
Flatline Van Co.
Winnebago Ekko Rear Bumper
Indexed listing. WNDR Built doesn't sell this product; the button opens flatlinevanco.com.
A rear step and mounting base for the Ekko
Replace the rear bumper with an aluminum skin supported by steel mounting brackets and step supports. Flatline Van Co. builds a lowered step into the bumper for access to the rear ladder, alongside a license-plate holder and auxiliary-light pockets.
Cover plates close the light pockets when lights are not fitted. A separate cutout accepts the rear-platform mounting hardware, with a cover plate for use without the platform. This makes the bumper both a rear step and the mounting base for the platform-and-carrier arrangement.
Factory ladder compatibility
The lowered step can be used with the factory ladder or Flatline’s Ekko Rear Ladder.
Stainless hardware
The bumper uses stainless steel hardware.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Flatline Van Co.
Winnebago Ekko only: 2025+ Winnebago Ekko Sprinter (23B) and 2021+ Winnebago Ekko Transit (22A).
Drilling and wiring required
Mounts to existing holes with brackets to the subframe; some drilling is required. The guide opens four factory rear frame holes to 39/64 in for tube spacers, replaces the two forward-most factory hitch-receiver bolts with longer supplied hardware, and drills the new license plate bracket to 5/8 in for the LED light. The factory plate light wiring is migrated to the new bracket, so note the wire colors before disconnecting it.
California Proposition 65
Flatline warns that this product can expose you to lead and lead compounds, DEHP and bisphenol A (BPA), which California identifies as causing cancer and birth defects or other reproductive harm.
Companion parts
The bumper installs independently. The Ekko rear platform requires this bumper, and the tire carrier requires the platform. These and the Ekko Rear Ladder are separate add-ons on the maker page, as are Baja Designs S2 light pods (SAE, S2 Sport driving/combo and S2 Sport wide cornering); none is included.
Installer requirement
Flatline recommends professional installation generally. If you have no mechanical experience and are not thoroughly familiar with the installation procedures, a professional installer or other qualified person must install the product.
Before use
Check mounting points and attachments before use, and regularly inspect the product for wear or damage, as required by Flatline’s guides.
Specs, parts & installation
Construction & lighting
| Materials | Aluminum bumper skin, steel mounting brackets and steel step support, stainless steel hardware |
|---|---|
| Lighting | Built-in mounting for Baja Designs S2 auxiliary lights; cover plates included for when lights are not installed |
Installation time
| Time | 2 hours per the installation guide |
|---|
What’s in the box
Bumper & brackets
Bumper skin assembly with left and right mounting brackets and pivot mounting plates.
Plate and cover parts
License plate bracket, tube spacers, backer plates and tire-carrier cover plate; light-pocket cover plates.
Hardware & wiring supplies
Hardware, panel plugs, rubber grommet, cable ties and threadlocker per the installation guide.
Installation at a glance
Flatline’s guide lists 2 hours, with extra help suggested for some steps.
Remove the factory bumper, enlarge the mounting holes, fit the brackets and bumper skin, and migrate and reconnect the license plate light wiring.
Installation sequence and tools
- Flatline’s guide lists about 2 hours, with extra help suggested for some steps
- Remove the factory license plate light and bracket and the four bolts holding the factory bumper, then drill the four factory rear frame holes to 39/64 in and press in the aluminum tube spacers
- Assemble the left and right brackets with the pivot mounting plate, bolt them at the hitch-receiver locations and to the rear wall with backer plates, and fit the bumper skin on the pivot plate
- Install the LED plate light in the new bracket, move the factory wiring across, then check alignment, torque the bolts and reconnect the lights
- Tools listed include a power drill, 39/64 and 5/8 in bits, deburr tool, wire strippers, flush cutters and 7/16, 9/16 and 3/4 in sockets plus 5/32 and 7/32 in Allen wrenches.
Lead Time
Flatline Van Co. says in-stock items ship within 1–2 business days from its Arizona warehouse. Items sent by LTL freight typically take 7–21 business days to arrive. Its FAQ says shipping is free to the lower 48; its Shipping policy lists flat-rate shipping and possible free economy shipping with longer lead times.
Read Flatline Van Co. lead time policy on WNDR BuiltWarranty
One-year limited warranty from the original purchase date for the original purchaser, covering product cost only. It excludes installation, labor and freight, and damage from racing, competition or trail use, and is void for alteration, modification or improper installation.
Read Flatline Van Co. warranty policy on WNDR BuiltReturns
Returns are accepted within 30 days of receipt with a pre-authorized RMA number, for unused items in resalable condition and original packaging. A 20% restocking fee applies, and the customer pays return shipping unless the return is due to Flatline’s error; LTL freight returns must be coordinated with Flatline. Clearance, garage-sale and final-sale items are not returnable, and custom or made-to-order items may also be non-returnable.
Read Flatline Van Co. returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon