
Outside Van
Sprinter Van Spare Tire Carrier
Indexed listing. WNDR Built doesn't sell this product; the button opens shop.outsidevan.com.
Under-chassis storage for a larger spare
Outside Van’s spare tire carrier stores an upgraded spare wheel and tire beneath the Sprinter chassis. The rack uses an adjustable shackle mount to accommodate a larger-diameter spare while keeping it in an under-chassis position.
The carrier replaces the factory rack and reuses the van’s factory shackle brackets and original mounting hardware. Its center section has slotted holes that allow it to be raised for different tire sizes. Once the spare is in place, the rack lifts and latches like the factory carrier, with the factory hanger bolts used to snug the tire into position.
Aluminum construction
The carrier is aluminum with a black powder-coated finish.
Adjustable center section
The center bracket’s slotted holes provide height adjustment for different tire sizes.
Factory-style latching
The carrier lifts and latches like the factory rack.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Outside Van
- Mercedes-Benz Sprinter 2500 chassis, 4WD and 2WD.
- The installation guide covers 144/170 wheelbase configurations.
Conditional drill-bit clearance
Before mounting, check that the bolts slide through the shackle. If they do not, the guide calls for a 1/2” drill bit to clear extra powder coat.
Shackle tightening
Do not overtighten the ½” bolts: snug the nyloc nuts to the washers without crushing the shackle.
Tow-hitch clearance
The spare must not contact the tow hitch when the factory hanger bolts are tightened.
Tire size
Outside Van lists fitment for tires up to 32" with the adjustable shackle mount.
Factory mounting equipment
Installation reuses the factory shackle brackets, original bracket hardware, factory hooks and factory hanger bolts.
Wheelbase-specific mounting
For the 144 Sprinter, use the top two holes on the three-hole shackle bracket and the top holes on the carrier. For the 170 Sprinter, use the lower two holes on the bracket and the lower holes on the carrier.
Specs, parts & installation
Construction
| Material | Aluminum |
|---|---|
| Finish | Black powder coat |
What’s in the box
Carrier brackets
One driver-side bracket, one passenger-side bracket and one center bracket.
Mounting hardware
Outside Van states that all necessary mounting hardware is included; the guide lists bolts, nyloc nuts and washers.
Installation at a glance
Outside Van recommends two people when lifting and latching the loaded carrier because of the added weight.
Before assembly, inspect the components for finish or craftsmanship defects and check that all necessary hardware is present.
Remove the factory spare and rack, assemble the new carrier, and reinstall the factory shackle brackets in the wheelbase-specific positions. Start the adjustable center section at its lowest position.
Push the spare as far forward in the carrier as possible and lower the factory hooks to their lowest position before lifting and latching. Tighten the factory hanger bolts until the tire is snug, then replace the bolt covers.
Tools listed in the guide
- One flat-blade screwdriver.
- Two 13mm open-end/socket wrenches.
- One 19mm open-end/socket wrench; Step 1 also allows the lug wrench from the vehicle tool kit.
- Two 3/4” open-end/socket wrenches.
- Two 1/2” open-end/socket wrenches.
Factory rack removal
- Open the rear doors and pry off the bolt covers with a screwdriver.
- Unscrew the exposed hanger bolts counter-clockwise by approximately 20 turns, unhook the catches and lower the factory carrier. Remove the spare.
- Remove the four spare-mount bolts and retain the factory shackle mounts for reuse.
Source notes
- Outside Van’s installation guide hardware table lists 1/2”-20 X 3 3/4” bolts, while Step 5 specifies 1/2”-20 X 3 ½” bolts; bolt lengths are omitted here.
- The guide’s hardware table lists 5/16”-24 X 1 1/4” bolts and 5/16”-24 nyloc nuts, while Step 3 specifies 5/16”-18 X 1” bolts and 5/16”-18 nyloc nuts; these conflicting fastener specifications are omitted here.
- The hardware table assigns the 1/2” hardware to Step 3 and the 5/16” hardware to Step 5, while the installation steps use them in the opposite order.
Lead Time
Read Outside Van lead time policy on WNDR BuiltWarranty
Read Outside Van warranty policy on WNDR BuiltReturns
Shop products: return eligible unused items within 30 days of purchase; customers pay return shipping.
Read Outside Van returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon