Tire size limits differ by maker. Flatline's standalone carrier lists up to 245/70R16 or equivalent, Avatar's Massif carrier lists up to 275/70R17, and Ram offers LT255/75R16E and 225/75R16C tires.1612
- No door-carrier page we read gives a load rating for the ProMaster door. Published figures cover carrier weight or hitch ratings, so ask where the weight goes.12489
- Check sensors, plate and doors. A spare can set off rear parking sensors, cover the license plate, and change how far the rear doors open.82024
Why move the spare?
On a stock cargo van the spare rides in a carrier under the rear of the van, lowered on a cable by a winch that sits between the right rear tire and the spare.13 That is not guaranteed on your van. Ram sells a full-size spare as an option on the base Tradesman trim and packages it with the SLT trims. Ram also lists a spare tire delete that comes with tire sealant and an air compressor, plus a separate temporary-spare mount option.12
Conversions often lose the factory spare. One retailer that sells ProMaster spare racks says many Class B builds drop the undercarriage spare to make room for a generator or battery bank, and that owners find out at the side of the road.11 A forum owner with a ProMaster-based RV describes the same thing: no spare from the factory and equipment under the van that does not leave room for a full-size tire.15 That is an owner report and a retailer view, not a Ram statement, but it explains why so many ProMaster owners shop for an outside carrier.
The other reason is space. Flatline says moving the spare to the rear door frees underfloor room for a water tank or an auxiliary fuel tank.1 If your build already uses that space, the question is no longer whether to carry a spare outside but how.
Five ways to carry a ProMaster spare
Every product in this category is one of five designs. They differ in where the tire's weight goes, whether you can still open the rear doors, and how much of the van you modify. Our ProMaster tire carriers index lists every product we track by design.

1. Hinge-mounted door carrier with a third point
The carrier clamps to the rear door hinges and adds one more fixing through the door skin, so the tire's weight is shared between the hinges and the door. Flatline's standalone carrier uses stainless hinge brackets plus a single mounting point on the door cut with a drill template, and a dual-shock silicone damper at that third point.1 Rover also mounts on the factory hinges, uses a single hole through the door, and includes a door reinforcement for the mounting area.4 Dark Star's page says only that its carrier is mounted from the hinges.7
2. Hinge-only bolt-on carrier
Aluminess says its ProMaster rack bolts into the factory hinge locations with no drilling, swings out with the door, and fits the driver-side door only.3 Avatar's ladder-and-carrier combo lists driver and passenger versions for a standard-wheel ProMaster and says Transit and ProMaster installs need no drilling.5 Hinge-only designs keep the door skin untouched, but they put the full tire weight through the hinge area, which is the part owners worry about most (see the problems below).
3. Four-point door-skin carrier
Landed Gear takes the opposite approach: a steel mount with four attachment points that spreads the load over the door skin through urethane pads, with two stiffener brackets and a door check strap in the kit. It needs four holes in the door sheet metal.8
4. Hitch-mounted swing-out carrier
A swing-out carrier plugs into the 2-inch receiver and moves the tire off the doors entirely. RIGD's Van-Fit version is designed to sit just below the top of a van bumper so both barn doors can open.9 RIGD's page states that you need 4 inches or less from the hitch-pin hole to the furthest point of the bumper.9 The tire then hangs behind the van, and owners point out that hitch racks on the ProMaster can sit high enough to interfere with the doors.2223
5. Frame-mounted bumper arm, or a front mount
Aareys sells a ProMaster swing-arm bumper that bolts to the frame and, the maker says, puts no weight on the body panels or doors while leaving the rear doors fully usable.10 One owner who installed it says you can swap in a tire carrier on the arm.19 A retailer that sells ProMaster racks describes a fifth route, a front-bumper tire mount that frees both rear doors but, it says, costs some fuel economy and lengthens the van.11 Treat the fuel claim as a retailer's view; we found no measurement.
| Design | Load path | Drilling the door | Rear doors |
|---|---|---|---|
| Hinge plus one door point (Flatline, Rover) | Hinges and door skin | One hole | Open with the tire on the door |
| Hinge-only bolt-on (Aluminess, Avatar) | Hinges | None listed | Open with the tire on the door |
| Four-point door mount (Landed Gear) | Door skin | Four holes | Open with the tire on the door |
| Hitch swing-out (RIGD) | Receiver hitch | None | Carrier swings aside first |
| Frame-bolted bumper arm (Aareys) | Chassis frame | Not applicable | Arm swings aside |
Maker statements, checked Nov 2026. Sources 1, 3, 4, 5, 8, 9, 10. Dark Star lists hinge mounting without further detail.
What to look for
Specs are only half of this purchase. The checklist below covers the parts of a carrier that decide whether it stays tight, keeps the doors working and fits the tire you actually own.
- Where the weight lands. Ask the maker whether the tire's weight goes to the hinges, the door skin, the receiver or the frame, and by what fixings. It matters because owners repeatedly question whether a ProMaster door is meant to carry a wheel.1516 Flatline's third mounting point is built to take impact in both directions to protect the door.1
- Door stop or limit strap. Flatline, Rover, Aluminess and Landed Gear each include a strap or check strap so the door does not swing back into the side of the van.1348 ProMaster rear doors swing about 260 degrees and fold nearly flat, so a loaded door has a long arc to travel.24
- Tire and wheel range. Match the carrier to your real tire. Flatline lists up to 245/70R16, Avatar's Massif carrier lists 27.5 to 33.5 inch tires in its standard size and 32.5 to 37.5 inch in its XD size, and Ram's own tires are LT255/75R16E or 225/75R16C.1612
- Wheel hardware and locks. Look at how the wheel fastens: Flatline ships M14 x 1.5 studs and conical-seat locking lug nuts, Landed Gear ships M16 x 1.5 lug bolts with a wheel lock, and Rover recommends adding a cable lock.184 The wheel's seat shape, bolt pattern and offset must match the hardware.
- Plate, light and handle clearance. The tire can cover the plate and the door handle. Flatline, Aluminess and Rover include plate relocation, Landed Gear's left-door mount comes with a relocator, and one owner who built a door carrier found the tire sat close enough to the handle that the mechanical key might be unusable.1343020
- Parking sensors. Landed Gear sells a mount that raises the wheel to avoid ParkSense sensors and says aftermarket wheels or oversized tires may need a special mount.8
- Which door and which side. Aluminess puts the tire on the driver-side door only, Avatar and Landed Gear offer either side, and a door that already carries a box, rack or AC unit decides this for you.358
- Ladder compatibility. If you want roof access too, check whether the ladder is still usable with the spare on. Aluminess adds three auxiliary steps when you order the ladder with the tire rack, and Rover builds foot pegs into its combo.34 See our ProMaster ladders guide for how these combos compare with side ladders.
- Finish, hardware and warranty. Rover lists a 5-year product warranty and a 10-year finish warranty, and RIGD lists a lifetime warranty.49 We did not find warranty terms on the other ProMaster pages we read, so ask.
- Weight. Published weights vary in what they cover, so compare them cautiously (see the chart below).289
- Landed Gear door mount (without wheel)18 lb
- Flatline ladder and tire carrier combo30 lb
- RIGD UltraSwing with wheel plate (hitch)79 lb
Maker-published figures, checked Nov 2026; the scale tops out at 79 lb. The first two carry weight on the door, the third on the hitch, and the Flatline figure includes a ladder. A wheel and tire add to every one. Sources 2, 8, 9.
Specs explained
- Hinge-mounted vs. door-skin-mounted
- Hinge-mounted means the brackets clamp to the door hinges; door-skin-mounted means bolts or pads sit on the door's sheet metal. Many designs mix both, which is why Flatline and Rover describe hinge brackets plus a single through-door point.14
- Third mounting point
- Flatline's name for the one fixing in the door, fitted with a damper, that stabilises the carrier alongside the two hinge brackets.1
- Door limit strap or check strap
- A strap that stops the loaded door from opening so far that the carrier hits the van's side. Landed Gear also includes two stiffener brackets with its mount.18
- Tire size code (for example 245/70R16)
- Section width in millimetres, then sidewall height as a percentage of width, then rim diameter in inches. A C suffix, as in 225/75R16C, marks a commercial tire. Ram lists LT255/75R16E and 225/75R16C for the ProMaster.12
- Bolt pattern, offset and bore
- An owner quotes the ProMaster's factory wheel as 16 x 6 inches with five lugs on a 130 mm pattern, 68 mm offset and a 78.1 mm center bore. Ram's tire-change guide lists M16 x 1.5 lug bolts at 145 ft-lb in a search excerpt.1513 A carrier plate or stud set has to match the wheel you plan to hang.
- Conical seat
- A cone-shaped seat where the lug bolt or nut meets the wheel. Flatline supplies conical-seat nuts, and a retailer lists the ProMaster's own bolts as a 60 degree conical seat.127
- Combined weight vs. tongue weight (hitch carriers)
- RIGD lists 275 lb combined for the carrier and what it holds, and 150 lb tongue weight on the secondary hitch. The two numbers are separate limits, so a spare and bikes together must respect both.9
- Standard vs. dually
- Avatar's Massif spare carrier lists ProMaster in both standard and dually wheel versions, but its ladder-and-carrier combo lists only standard versions for the ProMaster.56
Common problems owners report
These come from owner posts on the ProMaster Forum and from maker pages. Owner posts are individual experiences, and several are search excerpts, so read them as patterns to check rather than failure rates.
Worry about weight on the rear doors
Owners say the doors and hinges were not designed for a heavy wheel: one thread puts it at 50 lb or more, another says a mount plus tire adds about 75 lb, and a third owner says Ram has asked a lot of the door hardware already.1516 Others report the opposite, such as an owner who carried a spare on the right door for over two years on highway and dirt roads with no problems, and an owner who says the closed door rests on a foot and ramp at the bottom.1618 One owner notes the inboard door edge latches into plates, so the hinged side does not take the whole load.17 Owners of Transit vans have reported door cracking with hinge-mounted carriers, but we found no ProMaster reports of the same.25
What to look for: A design that shares the load across hinge and door, a damper at the fixing point, and a maker willing to say where the weight goes. Ask for any tested load figure; we found none on the ProMaster pages.
Spare lets the tire bounce and the carrier vibrate
An owner who built a DIY door carrier let the tire rest against the bumper with a small spacer so the bumper takes some of the bounce, and found the tire wiggled when it used only two bolts until a third bolt pulled it into light contact with the door.20 Another owner said resting a hinge-mounted spare on the bumper on an older van stopped vibration.29 Rover says its through-door fixing was refined through vibration testing, which is a maker claim.4
What to look for: A carrier that locates the wheel at three points or more, a damper or pad at the door, and tire placement that does not leave it free to rock.
Doors close harder, leak dust or rattle
The ProMaster's rear doors already have seal and latch issues for some owners; one thread calls a stuck rear latch a common issue.28 One owner found the seal did not contact sharp creases in the door edge, and another says adding weatherstrip meant the door needed slight readjustment to close; an owner also reports that adjusting the latch removed a rattle.21 An owner also notes that even well-fitting doors let fine dust in on logging roads.16 Rover says its carrier does not need weather stripping cut or the striker moved, while a competing retailer says another maker's design requires trimming the weather stripping.411 Those are opposing maker claims, so ask whether your carrier changes the door seal.
What to look for: A carrier that leaves the seal and striker alone, a door in good adjustment before you start, and a latch that already closes without force.
Rear parking sensors detect the tire
Landed Gear sells a raised mount for ProMasters with ParkSense sensors, with the wheel set 3 inches higher, and warns that aftermarket wheels or oversized tires may need a special mount.830 A forum owner describes the backup radar beeping constantly because the sensor under the wheel sees it (search excerpt).16
What to look for: Ask whether your van has rear sensors and where the tire will sit relative to them before choosing a carrier.
Wrong roof height, wrong side or wrong wheelbase
Listings do not agree. Flatline's standalone page lists 136, 159 and 159 EXT high roof vans, a reseller listing of the same carrier says standard roof and high roof, and Rover lists high and super high roof.1264 Aluminess offers high-roof and low-roof versions and puts the tire on the driver side only.3 None of the pages we read list the 118 inch wheelbase for the standalone Flatline carrier.1
What to look for: A listing that names your wheelbase, roof height and door side, confirmed by the maker in writing.
Tire or wheel too big for the carrier
Maker limits differ and sometimes disagree with each other. Flatline's standalone carrier lists up to 245/70R16 or equivalent, while its ladder-and-carrier page says the mount fits any tire size that works on a ProMaster. Ram offers LT255/75R16E tires.1212 Avatar's Massif carrier is sized in two ranges, not by tire code.6
What to look for: A tire-size limit you can compare with your actual spare, in writing from the maker.
Hitch carriers foul the barn doors or bumper
ProMaster owners report hitch bike racks that sit so high the doors hang on them. One owner added a 2 inch drop adapter so the door would clear the pivot bolt of a swing-away rack, while another with a non-factory hitch did not need one and found a 5 inch drop too low.2223 One forum owner who uses a generic 2 inch hitch tire carrier warns you may need to grind metal off it so the spare folds down clear of the doors.15 RIGD addresses this with a lower-rise design and a 4 inch hitch-pin-to-bumper limit.9
What to look for: A carrier designed for barn doors, your actual hitch height and bumper depth, and a test swing with the doors before you load it.
The factory spare is missing or its winch fails
Ram's guide says to lower the spare with the supplied winch tool only, and warns that an air wrench or power tool may damage the winch.13 Owners report a broken plastic winch case, advise not to force a stuck winch, and in one case a winch that broke when cranked hard without a click (search excerpt).1415 One owner replaced a '21 spare winch in about 15 minutes.14 And on many conversions the spare is simply absent.1115
What to look for: Check what the van has now before buying a carrier. If you keep the underbody spare, learn the winch procedure and test it.
The spare is hard to lift into place
An owner asking about door carriers got a reply that they had tried lifting a spare that high and decided the undercarriage mount was not so bad after all.19 The tire has to be lifted onto the door-mounted studs or plate, and the mounting height differs by design.
What to look for: Ask how high the wheel sits, whether the carrier has alignment pins or a hanger, and whether you can lift the tire alone.
Fitment checklist
Use this before you compare brands. Our ProMaster fitment guide explains the generations, wheelbases and roof heights behind these questions.
- Confirm wheelbase and roof height. Look for 136, 159 or 159 EXT and the roof height on the listing, and ask about the 118 if that is your van.143
- Pick the door. Decide which side can carry the tire, based on what is already on the doors and the sliding door's position. Aluminess is driver side only.3
- Check what is on the doors and bumper. Rear rack, box, AC, bike carrier or camera: a spare and a rear door rack compete for the same hinges.138
- Measure the tire and wheel. Compare the real spare against the maker's size range and the wheel's offset and bolt pattern.1615
- Check sensors and plate. Note whether the van has ParkSense, and where the plate and light will end up.18
- Check your hitch and bumper. For a swing-out carrier, measure from the hitch-pin hole to the furthest bumper point. If you plan a bumper change, see our ProMaster bumpers guide and rear bumpers guide.910
- Count the rest of the load. Roof gear, ladders and boxes share the same body, and the ProMaster roof racks guide covers the roof side of that load.
Install and long-term ownership
Install effort varies more than the products look. Flatline says its standalone carrier takes about an hour with basic hand tools and one drilled point.1 Landed Gear's four-hole mount, a competing retailer says, ships with a drilling template and is a two-person job; we could not confirm that elsewhere.11 Aluminess ships with instructions and says no drilling is needed.3 The same retailer says lead times on some brands run one to three months, and Aluminess says delivery can take 1 to 8 weeks.113
Plan the work around the door, not just the carrier. Check how the doors close and seal before you start, because adding bracket thickness to a door that already closes hard makes it worse.21 Drilling a door is permanent, so ask each maker how to seal the hole and the exposed metal; the ProMaster pages we read do not give sealing instructions.148
Long term, keep an eye on three things. Look at the fixings and the door edge for movement after rough roads, check that the door still latches without a slam, and look at the finish where the wheel touches paint. The DIY builder found a small stain on the door where the tire touched.20 One owner of a swing-out spare carrier reported rust after winter road salt.15 Our sources give no ProMaster-specific re-check schedule, so ask the maker for one and write the date on the carrier.
A cable lock is a simple theft deterrent for the wheel; Rover recommends one, and Flatline and Landed Gear include locking hardware.418 For payload, remember the carrier and tire sit behind the rear axle. Our rear cargo racks guide covers that side of rear-door loading.

Ask the brand before you order
Ask before you order
- Which wheelbases, roof heights, door side and model years does this exact part number fit, including the 118 and super high roof?
- What is the largest tire and wheel you support, and does that limit apply to the ladder combo too?
- Where does the spare's weight go: hinges, door skin, hitch or frame? Do you have a tested load figure for the ProMaster door?
- How many holes does the door need, where are they, and how do I seal them?
- Does the carrier change the door seal, striker or closing effort, and does it require weather stripping to be trimmed?
- Will rear parking sensors see the wheel, and do you sell a raised or alternate mount?
- Can I still use the ladder, a rear rack or my bike carrier with the spare mounted?
- What are the warranty terms for the structure, the finish and the hardware?
Examples in the WNDR Built index
These examples show a feature, not a ranking. The category page and collection list every ProMaster carrier we track.
Example: hinge brackets plus one door point
Flatline Van Co. ProMaster Rear Tire Carrier
- High roof, 136 / 159 / 159 EXT
- One hole through the door
Aluminum tube frame, a dual-shock damper at the door point, a door strap, and a published tire limit of up to 245/70R16.1
Example: bolt-on hinge mount
Aluminess ProMaster Tire Rack, Hinge Mount
- Driver side only
- No drilling listed
Swings out with the door and can be ordered with a ladder that adds three steps for climbing past the tire.3
Example: hinge mount with door reinforcement
Rover Vans Tire Carrier and Ladder Combo (ProMaster)
- High and super high roof
- 5-year product warranty
Uses the factory hinges plus a single hole and a supplied door reinforcement; the page says the spare sits 14 inches from the back of the van.4
Example: tire carrier that rides on a door rack
Avatar Offroad Spare Tire Carrier for Massif
- Standard and dually
- Needs the Massif system
Mounts above an Avatar storage box on the Massif rack, with two size ranges up to 275/70R17.6 See also the Massif rear door rack VanWiki page.
Example: four-point door mount
Landed Gear ProMaster Spare Tire Mount
- Steel, 18 lb without wheel
- Four holes in the door
Spreads the load over the door skin with urethane pads and offers a raised option for ParkSense vans.8
Example: hitch swing-out
RIGD UltraSwing Van-Fit
- Keeps the doors off the load path
- 4 in hitch-to-bumper limit
Sits below the top of the bumper so both barn doors open, with 275 lb combined and 150 lb tongue ratings.9

Key takeaways
- Choose by load path: hinges and door, hitch, or frame. Then compare brands.18910
- Match roof height, door side and tire size to the listing in writing; makers disagree with each other.124312
- No ProMaster door-carrier page we read gives a door load rating, so ask where the weight goes.148
- Check sensors, plate, door seal and door swing before you drill anything.82021
- If you keep the factory spare, learn the winch procedure and test it.1314
Frequently asked questions
Does a ProMaster tire carrier need drilling?
It depends on the design. Flatline and Rover use one hole through the door, and Landed Gear uses four. Aluminess and Avatar describe bolt-on mounting with no drilling, and hitch carriers need none.148359
Can I still open the rear doors with a spare on?
On door carriers the tire swings with the door. Makers include a strap so the door does not hit the van's side, and one owner reports the door still opened about 180 degrees with the tire acting as a bumper. On hitch and bumper-arm designs, the carrier swings aside first.134820910
Will a spare on the door damage the hinges?
Owners disagree. Some worry the door was never built for a heavy wheel, while others report years of use without problems. We found no ProMaster load rating from Ram or the carrier makers, so ask the brand and see our ProMaster rear door racks guide for the wider door-loading question.151617
What if my van never had a spare?
Ram sells a spare as an option and a delete that adds sealant and a compressor, and conversions often lose the underbody spare. An outside carrier lets you carry one regardless.111215
Door carrier or hitch carrier?
A door carrier keeps the hitch free and moves with the door. A hitch carrier avoids the door but hangs behind the van and has to clear the barn doors and your bumper.92223 A frame-mounted bumper arm is a third option.10
Can I get a ladder and a spare?
Yes, several makers sell combos. Aluminess adds three steps with the tire rack, and Rover and Flatline build foot pegs into their combos. Compare them in our ProMaster ladders guide.342
Keep planning your build
- Fitment guide Ram ProMaster fitment Which wheelbase, roof height and year your carrier has to match.
- Buyer's guide ProMaster ladders Want roof access too? See how rear-door and side ladders compare.
- Buyer's guide ProMaster rear door racks Boxes and bike carriers that share the same door hinges.
- Other platforms Sprinter tire carriers How the same question plays out with Sprinter door hinges.
- Other platforms Ford Transit tire carriers Owner reports on door cracking and hinge-mounted spares.
Sources
- Flatline Van Co. — Promaster Rear Tire Carrier checked Nov 2026
- Flatline Van Co. — Promaster Van Rear Ladder + Tire Carrier checked Nov 2026
- Van Upgrades (Aluminess) — Promaster Tire Rack Hinge Mount and Options checked Nov 2026
- Rover Vans — Tire Carrier & Ladder Combo for Ram ProMaster checked Nov 2026
- Avatar Offroad — Van Rear Ladder Tire Carrier checked Nov 2026
- Avatar Offroad — Spare Tire Carrier for Massif checked Nov 2026
- Dark Star Offroad — RAM ProMaster Ladder Tire Carrier checked Nov 2026
- Landed Gear — Promaster Van Spare Tire Mount Right Hand Door checked Nov 2026
- RIGd Supply — UltraSwing Van-Fit Spare Tire Hitch Mount checked Nov 2026
- Aareys — Ram ProMaster Swing Arm Bumper checked Nov 2026 (search excerpt)
- Juggernaut USA — Ram ProMaster Spare Tire Rack Options (2014–2027): Every Mount Compared checked Nov 2026 (a retailer that sells a competing rack)
- Ram Fleet — 2025 Fleet Buyer's Guide, ProMaster pages (dealer-hosted copy) checked Nov 2026
- Ram — ProMaster Jacking and Tire Changing checked Nov 2026 (search excerpt)
- ProMaster Forum — Spare Tire - underneath location question (owner reports) checked Nov 2026
- ProMaster Forum — Spare Tire (owner reports; replies partly search excerpts) checked Nov 2026
- ProMaster Forum — Spare tire carrier idea for behind rear door (owner reports; replies partly search excerpts) checked Nov 2026
- ProMaster Forum — Weight on rear doors - trouble? (owner reports) checked Nov 2026
- ProMaster Forum — Cheepo spare tire carrier (owner reports, search excerpt) checked Nov 2026
- ProMaster Forum — Rear Door Tire Carriers / Ladders (owner reports) checked Nov 2026
- Build A Green RV — DIY Spare Tire Carrier For ProMaster Van (owner build report) checked Nov 2026
- ProMaster Forum — Why my rear door leaks air and dust (owner reports) checked Nov 2026
- ProMaster Forum — Swing-away bike mount (owner reports) checked Nov 2026
- ProMaster Forum — Rear bike racks (owner reports) checked Nov 2026
- Stellantis Fleet — 2025 Ram ProMaster Cargo Van checked Oct 2026
- Ford Transit USA Forum — Stress on rear door hinges from mounted equipment (owner reports, Transit not ProMaster) checked Nov 2026
- PAD Overland — Promaster Rear Tire Carrier checked Nov 2026 (search excerpt)
- Juggernaut USA — Ram ProMaster Accessories & Upgrades guide checked Nov 2026 (search excerpt)
- ProMaster Forum — Rear door won't open (owner reports, search excerpt) checked Nov 2026
- ProMaster Forum — A DIY Spare Tire Carrier (owner reports, search excerpt) checked Nov 2026
- Master Overland — Landed Gear Rear Door Spare Tire Carrier for Promaster Vans checked Nov 2026 (search excerpt)
Fitment and specifications change. Confirm with the brand before you buy. Forum posts are individual owner experiences.
