
Van Compass
SIDE LADDER - SPRINTER (2007-CURRENT, LOW ROOF ONLY) by VAN COMPASS (CLOSEOUT)
Indexed listing. WNDR Built doesn't sell this product; the button opens vancompass.com.
Side access to the roof
This Van Compass side ladder provides roof access with an upper mount that hooks over the outer corner of the van’s body line. The lower end attaches to Van Compass rocker guards or uses a standalone lower mount, giving vans without those guards a separate mounting route.
The ladder combines steel sides with aluminum rungs. Van Compass places the rungs ~4" from the body and says the rocker-guard mounting arrangement preserves ground clearance. The upper mounts arrive with 3M adhesive tape on their contact surfaces to adhere to the cleaned van body.
Hook-over upper mounts
The upper mounts hook onto the outer corner of the van’s top body line without drilling into the roof.
Two lower mounting routes
Choose a rocker-guard attachment or the standalone lower mount to suit the equipment on the van.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Van Compass
Van Compass’s product-page fitment guide lists Sprinter 2500 and 3500 LOW ROOF, 2007-PRESENT, 4X4 and AWD.
Choose the lower mounting position
Vans without Van Compass rocker guards must order the standalone version.
ATTACH TO VC ROCKER GUARDS
- Requires Van Compass 4022 rocker guards installed first, as specified by the ladder guide.
STAND ALONE MOUNT - 2WD AND 4X4
- Includes the standalone lower mount when selected.
- The standalone guide replaces steps 1–4 of the ladder guide, so this route does not require rocker guards.
Standalone mount requires drilling
The standalone lower mount guide requires drilling two mounting holes with a ¼-inch bit and painting exposed metal to prevent corrosion. The roof attachment itself requires no drilling.
Helper required
The ladder guide calls for a helper when fitting the ladder and a 100-200lb helper to pull down or stand on it during final tightening. This is an installation instruction, not a ladder load rating.
Roof equipment
Requires factory roof tracks. Van Compass states compatibility with Sportsmobile penthouse tops; the ladder guide describes compatibility with a Sportsmobile pop top.
Mounting location
The rocker-guard guide documents the driver-side rear-most position and allows positioning forward along the rocker guards. The standalone mount guide allows mounting along the side from the back of the front doors to the front of the rear wheel wells.
Installer requirement
Van Compass strongly recommends a certified mechanic. Otherwise, the installer must read, understand and follow all application instructions and warnings; the warranty policy requires professional installation.
Specs, parts & installation
Ladder construction
| Sides | 1/8" steel |
|---|---|
| Rungs | 1/8" aluminum |
| Rung clearance | Van Compass states the rungs are spaced ~4" away from the body. |
What’s in the box
Ladder and roof attachment
Steel ladder sides, aluminum ladder rungs, rocker-guard tie-in plate, two upper mounts with 3M adhesive tape, and attachment hardware for the Van Compass rocker guards and roof.
Ladder hardware
The ladder guide lists ¼-20 x 1.0" stainless steel button-head cap screws, serrated flange nuts and stainless flat washers.
Standalone option
When selected, the standalone lower mount includes top and bottom brackets, six ¼-20 x 1.0" stainless steel button-head cap screws, six serrated flange nuts and six stainless flat washers.
Installation at a glance
The ladder guide lists approximately 1-2 hours; the standalone lower mount guide separately lists 30min -1 hour.
For the rocker-guard option, install the rocker guards first and attach the ladder through the tie-in plate. For the standalone option, install the lower mount before following the ladder assembly instructions, disregarding ladder-guide steps 1–4.
Test-fit the upper mounts and clean their contact areas before exposing the adhesive. Fit the ladder with a helper, keep it adjustable until loaded as directed, then tighten the upper and lower side-rail attachment bolts to 80 in-lbs. (9 N.m), upper bolts first.
Tools listed in the guides
- Ladder: standard A-frame ladder, 7/16” wrench/socket and 5/32” Allen wrench/socket bit.
- Rocker-guard attachment uses the rocker-guard installation tool included in the rocker-guard kit.
- Standalone lower mount: floor jack, level, drill with ¼” metal-cutting bit, 7/16” wrench/socket and 5/32” Allen wrench/socket bit.
Standalone lower mount sequence
- Position the top bracket with a floor jack, hook its tabs beneath the pinch seam, level it and mark the two mounting holes.
- Remove the bracket, drill the two holes and paint exposed metal.
- Assemble the brackets loosely, then lift the assembly into place with the pinch seam sandwiched between the top and bottom brackets.
- Install the inner bolts and tighten inner and outer hardware to 80 in-lbs. (9 N.m.) before proceeding to ladder assembly.
Source notes
- Van Compass’s product-page fitment guide lists 4X4 and AWD, while its standalone buy option says “STAND ALONE MOUNT - 2WD AND 4X4”; 2WD fitment remains unconfirmed here.
- The low-roof ladder guide’s parts list specifies six rungs, but step 6 refers to seven; this listing omits the disputed rung quantity.
- The low-roof ladder guide requires rocker guards for its lower mount; the standalone lower mount guide explicitly supports this low-roof ladder and replaces steps 1–4, providing the alternative mounting route.
- The standalone mount guide’s parts-list heading says TALL ROOF, but its general notes explicitly state that the mount is for either the low-roof or tall-roof side ladder.
- The product page gives recommended shop labor of 1 Hour; the low-roof ladder guide gives approximately 1-2 hours, which this listing follows; the standalone guide separately gives 30min -1 hour.
Lead Time
Orders ship first-come, first-shipped; international service is described separately on two pages; report loss, missing items or damage within 2 days of tracked delivery.
Read Van Compass lead time policy on WNDR BuiltWarranty
Specified hard parts: original-owner ownership term; Falcon shocks: 1 year; powder coating/excessive zinc corrosion: 60 days; professional installation required.
Read Van Compass warranty policy on WNDR BuiltReturns
Return-window start date varies by page; eligible unused returns incur 20% restocking and customer-paid shipping; electronics, including PedalBox, and CLOSEOUT items are final sale.
This product
Van Compass’s Shipping, Return and Cancellation Policies page states that all CLOSEOUT items are non-returnable and all sales are final; this ladder is marked CLOSEOUT.
What are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon