
The BugWall
Ford Transit Side Door Screen
Indexed listing. WNDR Built doesn't sell this product; the button opens thebugwall.com.
An insect screen that rolls up or unzips for storage
The BugWall side sliding door screen uses No-See-Um bug netting on marine canvas to provide an insect barrier at the open doorway. It is offered with a magnetic closure for walking in and out or a zipper closure.
Zippers on both sides let the screen roll up; rolled flaps are secured with built-in buckle straps. Zipper across the top lets you remove the rolled-up screen for seasons when insect protection is not required (listed as new for Bug Wall V2).
Weighted bottom
Foam along the bottom adds weight for a better roll-up (listed as new for Bug Wall V2).
Entry position choices
The maker offers Center, Opening closer to FRONT of van and Opening closer to REAR of van options to suit where you walk through the doorway.
UV stability
The BugWall states the screen is UV stable.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by The BugWall
- Ford Transit, 2015+ · High, Mid or Low roof · Side sliding door.
Choose your roof height
Select the roof height for your Ford Transit.
High
- High roof
Mid
- Mid roof
Low
- Low roof
Choose your opening location
Choose the location where you typically walk in and out; this sets where the magnet strip is. If cabinetry in the sliding door opening makes you enter and exit closer to the front of the van, choose closer to the front.
Center
- Center opening option
Opening closer to FRONT of van
- Front opening option
Opening closer to REAR of van
- Rear opening option
Choose your closure
The maker selector offers both closure types with every roof height and opening-location option.
Magnet
- Magnetic closure for walking in and out.
Zipper
- Zipper closure.
Rear screen sold separately
The rear door is sold separately.
Position and tension
The installation guide requires checking screen length and side-to-side position. Keep the left zipper clear of the weather seal and center the top between the left seal bump-out and the right edge of the door. Do not install a magnetic screen too tight: excessive side-to-side tension prevents the magnet strip from operating correctly.
Trim before closing the door
The guide warns not to shut the sliding door before trimming excess screen material because it could get caught.
Available combinations
All 18 pairings exist: High, Mid or Low roof × Center, Front or Rear opening × Magnet or Zipper.
Specs, parts & installation
Construction
| Materials | US made marine canvas with No-See-Um bug netting and USA made marine grade zippers. |
|---|---|
| Made in | The BugWall states it manufactures its screens in Conway, SC. |
What’s in the box
Screen and attachments
Side sliding door screen with built-in buckle straps for securing rolled-up flaps; installation clips, including thick clips for the top, as described in the installation guide.
Installation extras
Roll of double-sided tape (the installation guide says all van screens currently ship with one). Bugwall coozie (the installation guide says one was included in the package).
Installation at a glance
The screen attaches under the weather seal with metal clips and double-sided tape; the maker states no drilling or permanent vehicle alterations are needed. Screen fabric must be trimmed to finish the installation.
Follow the updated written instructions; the older videos are visual guides only. Follow any supplemental instructions supplied with the screen as well.
For Transit vans, the guide recommends removing the plastic step if it can be removed without difficulty; if the step is blocked in, follow the video for that area.
Before reinstalling the weather seal, pinch it back shut, then seat it fully around the corners and check it with a mallet.
Position the screen
- Mark the weather seal position on the van with a marker before removing the seal across the top of the opening.
- Clean the flange with alcohol or water. Apply double-sided tape across the top and around both corners, starting and ending just below the corners, with half on each side of the flange; remove the red tape cover.
- Align the sliding-door screen guideline with the edge of the upper flange. This sets the screen to hang in front of the step/floor; do not set it lower. Raise it above the guideline if you want it at or just above the floor.
- If the screen has no guideline, initially hang it about an inch too long, as the guide says wrapping the fabric around the flange and reinstalling the seal raises it about an inch.
- Stick the backside of the fabric first and wrap it around the flange, leaving room behind the corners so the seal can be fully reinstalled.
Clip, trim and reseal
- Use the thick clips across the top over the fabric and tape. Start with one in the center and one toward each side; check length before adding more because the clips are difficult to remove.
- The guide says the weather seal and working down the sides lift the screen about another 1/4" or so. Once length looks right, place a clip about every 6-8" across the top.
- Add clips just below and in the turn of each corner; a small hammer or mallet can help seat them. Recheck length.
- Wrap the fabric around the flange down the sides, using clips that fit the metal thickness. The guide suggests relief cuts in the fabric at the left-side bump-out. Keep the zipper straight and reinstall the side seal as you go.
- Once satisfied with position, trim excess material. The guide recommends scissors over a razor to reduce the risk of injury or scratching the van.
- Pinch the seal back shut before reinstalling it across the top and corners, align the reference marks and use a mallet to ensure the seal is seated tightly.
Source notes
- The BugWall product page describes the zipper closure as centered, but its offset-option paragraph says the magnet/zipper opening is approx. 14" from the edge of the door opening; the position of the zipper on offset variants remains unconfirmed.
- The BugWall buy selector offers Front + Zipper and Rear + Zipper for High, Mid and Low roofs; the option combinations here follow that selector, without treating the offset zipper position as established.
Lead Time
Lead times vary; contact the maker. Product banner: about 1 week to shipment for new orders; international taxes, fees, duties and tariffs are the buyer’s responsibility.
This product
The banner on The BugWall product page estimates 1 week until shipment from the shop for new orders due to high demand.
Warranty
Read The BugWall warranty policy on WNDR BuiltReturns
Returns within 30 days; later returns incur a 25% fee and are not accepted after 90 days.
Read The BugWall returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Owner reports
Quotes from owners and installers, with links to where they were posted. These are owner reports, not manufacturer-confirmed information, and may describe a different van or year than yours. Verify before you buy.
They have held up well after three years, and work great.
View originalHave it installed on side slider and rear doors.
View originalVery effective when you want a ventilating breeze and the bugs are out to get you.
View originalI was traveling, away from home, and they worked with me to make sure it arrived where I was currently staying before hitting the road again.
View originalI added some horseshoe zippers to access my windows so I can leave the screens down when the doors are closed.
View originalI have an Aussie that goes with us everywhere. He is around 60lbs and he goes in and out thru the bugwall screen with no issue. 3 years later the screen is holding up great.
View originalSearches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon