
Unaka Gear Co.
Ford Transit Roof Rack - Standard - 148" High Roof
Indexed listing. WNDR Built doesn't sell this product; the button opens unakagearco.com.
Adjustable crossbars for a Transit roof layout
The Unaka Standard roof rack provides a modular aluminum framework for arranging equipment on a van roof. Its crossbars can be positioned along the side rails rather than held at fixed mounting points, so their locations can be set around the planned roof layout.
This Standard version pairs a 15-series 8020 foundation with an acrylic wind fairing. Unlike the Premium rack described alongside it on Unaka’s page, it uses exposed black-anodized 8020 rather than the Premium model’s laser-cut aluminum shell and aluminum fairing. T-nuts slide into the extrusion channels to attach the crossbars and accessories; their placement is part of assembly, before the rack closes off access to those channels.
Repositionable crossbars
Crossbars slide along the side rails; their positions can be adjusted to avoid interference with the fixed roof brackets and inside splice plates.
Adjustable fairing position
Slotted wind-fairing brackets allow slight forward and backward adjustment.
Channel-mounted accessories
The manual calls for installing accessory T-nuts during assembly for items such as solar panels, awnings and tie-downs.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Unaka Gear Co.
- 2015+ Ford Transit · 148" wheelbase · High Roof
- Unaka states compatibility with the new 2026 Transit antenna location.
Roof preparation may require trimming
If a factory threaded insert does not align with the roof opening, the manual requires trimming the roof opening with tin snips and smoothing its edges. Do not force the mounting bolt. In rare cases, paint inside an insert requires clearing with an M8x1.25 hand tap.
Two-person installation
The model-specific manual requires two people and two sufficiently tall ladders on level ground. The unopened shipping box should also be handled by two people.
Roof load and decks
Unaka’s Transit 8020 guide directs customers to follow the vehicle manufacturer’s roof-load guidelines and does not recommend building a roof deck platform.
Light bar capability
Unaka lists no light-bar capability for the Standard rack.
Additional installation supplies
Tools, Dicor sealant and anti-seize are not included. Solar panels are sold separately.
Optional panel drilling
If adding panel mounting holes, place a ½” or ¾” backer board inside the panel, use a center punch and an 1/8” pilot bit, finish with a 5/16” bit, and remove drill shavings.
Solar panel size
Unaka’s product page states a maximum solar panel width of 60.6".
Rack configuration
This listing is the fixed Standard 148" High Roof rack, not the Premium, Premium + Light Bar Capability or Explorist.Life racks described on the maker’s page.
Solar bracket requirements
The manual specifies minimums of 4 brackets for a 150W solar panel or smaller, 8 for a 150W to 250W panel, and 16 for a 300W panel or larger; follow the panel manufacturer’s requirements if it specifies more.
Specs, parts & installation
Frame and fairing
| Foundation | 15-series 8020 aluminum |
|---|---|
| Finish | Black anodized 8020 |
| Wind fairing | Acrylic |
| Crossbar length | 59.63” in the model-specific manual |
| Side rail section length | 53.69” in the model-specific manual |
What’s in the box
Rack structure
Four 8020 side rail sections, four ultralight 15-series 8020 crossbars, eight roof rack brackets and four inside splice plates.
Fairing and finishing parts
Acrylic wind fairing, bulb seal, one center fairing bracket, two mid fairing brackets, two outside fairing brackets and four end caps.
Mounting hardware
Crossbar connectors and rack installation hardware; the product page specifies stainless steel hardware.
Installation at a glance
Use the model-specific Standard 148” High Roof manual; installation requires two people and two ladders.
Remove the covers at the rack mounting locations, check factory threaded-insert alignment, then assemble and position the brackets, side rails, crossbars and fairing. The rear bracket location has no threaded insert.
Seal all four sides of each roof bracket, the hex bolt and the sealing washer with Dicor, following Dicor’s instructions, before installing solar panels. Do not overtighten hardware against the acrylic fairing.
The model-specific manual specifies 132 in-lbs. for the final roof/adapter and side rail assembly tightening, fairing-to-crossbar hardware and crossbar-to-side-rail hardware; use the manual’s separate values for other connections.
Check torque after 4 to 7 days, after 1 month, every 3 to 4 months and after moderate driving on bumpy or gravel roads.
Assembly preparation
- Identify the parts and keep sub-kit hardware separate; similar-looking pieces are not necessarily interchangeable.
- Pre-install the required T-nuts for the fairing, solar panels and other accessories before later assembly blocks channel access.
- The manual specifies Loctite 242 for bolts not used with nylock nuts and says it is pre-applied to the kit bolts; reapply if a coated bolt is loosened repeatedly.
- Use the crossbars to set parallel side rail spacing, center the rack, and tighten and seal roof brackets before covering them with panels.
Tools identified by the manual
- ½” and 7/16” SAE sockets and wrenches; 13mm metric socket and wrench; 3/16 T-handle, 1/8 and 5/32 Allen wrenches.
- Torque wrench, tape measure, two ladders, tin snips, file, sandpaper, caulk gun and paint cleaning/preparation materials.
- A heat gun and plastic scraper are used to remove roof caps; keep the heat gun moving to avoid finish damage.
Optional solar panel mounting
- Apply anti-seize to the ¼-20 panel-bracket bolts. The narrow bracket slot attaches to the panel and the wide slot to the 8020.
- When two panels share a T-nut, use the manual’s longer bolt for the two overlapping brackets rather than the shorter single-bracket bolt.
Source notes
- Unaka’s 7/1/25 Standard 148” High Roof manual specifies 132 in-lbs. at final rack/roof, fairing and crossbar tightening steps; the product-linked 6-5-2023 Transit 8020 guide instead specifies 168 in-lbs. for roof-mount M8 bolts and 13 ft-lbs. (156 in-lbs.) for remaining 8020 hardware; this listing follows the model-specific manual.
- The model-specific manual’s page 4 lists 16 flush-mount solar panel brackets and two solar bracket/hardware kits, but pages 15–16 mark solar bracket installation Sold Separately; Unaka’s product page promises hardware for two solar panels, so disputed solar bracket and kit quantities are omitted from the included list.
- Unaka’s product-page compatibility section includes 2015+ Transit High Roof and 2015+ Transit 148 Medium Roof; this listing follows the 148” High Roof scope of its title and model-specific manual.
- Unaka’s FAQ estimates 2-3 hours for a solo Standard rack installation, but the model-specific manual requires two people and two ladders; this listing follows the manual.
- Unaka’s product-page banner advertises free shipping on roof racks to the Lower 48; its Shipping Information page excludes oversized items from free shipping, and its Shipping policy excludes items that ship via LTL freight.
Lead Time
LTL and oversized items exclude free shipping; Route protection is optional; international ordering without a checkout option is described separately on two pages.
Read Unaka Gear Co. lead time policy on WNDR BuiltWarranty
Original purchasers have production-lifetime defect coverage on Unaka-designed and fabricated parts; coatings have up to 180 days, and third-party kit components and wear items are excluded.
Read Unaka Gear Co. warranty policy on WNDR BuiltReturns
Refund policy sections state 30 days from invoice with at least 10% or 20% restocking, versus 15 days from receipt with 15%; RMA required.
Read Unaka Gear Co. returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Owner reports
Quotes from owners and installers, with links to where they were posted. These are owner reports, not manufacturer-confirmed information, and may describe a different van or year than yours. Verify before you buy.
I used the high roof 148” rack on my 130” mid roof and it fit well without any cutting or issues
View originalSearches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon