
Vanspeed
Transit Scout Side Steps
Indexed listing. WNDR Built doesn't sell this product; the button opens vanspeedshop.com.
Side steps that replace the factory rocker trim
Vanspeed’s Transit Scout Side Steps add stepping surfaces for getting in and out of the van while replacing its factory plastic rocker trim. Their bent sheet-metal construction creates a low-profile assembly along the lower body, with step platforms carried by lower supports and joined to replacement trim and valences.
The driver-side valence also provides mounting locations for a Vanspeed Scout Side Ladder or other accessories. This gives the step assembly an accessory-mounting role as well as an entry step.
Perforated leading edge
The step platforms have a perforated linear cut pattern along their leading edge, which Vanspeed says provides additional traction.
Three stepping locations
Separate platforms serve the driver door, passenger front door and sliding door.
Cut, bent and welded
The steps are CNC cut, bent and welded, and manufactured in Huntington Beach, CA.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Vanspeed
2015+ Ford Transit 148
Factory trim removal
Installation requires removing the OEM plastic rocker trim on both sides of the van.
Drilling required
The guide requires drilling the vehicle’s pinch seam, working up to an 11/32” bit at locations clear of spot welds. It also directs installing two 5/16” hex-head drilling screws through the ladder support into the rocker panel.
Exterior clearance
Vanspeed’s guide requires confirming clearance for other exterior components before installation.
Accessory mounting
The driver-side valence slots accept 5/16” & M8 hardware for a Vanspeed Scout Side Ladder or other accessories.
Ladder support position
If also installing a Scout Side Ladder, choose the support position to match the ladder’s intended location. The guide shows position 01 for a capsule and position 02 for no capsule; without a Scout Side Ladder, either position works.
Bracket placement
If the ladder support is closest to the rear wheel arch, the guide requires loosening its right-hand bolt from Step 18 and installing the rocker valence bracket behind the ladder support.
Specs, parts & installation
Construction & finish
| Material | Combination of 1/8” & 3/16” steel |
|---|---|
| Finish | Textured black powder coat |
What’s in the box
Platforms & toe kicks
Driver, passenger and sliding-door step platforms, each with its corresponding toe kick.
Lower supports
Four lower supports: driver front step, passenger front step, sliding-door left and sliding-door right.
Trim & valences
Driver and passenger rocker trim, rocker bridges and valences.
Brackets & joinery
Ladder support, driver support, driver and passenger valence rocker brackets, and two joint plates.
Assembly & installation hardware
The product page states that all hardware necessary for assembly and installation is included. The guide lists button-head bolts, stainless washers, nylon lock nuts, carriage bolts and drilling screws.
Installation at a glance
Assembly and installation require factory trim removal, pinch-seam drilling and fastening into the rocker panel.
The lower supports bolt to factory underbody studs and the drilled pinch seam; the valence brackets also fasten to the underbody.
The guide directs starting pilot holes with a center-punch bit and metal-drilling lubricant; if necessary, deburr drilled edges and use touch-up paint to protect exposed sheet metal.
Follow the linked Transit Scout Side Steps guide for the full assembly sequence, alignment and tightening instructions.
Tools listed in the guide
- 5/32” and 3/16” hex drive keys; 7/16” and 1/2” wrenches.
- 13mm deep-well socket with ratchet; additional socket sizes/types listed in the guide may be used if preferred.
- Impact wrench with 3/8” hex socket; pronged pry tool.
- The drilling steps also call for a drill, center-punch bit, metal-drilling lubricant, an 11/32” bit and permanent marker; deburring tool and touch-up paint if necessary.
Assembly sequence from the guide
- Remove the plastic rocker trim with a pronged pry tool; if keeping it, work slowly and release one section at a time.
- Preassemble the toe kicks and platforms. The driver platform and toe kick are shorter than the passenger parts; leave play in the rocker-trim connections for front-to-back adjustment.
- Mark and drill lower-support pinch-seam holes, avoiding spot welds; align support slots with the drilled holes before tightening the factory-stud connections.
- Fit the driver valence, ladder support, rocker bracket, rocker bridge and driver support, following the support-position rules in Fitment.
- Bolt the platforms to their lower supports and connect the driver rocker trim. Adjust the driver platform front to back before fully tightening the Step 04 hardware.
- Connect the passenger bridge, rocker trim and sliding-door platform; open the sliding door for carriage-bolt access and tighten the Step 07 hardware as shown.
- Join the passenger and sliding-door platforms; align the bottom flange edges before tightening and adjust incrementally as needed.
- Attach the passenger valence and underbody bracket, then secure the ladder support to the rocker panel with the two drilling screws.
Lead Time
Read Vanspeed lead time policy on WNDR BuiltWarranty
Read Vanspeed warranty policy on WNDR BuiltReturns
Read Vanspeed returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon