
Unaka Gear Co.
Mercedes Sprinter Wheel Wrap Ladder
Indexed listing. WNDR Built doesn't sell this product; the button opens unakagearco.com.
A wheel-well cutout for side-mounted roof access
The Wheel Wrap ladder adds a cutout around the wheel-well area to Unaka’s side-mounted ladder design. Unaka says this allows mounting closer to the wheel well without obstructing side windows. Its upper and lower halves join into one assembly, with the top attached to a roof rack and the bottom secured to a pinch-weld plate.
Unaka also provides a mounting route without a roof rack: a separately sold adapter connects the ladder to OEM Sprinter rails. That route still uses the ladder’s lower mounting installation; it changes the upper attachment rather than replacing the lower anchor.
Textured step plates
Unaka describes the updated step face plates as having a more aggressive, grippy surface.
Rung accessory mounts
Unaka Easy Mount holes on each rung provide attachment points for gear, storage and other accessories.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Unaka Gear Co.
2007+ Mercedes-Benz Sprinter High Roof vans.
Pinch-weld drilling required
The lower plate mounts on the outside/front of the pinch-weld seam. Mark and center-punch the holes, drill 1/8 in pilots, enlarge to 3/8 in, then deburr, clean and paint exposed metal.
Ladder use limits
Unaka says not to use the ladder without appropriate fall protection and personal protective equipment, during storms, when wet, under the influence of drugs or alcohol, or while the van is moving.
Roof-rack attachment
The manual mounts the ladder to a Standard or Premium roof rack’s 8020 side channel. For a Standard rack, use the supplied spacer with the upper ladder half; for a Premium rack, insert the three roll-in T-nuts through the side-rail slot.
OEM rail attachment
OEM Sprinter rails can be used without a roof rack, but require Unaka’s separately sold factory-rail adapter. Its guide uses the ladder’s bolts and washers at the upper attachment and the ladder manual to complete the lower installation.
Wheel-wrap positioning
Align the wrap pinch-weld plate with the end of the pinch-weld seam so the wrapped lower section follows the wheel well; keep the ladder plumb.
Torque checks
Unaka requires torque checks after 4–7 days, after one month, every 3–4 months thereafter, and after moderate driving on bumpy or gravel roads.
Specs, parts & installation
Assembly & attachment
| Sections | Upper and lower ladder halves |
|---|---|
| Rack fasteners | 5/16-18 roll-in T-nuts |
What’s in the box
Ladder & body mount
One upper ladder half, one wheel-wrap lower half, one wrap pinch-weld plate and one spacer.
Rack & assembly hardware
Three 5/16-18 roll-in T-nuts; four 5/16-18 × 3/4 in button-head bolts, six 5/16-18 × 1 in hex bolts and three 5/16-18 × 1.25 in hex bolts.
Nuts & washers
Six 5/16-18 locknuts, nineteen 5/16 in washers and seven 5/16 in lock washers.
Installation at a glance
Installation requires a separate ladder; Unaka recommends a qualified professional or following its detailed instructions.
Join the halves and tighten the joint to 11 ft-lb. Hang the top loosely and make the ladder plumb before locating the pinch-weld plate.
Install the pinch-weld plate and torque it to 11 ft-lb now. Push upward from the bottom rungs to align the lower ladder holes, attach the lower ladder and torque that connection to 11 ft-lb now.
Adjust the top, double-check that the ladder is plumb and torque the remaining hardware left loose to 11 ft-lb.
Tools and preparation listed by Unaka
- Separate installation ladder; 1/2 in box wrench, socket and wrench; 3/16 in hex key; torque wrench with 11 ft-lb capacity or higher and socket/Allen adapters.
- Drill with 1/8 in and 3/8 in bits; file or deburring tool, sandpaper, paint-cleaning/preparation materials and paint.
- Unaka suggests an optional dab of anti-seize on bolts paired with nylock nuts; anti-seize is not included.
- The drilling step also calls for a center punch and hammer.
Upper-mount details
- If a side-panel screw interferes with rack mounting, remove it and slide its existing T-nut over to use that location; the manual says this leaves an extra roll-in T-nut.
- For the separate factory-rail adapter, slide its carriage-bolt/bracket assemblies into the rail end. Leave its upper hardware loose until the lower brackets are installed, finish the ladder manual’s sequence, then tighten the adapter hardware left loose to 11 ft-lb.
Lead Time
Unaka’s Shipping Information excludes oversized items from free shipping, and its Shipping policy excludes items shipped by LTL freight.
This product
Unaka’s product page advertises free shipping on large Unaka products, including roof racks and ladders, to the Lower 48.
Warranty
Unaka-designed and fabricated parts have a defects warranty for the original purchaser during the product’s production lifetime; third-party kit components and wear parts are excluded, coatings have 180-day coverage, and modification or misuse voids the warranty.
Read Unaka Gear Co. warranty policy on WNDR BuiltReturns
The Refund policy’s Returns section requires an RMA, new condition, original packaging and freight-prepaid returns, with no refunds after 30 days from invoice and a minimum 10% fee if the customer covers shipping or 20% otherwise; its Terms & Conditions of Sale instead lists 15 days from receipt and a 15% fee. Custom, electronic, discontinued and specially priced items are excluded; the Sale terms also exclude opened or installed parts.
Read Unaka Gear Co. returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon