
White Top Adventures
TRANSIT REAR TIRE CARRIER LADDER
Indexed listing. WNDR Built doesn't sell this product; the button opens whitetopadventures.com.
Spare-wheel storage with roof-rack access
This rear-door carrier holds a full-size spare and doubles as a roof-rack ladder on a Ford Transit. White Top Adventures lists carrying a spare, mounting a recovery board and reaching the roof rack as its uses. The frame is powder-coated aluminum with a stainless-steel spare-wheel mounting plate and an integrated silicone dampener to limit vibration and rattle.
A threaded center rod and winged handle hold the wheel. The guide’s mounting arrangement uses brackets at both rear door hinges and a third attachment through the door, keeping the wheel carrier and ladder on the same frame.
Wheel attachment
The wheel secures with a tire cone and winged handle.
Climbing hardware
The guide includes two foot pegs, installed after securing the carrier.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by White Top Adventures
- 2015+ Ford Transit Crew and Cargo vans (mid roof and high roof vans, all wheelbases).
- 2023+ Ford Transit Trail.
Drilling required
The guide requires two holes through both layers of rear-door metal for the third mount, using what it calls an “M8 drill bit”.
Backup sensors
White Top's FAQ says the ladder position can register as an obstruction for the backup sensor on some 2023 Ford Transit models; the common fix is to adjust the ladder mounting position slightly or adjust the sensors.
Door and hinges
Designed to mount to the driver-side rear door hinges, and White Top says it is compatible with both hinge types. If the Transit has 180° hinges, the guide says to insert the supplied hinge spacer between the hinge and the upper hinge bracket.
Wheels
If an aftermarket wheel has a lower offset than the factory wheel, the guide says the included spacer plate can provide extra clearance.
Ladder reach
White Top says the Transit ladder does not extend quite as high as the Sprinter version.
Step holes
White Top's FAQ says the holes in the ladder steps are not standard L-Track holes. For accessories, the maker says a T-bolt tie-down anchor may work and asks buyers to contact it to confirm the current options for their setup.
Installer requirement
White Top’s guide recommends professional installation. If you lack mechanical experience or are unfamiliar with the procedures, a qualified professional or someone with the necessary expertise must install it.
Before use
Inspect mounting points and attachments before use, and regularly check for wear or damage, as required by White Top’s guide.
Specs, parts & installation
Construction
| Frame | Powder-coated aluminum |
|---|---|
| Wheel mount | Stainless-steel spare-wheel mounting plate |
| Dampener | Integrated silicone dampener |
Maker load ratings
| Static load | White Top states 300 lbs; the page adds “Unless otherwise specified by the manufacturer”. |
|---|---|
| Dynamic load | White Top states 300 lbs; the same manufacturer qualifier applies. |
What’s in the box
Carrier and brackets
Main frame and frame tube; hinge spacer; double and triple bolt plates; rubber strip; drill-through plate and frame brace; lower and upper hinge brackets; foot pegs ×2.
Wheel mount
Winged handle, two tire cones (one small, one wide) and the spacer plate identified as included in the guide’s wheel-mounting step.
Hardware
M8x50 socket head screws ×2; M16x300 W-lock screw ×1; M8x35 socket head screws ×2; M8x35 flanged hex head screws ×6; M8 washers ×10; M16 washers ×2; M10x80 socket head screws ×2; M8 nylon locknuts ×10; M16 nuts ×2.
Installation at a glance
White Top’s FAQ quotes one customer at about 3 hours; the guide calls for assistance when raising the carrier into place.
Remove the lower panel and peel back the vapor barrier. Fit hinge brackets, the third-mount assembly, center rod and support tube, then secure the carrier and wheel. Add Loctite to the foot-peg screws.
Guide assembly sequence
- Remove the upper door hinge bolts and thread the hinge through the upper hinge bracket; refasten with the supplied bolts and washers.
- Use the drill-through bracket to locate the third mount just above the outward door curve; remove the carrier before drilling.
- Assemble the drill-through bracket, gaskets and plate against the door, fastening with the black M8x35 bolts, washers and nuts.
- Fit the M16x300 center rod with M16 washers and nuts, then attach the support tube with two M10x80 socket head screws.
- With help, raise the carrier and secure both hinge brackets with the triple bolt plate and nuts; secure the third mount with the double bolt plate. The guide says the hinge nuts can be tightened “all the way”.
- Attach the wheel using the cone and winged handle, with the spacer plate if needed for clearance, then fit the foot pegs.
Lead Time
Free shipping: most continental-US orders on Shipping policy, all lower-48 orders on FAQ, all orders on Homepage banner; remote-location and special-freight fees may apply.
This product
White Top’s product-page FAQ says in-stock orders ship the same day or next business day via UPS/FedEx and arrive in 3–7 business days.
Warranty
Read White Top Adventures warranty policy on WNDR BuiltReturns
Returns within 30 days of delivery require unused, uninstalled, unassembled items in original packaging; 15% restocking and customer-paid shipping apply; large freight items have additional fees.
Read White Top Adventures returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon