
Unaka Gear Co.
Ram ProMaster Side Mount Ladder
Indexed listing. WNDR Built doesn't sell this product; the button opens unakagearco.com.
Side-mounted roof access with a lower pinch-weld anchor
Unaka’s side-mounted ladder joins upper and lower sections into a roof-access assembly. Its top hangs from the roof rack’s side 8020 channel, and a pinch-weld plate anchors the lower section to the van. The top hardware remains adjustable while the installer positions the ladder and checks that it is plumb.
The lower plate and ladder connection are tightened in stages before the top receives its final adjustment, rather than leaving every connection loose until the end.
Textured step plates
Unaka describes the updated step face plates as having a more aggressive, grippy surface.
Rung accessory mounts
Unaka Easy Mount holes on each rung provide attachment points for gear, storage and other accessories.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Unaka Gear Co.
2014+ Ram ProMaster High Roof vans.
Pinch-weld drilling required
Hold the lower bracket against the pinch-weld seam, mark its three holes, drill 1/8 in pilots and enlarge to 3/8 in. Deburr, clean and paint exposed metal before fastening the plate.
Ladder use limits
Unaka says not to use the ladder without appropriate fall protection and personal protective equipment, during storms, when wet, under the influence of drugs or alcohol, or while the van is moving.
Roof-rack attachment
The manual mounts the ladder to a Standard or Premium roof rack’s 8020 side channel. For a Standard rack, use the supplied spacer with the upper ladder half; for a Premium rack, insert the three roll-in T-nuts through the side-rail slot.
Torque checks
Unaka requires torque checks after 4–7 days, after one month, every 3–4 months thereafter, and after moderate driving on bumpy or gravel roads.
Specs, parts & installation
Assembly & attachment
| Sections | Upper and lower ladder halves |
|---|---|
| Rack fasteners | 5/16-18 roll-in T-nuts |
What’s in the box
Ladder & body mount
One upper ladder half, one lower ladder half, one pinch-weld plate and one spacer.
Rack & assembly hardware
Three 5/16-18 roll-in T-nuts; four 5/16-18 × 3/4 in button-head bolts, six 5/16-18 × 1 in hex bolts and three 5/16-18 × 1.25 in hex bolts.
Nuts & washers
Six 5/16-18 locknuts, nineteen 5/16 in washers and seven 5/16 in lock washers.
Installation at a glance
Installation requires a separate ladder; Unaka recommends a qualified professional or following its detailed instructions.
Join the halves and tighten the joint to 11 ft-lb. Hang the top loosely and make the ladder plumb before locating the pinch-weld plate.
Install the pinch-weld plate and torque it to 11 ft-lb now. Push upward from the bottom rungs to align the lower ladder holes, attach the lower ladder and torque that connection to 11 ft-lb now.
Adjust the top, double-check that the ladder is plumb and torque the remaining hardware left loose to 11 ft-lb.
Tools and preparation listed by Unaka
- Separate installation ladder; 1/2 in box wrench, socket and wrench; 3/16 in hex key; torque wrench with 11 ft-lb capacity or higher and socket/Allen adapters.
- Drill with 1/8 in and 3/8 in bits; file or deburring tool, sandpaper, paint-cleaning/preparation materials and paint.
- Unaka suggests an optional dab of anti-seize on bolts paired with nylock nuts; anti-seize is not included.
Upper-mount details
- If a side-panel screw interferes with rack mounting, remove it and slide its existing T-nut over to use that location; the manual says this leaves an extra roll-in T-nut.
Lead Time
Unaka’s Shipping Information excludes oversized items from free shipping, and its Shipping policy excludes items shipped by LTL freight.
This product
Unaka’s product page advertises free shipping on large Unaka products, including roof racks and ladders, to the Lower 48.
Warranty
Unaka-designed and fabricated parts have a defects warranty for the original purchaser during the product’s production lifetime; third-party kit components and wear parts are excluded, coatings have 180-day coverage, and modification or misuse voids the warranty.
Read Unaka Gear Co. warranty policy on WNDR BuiltReturns
The Refund policy’s Returns section requires an RMA, new condition, original packaging and freight-prepaid returns, with no refunds after 30 days from invoice and a minimum 10% fee if the customer covers shipping or 20% otherwise; its Terms & Conditions of Sale instead lists 15 days from receipt and a 15% fee. Custom, electronic, discontinued and specially priced items are excluded; the Sale terms also exclude opened or installed parts.
Read Unaka Gear Co. returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon