
Unaka Gear Co.
Transit - Rear Ladder System - Base Kit
Indexed listing. WNDR Built doesn't sell this product; the button opens unakagearco.com.
A rear-door base for a changing gear setup
Unaka’s Transit Rear Ladder System Base Kit is a mounting platform for a modular rear-door setup. Start with the base and add ladder extensions, a tire carrier, boxes or other accessories as the build changes, rather than replacing the entire system.
The integrated MOLLE panel allows gear to be installed from the front with Unaka MOLLE nuts or 3/8" carriage bolts, without reaching behind the panel or removing gear already fitted. The base is sold in separate driver-side and passenger-side versions; the passenger-side design maintains access to the door handle.
Integrated dampening
Unaka says the built-in dampening system reduces shock to protect the door.
MOLLE accessory pattern
The panel uses what Unaka describes as a universal MOLLE pattern for mounting accessories.
Visibility-conscious layout
Unaka says the layout is designed to minimize taillight interference, keep the license plate visible and avoid triggering backup sensors.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Unaka Gear Co.
2015+ Transit 150/250/350, 130"/148"/148" EXT, Mid/High Roof
Choose the rear-door side
Unaka offers two separate base-kit variants.
DRIVER SIDE
- Base kit for the driver-side rear door.
PASSENGER SIDE
- Base kit for the passenger-side rear door; the product page says the design maintains door-handle access.
Rear-door opening limit
Tabbed hinges reduce door opening to less than 180 degrees to prevent attached gear from hitting the van’s side.
Door drilling required
The driver-side manual requires a 3/16" pilot and 3/8" drilling through the specified door layers, then a 23mm outside opening with the supplied step bit. Clean and seal exposed metal.
Driver-side fourth mount
The driver-side installation replaces the factory door-stop fitting with a fourth-point standoff and damper; the factory door stop and the standoff use left-hand threads.
Two-person frame mounting
The driver-side manual requires two people to lift and attach the frame to the hinge brackets.
Accessories sold separately
The upper ladder extension is sold separately; the tire carrier and other listed additions are accessories to the base system.
Front-mounted gear
The MOLLE panel accepts Unaka MOLLE nuts or 3/8" carriage bolts for front-side gear installation.
Before use & maintenance
Unaka requires an initial torque check after 4 to 7 days, a follow-up after 1 month, checks every 3 to 4 months, and checks after moderate driving on bumpy or gravel roads.
Specs, parts & installation
Accessory attachment
| Panel pattern | MOLLE |
|---|---|
| Front-side fastener option | 3/8" carriage bolts or Unaka MOLLE nuts |
| Door travel | Less than 180 degrees once installed, per Unaka |
What’s in the box
Base kit
Selected driver-side or passenger-side rear ladder system base kit with integrated MOLLE panel and dampening system; a step drill bit is included.
Driver-side manual component list
Driver-side frame, upper and lower hinge brackets, upper support bracket assembly, inside bracket, third-mount pad, main boss, rubber dampener, sealing washers, fourth-point bracket/standoff/rubber damper, and mounting fasteners.
Installation at a glance
Two people are required to lift and attach the driver-side frame.
The saved manual covers the driver-side base kit: drill the third mounting point, loosely fit the hinge brackets and fourth-point components, then attach and align the frame before final tightening. It recommends fitting an optional upper ladder extension before bolting the base kit to the van.
Unaka recommends professional installation or following its detailed manual.
For the driver-side kit, torque the hinge hardware to 15 ft lbs; do not torque the third-point hardware, which is tightened only until the rubber seals/bosses compress slightly.
Driver-side assembly sequence
- Use the support pad and the manual’s measurements to mark the third mount, drill the specified layers and outside opening, then clean and seal bare edges.
- Loosely attach upper and lower hinge brackets using the factory bolts. Remove the door-stop cover and left-hand-threaded factory stop, then install the fourth-point standoff, damper and bracket.
- With two people, loosely mount the frame to the hinge brackets and fourth-point bracket, then add the third-point hardware.
- Follow the manual’s interior door-handle/inside-bracket fastener steps before final alignment.
- Center the main boss in the 23mm opening, progressively snug the hinge, third- and fourth-point fittings, then torque hinge hardware to 15 ft lbs. Do not torque the third-point hardware; tighten only to slightly compress its rubber seals/bosses.
Driver-side tools listed
- Drill, 3/16" and 3/8" drill bits, marker, tape measure, file, sandpaper and paint-cleaning/prep materials. The step bit is supplied.
- 7/32", 6mm and 4mm Allen tools; 9/16", 10mm and 12mm sockets, socket extensions, crescent wrench and a torque wrench (15 ft-lbs). The door-stop cover is removed with a trim tool.
Lead Time
Unaka’s Shipping Information page excludes oversized items from free shipping; its Shipping policy also excludes items shipped by LTL freight. For international orders, Shipping Information invites contact if checkout shows no shipping method, while Shipping policy says no displayed option means the country is not served.
This product
The product-page banner advertises free shipping on large Unaka products to the Lower 48; the brand’s oversized-item and LTL exclusions still appear in its policy pages.
Warranty
Unaka’s Refund policy covers workmanship and material defects for the original purchaser for the product’s production lifetime on Unaka-designed and fabricated parts, excluding third-party components, wear parts and modification or misuse; coatings are covered for up to 180 days after purchase.
Read Unaka Gear Co. warranty policy on WNDR BuiltReturns
The Refund policy’s Returns section allows refunds within 30 days of invoice, with a minimum 10% restocking fee if the customer covers shipping or 20% if forgoing shipping costs; its Terms & Conditions of Sale instead states 15 days after receipt and a 15% fee. Returns require an RMA, new condition, original packaging and prepaid freight; custom, electronic, discontinued and specially priced items are excluded, and the Terms & Conditions also excludes opened or installed parts.
Read Unaka Gear Co. returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon