
Unaka Gear Co.
V1 Mercedes Sprinter Roof Rack - Premium - 170" High Roof
Indexed listing. WNDR Built doesn't sell this product; the button opens unakagearco.com.
An adjustable roof layout with aluminum side plates
This V1 Premium roof rack provides an adjustable framework for a Sprinter roof build. Its crossbars can be positioned along the side rails to suit the layout, including solar panel placement. The rack combines a 15 series 8020 aluminum foundation with a laser-cut aluminum shell, adding side plates and an aluminum wind fairing around the underlying rail structure.
The installation guide describes top-mounted solar panels resting over the side rails. Smaller panels can instead sit down between the rails with separately purchased flush-mount brackets. The wind fairing also has adjustment slots for its fore-and-aft position and angle, so its final position is set during assembly.
Channel-mounted accessories
T-nuts slide into the 8020 channels for crossbar brackets and accessories; the guide calls for installing solar and accessory T-nuts during assembly.
Joined side rails
Splice plates join the front and rear 8020 side rails; the guide provides adjustments for interference with crossbar brackets or solar panels.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Unaka Gear Co.
- 2007+ Mercedes Benz Sprinter High Roof Vans · 170" wheelbase · V1 Premium rack.
Two-person roof access
The installation guide requires two people and two ladders tall enough for the work, on a level area; accessing the roof presents a fall hazard.
Solar panels and flush brackets sold separately
Solar panels are sold separately. Flush-mount solar brackets are not included with this rack kit.
Light bar compatibility
Unaka lists no light bar capability for this rack.
Additional solar mounting holes
If adding holes to a solar panel, the guide calls for a backer board inside the panel to prevent drilling through it.
Required roof rails
Factory-style roof rails must be installed before fitting the rack. Unaka’s guide permits OEM or aftermarket rails and states its washer plates have been tested with OEM and Van Tech rails.
Top-mounted solar panels
The installation guide specifies 200W and larger panels with a maximum panel length of 55.28", resting over the side rails.
Flush-mounted solar panels
For smaller panels mounted between the side rails, the guide requires a total width less than 52.75" and separately purchased flush-mount solar panel brackets.
Solar bracket requirements
The guide specifies minimums of 4 brackets for panels smaller than 150W, 8 brackets for panels greater than 150W up to 250W, and 16 brackets for panels 300W and larger; follow the solar panel manufacturer’s requirements if it recommends more.
Specs, parts & installation
Rack construction
| Foundation | 15 series 8020 aluminum |
|---|---|
| Shell and wind fairing | Laser-cut aluminum shell; aluminum wind fairing |
| Crossbars | Ultra Lite 15 series 8020; black, grooved, 53.75" long, as listed in Unaka’s installation guide. |
| Installation hardware | Stainless steel, as listed on Unaka’s product page |
What’s in the box
Rack and fairing
Roof rack with aluminum wind fairing, side rails, side plates, mounting brackets and installation hardware.
Crossbars
Four 8020 crossbars with brackets and hardware, following Unaka’s Revision 3 installation guide.
Solar panel mounting
Top-mount solar panel brackets and mounting hardware for two 200W solar panels; Unaka’s installation guide lists 16 top-mount brackets.
Installation at a glance
Unaka’s installation guide requires two people and two ladders.
Assemble the rack and slide the adapter brackets into the installed roof rails; position and square the side rails and crossbars before final tightening.
Trim the wind-fairing bulb seal to length as needed and fit it before the fairing’s final installation.
Unaka recommends a qualified professional or installation according to its detailed instructions.
Check all hardware for correct torque when finished; recheck after 4 to 7 days, after 1 month, every 3 to 4 months, and after moderate driving on bumpy or gravel roads.
Tools and assembly supplies in the guide
- Torque wrench, ½" and 7/16" sockets and box wrenches, 3/16" and 5/32" Allen tools, tape measure and two ladders.
- Loctite 242 on bolts not used with nylock nuts; Loctite C5-A anti-seize on bolts paired with nylock nuts, following the guide’s step-specific instructions.
Solar mounting details
- If adding panel mounting holes, place a ½" or ¾" backer board inside the panel, center-punch, drill an 1/8" pilot and finish with a 5/16" bit; remove all drill shavings.
- For a single bracket at the 8020, use the guide’s 5/16-18 x 9/16" bolt; when two panels share a T-nut through overlapping brackets, use the 5/16-18 x 5/8" bolt.
- The guide specifies 75.2 in-lbs for attaching solar brackets to the panel and 132 in-lbs for securing the panel brackets to the crossbars; follow the complete guide for all other fasteners.
Source notes
- Unaka’s product page lists five crossbars; its Sprinter 170 Premium Revision 3 installation guide lists four in the parts table and hardware for four on page 5. This listing follows the guide.
- Unaka’s product page gives a maximum solar panel width of 55.25"; its Revision 3 guide specifies a maximum panel length of 55.28" for top mounting. This listing follows the guide.
- Unaka’s Sprinter 170 Premium Revision 3 installation guide, page 15, states “150W Solar Panel or Smaller: Minimum 4 Brackets” and “150W to 250W Solar Panel: Minimum 8 Brackets”; these overlap at exactly 150W, so this listing omits a bracket minimum for that wattage.
Lead Time
LTL and oversized items exclude free shipping; Route protection is optional; international ordering without a checkout option is described separately on two pages.
Read Unaka Gear Co. lead time policy on WNDR BuiltWarranty
Original purchasers have production-lifetime defect coverage on Unaka-designed and fabricated parts; coatings have up to 180 days, and third-party kit components and wear items are excluded.
Read Unaka Gear Co. warranty policy on WNDR BuiltReturns
Refund policy sections state 30 days from invoice with at least 10% or 20% restocking, versus 15 days from receipt with 15%; RMA required.
This product
Unaka’s product page describes discounted remaining V1 stock; its refund policy excludes discontinued and specially priced items from returns.
What are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon