
Dark Star Offroad
Mercedes Sprinter Tire Carrier
Indexed listing. WNDR Built doesn't sell this product; the button opens darkstaroffroad.com.
Move the spare out of its stock holder
This carrier relocates the Sprinter's spare tire from the stock holder to the rear door. Dark Star Offroad describes the change as freeing the stock holder while making the spare easier to reach, and its guide says the carrier can accommodate an oversize spare.
The assembly mounts at the hinges and at a separate door attachment, with a urethane bushing between the door plate and carrier. An alignment stud supports positioning the spare during mounting; wheel studs, locking lug nuts and a lug-nut key are included.
Alignment for mounting
The guide uses an alignment stud to line up the spare before the wheel studs secure it.
Bushed door attachment
A round urethane bushing sits between the door plate and the tire carrier.
Locking wheel hardware
Three locking lug nuts and a lug-nut key are listed in the packing list.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Dark Star Offroad
The linked guide identifies 2014-CURRENT MERCEDES-BENZ SPRINTER 1500, 2500, 3500.
180-degree hinges required
The guide requires 180 hinges and states that 270 hinges will not work.
Drilling and door clearance
Drill a ⅛” pilot hole through the outer and inner door skin, then enlarge it with a ⅜” drill bit. Use a step bit on the exterior and interior sides if needed for clearance; the guide also calls for inside clearance to attach the washer and nut. Treat exposed metal edges with a rust-preventive coating.
Door position
The guide installs the carrier on the rear driver-side door.
Specs, parts & installation
Mounting hardware
| Hinge fasteners | Four M10 x 20mm stainless BHCS |
|---|---|
| Door fastener | One ⅜-16 x 2-½” socket head bolt |
What’s in the box
Carrier & plates
One DSO Sprinter tire carrier, one upper hinge mounting plate, one lower hinge mounting plate and one door mounting plate.
Alignment & bushing
One alignment stud and one round urethane bushing.
Wheel hardware
Three wheel studs, three locking lug nuts and one lug-nut key.
Mounting fasteners
Four M10 x 20mm stainless BHCS, one ⅜-16 x 2-½” socket head bolt, two ¾” washers and one ⅜-16 nylon-insert locknut.
Installation at a glance
The guide estimates 4 hours and calls for a helper to position the carrier and lift the spare.
Park on a level surface and remove factory plastic door trim if present.
The carrier mounts to the factory hinges and a separate door attachment.
Installation sequence from the maker guide
- Check upper and lower hinge-plate orientation against the guide images.
- Snug the four M10 x 20mm bolts with a 6mm Allen key without fully tightening; align the door bracket and mark the door.
- After drilling and coating the exposed edges, peel off the 3M tape backing and attach the door bracket to the rear driver-side door.
- Place the round bushing between the door plate and carrier, insert the provided 2-½” bolt, and fit the washer and nylon-insert nut from inside the door.
- Verify the fasteners, fit the alignment pin, and lift the spare with a helper; secure it with the three supplied wheel studs or studs of your choice as stated in the guide.
- Ensure all fasteners are properly secured.
Tools listed by Dark Star Offroad
- Power drill; ⅛” metal pilot drill bit; ⅜” metal drill bit; step drill bit
- 6mm Allen key as specified in installation step 3
- 9/16” socket with extender; 9/16” wrench
- Rust Bullet or another rust-preventive coating for exposed edges
Lead Time
Read Dark Star Offroad lead time policy on WNDR BuiltWarranty
Read Dark Star Offroad warranty policy on WNDR BuiltReturns
Full refunds are offered on new, unused parts; installed parts cannot be returned, and Off Highway Van does not cover return shipping.
Read Dark Star Offroad returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon