
Unaka Gear Co.
Sprinter - Rear Ladder System - Base Kit
Indexed listing. WNDR Built doesn't sell this product; the button opens unakagearco.com.
A MOLLE-panel base for Sprinter rear-door gear
The Sprinter Rear Ladder System Base Kit provides a rear-door mounting platform that can be expanded with a ladder extension, tire carrier, boxes or other gear. It is a modular starting point that can be used on its own and expanded over time, rather than replacing the whole rear setup as the build changes.
The integrated MOLLE panel accepts front-mounted hardware, so gear can be installed without reaching behind the panel or removing other equipment. Unaka offers separate driver-side and passenger-side versions. On the passenger side, a cable-operated pull handle maintains access to the factory door handle through the mounted frame.
Integrated dampening
Unaka says its built-in dampening system reduces shock to protect the rear door.
MOLLE mounting pattern
The panel accepts Unaka MOLLE nuts or 3/8" carriage bolts for front-side accessory mounting.
Visibility-conscious layout
Unaka says the system is designed to minimize taillight interference, avoid triggering backup sensors and keep the license plate visible.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Unaka Gear Co.
- 2019+ Mercedes Benz Sprinter Vans with 180 hinges (VS30)
- 2020+ Winnebago Revel & Storyteller Overland with 180 hinges (Mercedes Sprinter models)
Choose the rear-door side
Choose the kit for the door where the base system will mount.
DRIVER SIDE
- Driver-side frame and mounting hardware.
PASSENGER SIDE
- Passenger-side frame with a cable-operated door pull handle.
180° hinges required
Install only on 180° rear-door hinges. After installation the door no longer opens a full 180°; do not force it open because mounted gear may damage the van body or taillights.
Rear wiper condition
If the van has rear windshield wipers, Unaka recommends removing or disabling the wiper arm before installation because of the system’s close fit.
Door drilling and interior access
Both side-specific manuals require drilling the third mounting point and access inside the door to check for cables, wiring, insulation or other obstructions. Remove obstructing trim as needed and deburr, clean and paint exposed metal. Panel-style trimmed doors also require interior drilling and the supplied plug.
Passenger-side handle drilling
The passenger-side kit requires a 3/32" hole through the factory door handle for its pull cable; avoid drilling into the door.
Accessories sold separately
The upper ladder extension is sold separately; the tire carrier and other additions are accessories to the base system.
Close the passenger door with care
The passenger-side manual warns that added door weight makes it close with significantly less effort; avoid slamming it.
Before use & maintenance
Unaka requires an initial torque check after 4 to 7 days, a follow-up after 1 month, checks every 3 to 4 months, and checks after moderate driving on bumpy or gravel roads. The passenger-side guide also recommends hardware checks before or after long trips.
Specs, parts & installation
Accessory interface
| Panel pattern | MOLLE |
|---|---|
| Front-side fasteners | Unaka MOLLE nuts or 3/8" carriage bolts |
| Required hinge type | 180° rear-door hinges |
| Door travel after installation | Less than a full 180° |
What’s in the box
Selected base & mounting parts
Driver-side or passenger-side frame, upper/lower hinge washer plates, third-mount main boss, rubber dampener, sealing washers, inside panel plug, mounting hardware and step drill bit.
Door-specific preparation
Driver-side drill template or passenger-side door drill template, as appropriate to the selected kit.
Passenger-side handle components
Passenger-side kit includes the pull-handle cable and wire ferrules; its handle assembly is fitted to the frame.
Installation at a glance
Unaka recommends a second person for part of the installation.
Use the manual for the selected side. Prepare and drill the third mounting point, loosely fit the frame at the hinges and third mount, then align it before final tightening. The passenger-side installation also drills the factory handle and routes, tensions and tests a pull cable before trimming it.
Unaka recommends professional installation or following its detailed manual.
If adding an upper ladder extension, Unaka recommends fitting it to the base kit before bolting the base to the van.
For either Sprinter side, torque the hinge hardware to 15 ft lbs; do not torque the third-point hardware, which is tightened only until the rubber seals/bosses compress slightly.
Third-mount preparation
- Check inside the door for obstructions, remove trim if needed, and use the correct side-specific template to locate the third mount.
- Drill a 3/16" pilot, then a 3/8" hole through the layers specified in the matching guide. Enlarge the outside opening to 23mm with the supplied step bit.
- For panel-style driver-side doors, enlarge the inside opening approximately 24.5 to 25mm, testing the supplied plug as you go; the passenger-side guide specifies a 23mm inside opening. Deburr, clean and paint the cut edges.
Frame alignment and tightening
- Loosely attach the frame through the hinge holes and add the third-point hardware without fully tightening.
- Center the main boss in the 23mm opening; snug hinge hardware, recheck alignment, then snug the third point.
- Torque hinge hardware to 15 ft lbs. Do not torque the third-point hardware; tighten it only enough to slightly compress the rubber seals/bosses.
Passenger-side handle sequence
- Drill the specified 3/32" hole in the factory handle, fit the small washer and thread the cable through the handle.
- With the frame still loose, feed the cable through the frame housing and barrel nut. Do not cut or tighten it at this stage.
- After frame alignment, tension the cable with the pull handle retracted, secure the barrel screw and test opening and closing. Adjust tension before cutting.
- Only after testing, trim the cable within the handle profile, crimp on its end cap and reinstall the handle cover.
Tools listed in the side-specific manuals
- Drill, 3/16" and 3/8" drill bits, 7/32" Allen tool, 9/16" sockets, extensions, torque wrench (15 ft-lbs), file, sandpaper and paint-cleaning/prep materials; the step bit is included.
- Passenger side additionally uses a 3/32" bit, 1/8" Allen tool, wire cutters and needle-nose pliers; door access may require trim-removal tools.
Lead Time
Unaka’s Shipping Information page excludes oversized items from free shipping; its Shipping policy also excludes items shipped by LTL freight. For international orders, Shipping Information invites contact if checkout shows no shipping method, while Shipping policy says no displayed option means the country is not served.
This product
The product-page banner advertises free shipping on large Unaka products to the Lower 48; the brand’s oversized-item and LTL exclusions still appear in its policy pages.
Warranty
Unaka’s Refund policy covers workmanship and material defects for the original purchaser for the product’s production lifetime on Unaka-designed and fabricated parts, excluding third-party components, wear parts and modification or misuse; coatings are covered for up to 180 days after purchase.
Read Unaka Gear Co. warranty policy on WNDR BuiltReturns
The Refund policy’s Returns section allows refunds within 30 days of invoice, with a minimum 10% restocking fee if the customer covers shipping or 20% if forgoing shipping costs; its Terms & Conditions of Sale instead states 15 days after receipt and a 15% fee. Returns require an RMA, new condition, original packaging and prepaid freight; custom, electronic, discontinued and specially priced items are excluded, and the Terms & Conditions also excludes opened or installed parts.
Read Unaka Gear Co. returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon