
Van Compass
FRONT WINCH BUMPER - SPRINTER (2015-2018) by VAN COMPASS
Indexed listing. WNDR Built doesn't sell this product; the button opens vancompass.com.
A winch mount behind the factory bumper cover
This Van Compass system replaces the factory bumper beneath its plastic cover to provide a front winch mounting point for off-road recovery. The cover is refitted around the winch fairlead after trimming, rather than being replaced with an exposed bumper.
The mount also accepts bolt-on recovery points and a front receiver. These attachments can be installed together or in any combination. The installation guide places the receiver on the same four bolts that secure the winch, so the receiver configuration is decided when fitting the winch.
Bolt-on recovery points
The two front recovery points are 3/4" thick and designed for ¾” D-ring style shackles.
Coated steel construction
The mount uses steel plate and square tube, finished in black powder coating over a zinc primer.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Van Compass
- Mercedes Sprinter NCV3, 2014–2018, following the winch-mount installation guide.
- Sprinter 2500 and 3500; 4X4 and 2WD, as listed in the product-page fitment guide.
Engine and cooling exclusions
Not compatible with 4-cyl diesel or gas engine. Not compatible with vans fitted with the HD Rear AC Package because the additional cooling fans do not clear.
Front receiver and collision sensors
The front hitch should only be used on vans without collision assist / brake sensors; carrying gear can cause sensor warnings.
Cutting and trimming required
Installation requires removing and trimming the plastic front bumper cover, cutting the factory metal tow-point tube and its inner corner, and trimming a small piece of the intercooler. The step tread plate also requires trimming; the receiver and recovery points require their corresponding bumper-cover cutouts when installed.
Front license plate mounting
The winch-mount guide says the factory front license plate mounting is not retained and identifies alternative mounts for Hawse and Roller fairleads.
Older-mount retrofit only
The recovery-point guide calls for drilling mounting holes when retrofitting the points to an older winch mount. It states that current winch mounts already have these mounting holes.
Winch sizing
The winch-mount installation guide specifies the Warn Zeon series and uses the Warn Zeon 12 as the maximum-size reference for other winches. The illustrated installation uses a Warn Zeon 12S on a 2015 4x4 2500 Sprinter Crew Van; installation varies with year, chassis configuration and winch choice.
Installer requirement
Van Compass strongly recommends installation by a certified mechanic. Its warranty policy requires professional installation according to the instructions.
Specs, parts & installation
Construction
| Steel plate | 3/16" |
|---|---|
| Square tube | 1/4" square tube, as stated by Van Compass |
| Recovery-point thickness | 3/4" |
| Finish | Black powder coating with zinc primer |
| Product weight | 52lbs, as stated by Van Compass |
Receiver
| Receiver size | 2" |
|---|---|
| Vertical load limit | Van Compass’s winch-mount installation guide states a maximum vertical load capacity of 300lbs. |
What’s in the box
Mount and attachments
Front winch mount, front hitch receiver tube and two bolt-on shackle recovery points.
Installation supplies
Mounting bolts, nuts and washers, plus a 2ML tube of blue Loctite listed in the winch-mount guide.
Installation at a glance
The winch-mount guide estimates 6–7 hours, depending on the complexity of winch wiring.
Remove the grille, bumper cover and factory bumper; carry out the metal, intercooler, bumper-cover and tread-plate trimming described in the guide, then bolt in the mount and refit the cover. Paint exposed cut metal to prevent corrosion.
Fit the receiver, if used, with the winch mounting bolts; fit the recovery points if desired. Follow the winch manufacturer’s instructions for winch installation, fairlead torque and wiring: Van Compass’s guide does not cover winch wiring.
Disconnect fog-lamp wiring and any rear-of-bumper module, if equipped, during removal; reconnect electrical components and the ambient air temperature sensor during reassembly. Some fairleads require additional trimming of the tread plate’s horizontal rib.
Tools listed by Van Compass
- Torque wrench, basic wrench and socket set, T25 Torx bit, 13mm and 18mm metric sizes, and ¾” SAE size.
- Automotive trim removal tool and suitable cutting tools for metal and plastic, such as the guide’s listed angle grinder, pneumatic cut-off tool, sawzall, die grinder or Dremel-style tool.
- The installation steps also reference T-45 fasteners for the top step, and Phillips or T-20 fasteners for the license plate mount, as equipped.
Older-mount recovery-point retrofit
- The separate recovery-point guide estimates 1–2 hours for retrofitting points to an older mount.
- Locate the points level with the chassis against the inner welds; mark and center-punch the mounting holes, drill a pilot hole, then open to ½” (13mm). Deburr and paint exposed metal.
- Trim the bumper cover for the recovery points and test-fit for final clearance, following the recovery-point guide.
Source notes
- Van Compass’s winch-mount installation guide, version 2.1, lists 2014–2018; the product title and product-page fitment guide list 2015–2018. This listing follows the installation guide.
- Van Compass’s winch-mount installation guide and product description specify Warn Zeon 12 as the maximum-size reference; the product-page fitment guide specifies Warn VR 12-S. This listing follows the installation guide.
- Van Compass’s product page recommends 6 Hours of shop labor; the winch-mount installation guide estimates 6–7 hours depending on winch-wiring complexity. This listing follows the guide.
- The winch-mount guide’s hardware table describes the M12 bolts as 50MM LONG, while their part designation and step 28 say 40mm. This listing omits the disputed bolt length.
- The recovery-point guide’s title and compatibility note say 2007–2018, while its parts-list heading says 2007-PRESENT; these refer to the recovery points and do not widen the winch mount’s vehicle fitment.
Lead Time
Orders ship first-come, first-shipped; international service is described separately on two pages; report loss, missing items or damage within 2 days of tracked delivery.
Read Van Compass lead time policy on WNDR BuiltWarranty
Specified hard parts: original-owner ownership term; Falcon shocks: 1 year; powder coating/excessive zinc corrosion: 60 days; professional installation required.
Read Van Compass warranty policy on WNDR BuiltReturns
Return-window start date varies by page; eligible unused returns incur 20% restocking and customer-paid shipping; electronics, including PedalBox, and CLOSEOUT items are final sale.
Read Van Compass returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon