
Tec Vanlife
Sprinter Modular Drop Down Running Boards – Hexagon Series
Indexed listing. WNDR Built doesn't sell this product; the button opens tecvan.com.
Modular steps for cab and sliding-door access
Tec Vanlife lists modular Hexagon Series drop down running boards for Sprinter vans, offered as 2-, 3- or 4-piece sets. The sets cover driver and passenger step positions, with sliding-door steps added according to the selected set. This separates the stepping platform into dedicated door sections.
The footbeds have a ribbed surface for anti-slip traction. Molded brackets with bendable tabs to adjust for uneven undercoating. Tec Vanlife describes the tabs as adapting to irregularities in the undercoating at the mounting locations.
Coated aluminum tube
Coated aluminum construction around a 1.75" aluminum tube.
Sliding-door operation
Tec Vanlife states the boards do not interfere with sliding door operation.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Tec Vanlife
2007+ Sprinter vans · 144" and 170" wheelbases.
Choose your step set
Tec Vanlife offers these three step configurations.
2 Piece Set - Driver / Passenger
- Driver step
- Passenger step
3 Piece Set - Driver / Passenger / Sliding Door Steps
- Driver step
- Passenger step
- Sliding door step
4 Piece Set - Driver / Passenger / 2x Sliding Door Steps
- Driver step
- Passenger step
- Two sliding door steps
Drilling required
The installation guide requires drilling mounting holes with a 9 mm bit and drilling the vehicle underbody with a 5 mm bit to secure the support pieces with rivets. Apply anti-corrosion oil to the drilled holes.
Ground clearance
Ground clearance is reduced by approximately 6–8 inches (15–20 cm).
Specs, parts & installation
Construction & capacity
| Material | Coated aluminum |
|---|---|
| Tube | 1.75" aluminum tube |
| Weight capacity | Tec Vanlife states approximately 400 lbs. |
Dimensions — installation guide
| Driver/Passenger step | 840mm (33") × 195mm (7 2/3") × 146.1mm (5 3/4") |
|---|---|
| Sliding door step | 1560mm (61.5") × 195mm (7 2/3") × 146.1mm (5 3/4") |
Component weights — product page
| Driver/Passenger step | 7.32 lb (3.32 kg) |
|---|---|
| Sliding door step | 14.88 lb (6.75 kg) |
| Support bracket | 1.48 lb (0.67 kg) |
What’s in the box
Steps
Driver and passenger steps, plus the sliding door step or steps specified in the selected set. Mounting hardware included.
2-piece set hardware — guide package list
4 support brackets; 32 M8 x 35 bolts; 32 M8 x 35 self-locking nuts; 32 washer plates; 5mm x 10mm rivets.
3-piece set hardware — guide package list
6 support brackets; 48 M8 x 35 bolts; 48 M8 x 35 self-locking nuts; 48 washer plates; 5mm x 10mm rivets.
Tools & treatment — 2- and 3-piece guide package lists
One 5mm drill bit, one 9mm drill bit, one L shaped hex key and one anti-corrosion oil container per set.
Installation at a glance
Tec Vanlife’s product FAQ lists approximately 2 hours for one person, using a drill and basic hand tools.
Follow the installation guide for the drilled, bolted and riveted mounting method; use a brush to apply anti-corrosion oil to drilled holes.
After installation, recheck and retighten all mounting hardware at approximately 100 miles, then every 600 miles, and inspect the boards, brackets and mounting points every 600 miles or at least once a month, whichever comes first.
Guide installation sequence
- Position and level the component, align it and mark the drilling points.
- Drill the marked mounting holes with the 9 mm bit and apply anti-corrosion oil.
- Insert M8 × 35 bolts from front to back through the component mounting points; fit the support brackets, washer plates and self-locking nuts, then tighten evenly so the brackets sit flush.
- Align the footbed with the brackets and secure it with M8 × 35 bolts, washers and self-locking nuts, tightening evenly.
- With the running board and support pieces held against the vehicle underbody, drill the aligned upper support holes with the 5 mm bit and treat the holes with anti-corrosion oil.
- Fit the 5 mm × 10 mm rivets to secure the upper support sections to the underbody; repeat the procedure for the remaining running board sections.
Source notes
- Tec Vanlife’s installation guide package lists on pages 2–3 each list eight 5mm x 10mm rivets, while Steps 6–7 call for four upper holes and rivets on each support piece and Step 8 repeats the procedure for remaining sections; the rivet quantity is omitted from this listing.
- Tec Vanlife’s product FAQ says light drilling is required on the inner panel only and no underbody modification is needed; its installation guide calls for 9 mm mounting holes and 5 mm holes into the vehicle underbody. This listing follows the guide.
- Tec Vanlife’s product page lists a 7.66" footbed width and 146mm height; its installation guide lists 7 2/3" and 146.1mm. This listing follows the guide.
- Tec Vanlife’s key features say all 2007+ Sprinter wheelbases, while its product FAQ specifies 144" and 170"; this listing uses the FAQ’s narrower wheelbase scope.
Lead Time
Cancel before shipment; pre-shipment refund requests incur 6%. Address changes are free before courier pickup, $25 afterward; contact the seller for shipping outside the lower 48.
This product
Tec Vanlife’s product page states free shipping to the lower 48 states and Portland warehouse pickup usually ready in 24 hours.
Warranty
Read Tec Vanlife warranty policy on WNDR BuiltReturns
Returns within 30 days incur 15% restocking plus original and return shipping charges; refund requests before shipment incur a 6% transaction fee.
Read Tec Vanlife returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon