
Flatline Van Co.
Transit Van Rear Bumper
Indexed listing. WNDR Built doesn't sell this product; the button opens flatlinevanco.com.
A metal replacement for the Transit rear bumper
The Flatline Van Co. Transit Van Rear Bumper replaces the factory bumper with an aluminum skin over a steel substructure. Its low-profile shape follows the van’s body lines; Flatline says the design preserves ground clearance and departure angle while allowing the rear doors to function.
A dimpled step surface provides a place to stand when accessing the van and lets water drain through. Integrated light cutouts and a wiring channel accommodate rear lighting, while cover plates close the openings when running without lights. The bumper also incorporates D-ring recovery mounts, with their use limited to recovery rather than flat towing.
Mixed-metal construction
An aluminum outer skin is supported by a steel substructure and stainless steel brackets.
Rear lighting provisions
Cutouts accept Baja Designs S2 SAE or S2 Sport LED Light Pods, with a built-in channel for routing wiring.
Factory sensor transfer
The installation guide transfers the original blind spot and parking sensors, their bezels and wiring into the replacement bumper.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Flatline Van Co.
- 2020+ Transit 150/250/350 | 130"/148"/148" EXT | Mid/High Roof
- 2023-2024 Transit Trail | 148"/148" EXT | Mid/High Roof
Cutting required
The guide requires trimming the factory taillight trim pieces to fit. Additional factory plastic tabs or other interfering areas may need trimming after dry-fitting the bumper.
Recovery only
The incorporated D-Ring Mounts are for recovery situations only. Flatline states its products are not intended for flat towing.
Factory sensor reuse
Retain and transfer the factory parking-sensor bezels, parking sensors, blind spot sensors and wiring. Preserve each sensor’s factory side, orientation and location.
California Proposition 65
Flatline warns that this product can expose you to lead and lead compounds, DEHP and bisphenol A (BPA), known to California to cause cancer and birth defects or other reproductive harm.
Hitch compatibility
Flatline states the bumper works with or without a factory hitch. When reinstalling a hitch, the guide specifies either 2 or 3 screws/washers per side depending on whether it is a factory or aftermarket hitch.
Recovery hardware
Tow hooks fit 3/4" D-Rings with 7/8" Pin.
Installer requirement
Flatline recommends professional installation. If you have no mechanical experience and are not thoroughly familiar with the installation procedures, its guide requires a professional installer or other qualified person.
Before use
Check mounting points and attachments before use, and regularly inspect the product for wear or damage.
Specs, parts & installation
Construction
| Outer skin | 3mm aluminum skin |
|---|---|
| Brackets | 5mm stainless steel brackets |
| Substructure | Steel |
| Mounting hardware | Grade 8 zinc yellow-chromate mounting hardware |
| Finish | UV-rated black powder coat finish |
| Weight | 81 lbs |
What’s in the box
Bumper assemblies
One bumper skin assembly, one step support, one left side mounting arm and one right side mounting arm.
Hardware and wire management
Mounting screws, washers, nuts, cable ties and a threadlocker bottle, as listed in the installation guide.
Lighting covers
Cover plates for use without lighting.
Installation at a glance
Flatline’s installation guide states 2-3 HOURS, with additional help suggested for some steps.
Work on a flat surface and disconnect the battery (both if applicable) before electrical work.
Remove the factory bumper, transferring its sensors, bezels and harnesses; retain the factory T25 screws for reassembly. Remove and reinstall the tow hitch and disconnect/reconnect its trailer harness if applicable.
Install the mounting arms and step support with the supplied hardware and threadlocker where the guide specifies. Dry-fit the skin, trim factory plastic as required, secure the bumper and reconnect all sensor harnesses.
Use a body saw for the specified trim work; the guide also calls for hand tools. If fitting off-road lights, Flatline advises having them ready before installing the bumper.
Removal and sensor transfer
- Lower and remove the spare tire with a 1/2” square drive if applicable to access the frame bolts.
- Get help removing the heavy tow hitch and handling the factory bumper, as recommended in the guide.
- Keep each sensor harness on its original side. Tuck wiring behind mounting surfaces, away from the mounting arms, but accessible for reconnection; use the supplied cable ties for wire management.
Optional lighting
- Remove the cover plates and install off-road lights using the light manufacturer’s supplied hardware.
Tools listed in the guide (not included)
- Auto panel removal tool; flathead screwdriver; T25 Torx; T20 Torx; 1/2” square drive.
- 13MM and 15MM wrench/socket; 18MM wrench; 5/32” and 7/32” Allen wrenches; 7/16” and 9/16” sockets; body saw.
- The individual steps also call for pliers and masking tape.
Source notes
- Flatline’s product page says it includes parking sensor bezels; guide pages 15 and 17 instruct reusing the factory bezels. This listing follows the guide.
- Flatline’s product description says 2015 and newer Ford Transit vans; its fitment block lists 2020+ Transit 150/250/350 and 2023-2024 Transit Trail. This listing uses the narrower fitment block.
- Flatline’s FAQ says all products ship free to the lower 48; its shipping policy offers paid flat-rate shipping and potentially free economy shipping. The bumper page specifically states free contiguous-US freight delivery.
- Flatline’s FAQ gives most transit times as 1-3 days to the Western USA and 3-5 days to the Eastern USA; its shipping policy lists typical freight delivery as 7-21 business days, while the bumper page estimates 1-2 weeks.
Lead Time
In-stock dispatch: 1–2 business days; LTL delivery: typically 7–21 business days; preferred service uses flat rates; economy may be free with longer lead times.
This product
Flatline’s product page estimates arrival within 1-2 weeks and describes free pallet-freight delivery to homes in the contiguous US.
Warranty
Flatline-made products have a one-year limited warranty for the original purchaser; purchaser-paid claim returns and exclusions apply; other manufacturers’ products carry only their applicable manufacturer warranties.
Read Flatline Van Co. warranty policy on WNDR BuiltReturns
Returns within 30 days of receipt require RMA, unused original-packaged items and 20% restocking; customer-paid shipping unless Flatline error; clearance/garage-sale/final-sale excluded; identified custom/made-to-order exclusions may apply.
Read Flatline Van Co. returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon