
VANNON
VANNON Running Rails V1
Indexed listing. WNDR Built doesn't sell this product; the button opens vannon.com.
Step rails for both sides of a Sprinter
VANNON’s Running Rails V1 provide driver- and passenger-side step surfaces for getting into and out of a Sprinter. Their low-profile shape sits along the sides of the van, with anti-slip traction surfaces for footing.
The rails use aluminum construction with a crinkle black powder coat. Stainless steel mounting hardware secures the set; the maker’s installation guides describe rivnut mounting and bracing.
Traction surfaces
Anti-slip traction step surfaces are provided on both sides.
Low-profile rails
The running rails use a low-profile design.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by VANNON
Mercedes-Benz Sprinter 144" and 170" wheelbase models, 2008 and newer.
Factory rooftop A/C excluded
Not compatible with models that have factory rooftop A/C systems.
Custom-build availability only
VANNON says Running Rails V1 are no longer available for direct purchase and are exclusively offered as part of custom VANNON builds.
Drilling & undercoat trimming
Both guides require drilling and trimming factory undercoat at mounting spots; the passenger-side guide also requires drilling the rail for brace attachments.
Installer & safety requirements
VANNON strongly recommends installation by a certified mechanic and recommends 2 people. Read and follow all instructions and warnings before installation, and always use safety equipment.
Modification limits
The guides say not to add, alter or fabricate factory or aftermarket parts to increase vehicle height over the intended height of the VANNON product; mixing component brands is not recommended.
Specs, parts & installation
Construction & finish
| Rails | Aluminum |
|---|---|
| Finish | Crinkle black powder coat |
| Mounting hardware | Stainless steel, per the product page |
| Origin | Made in the USA, per VANNON |
What’s in the box
Step rails
Driver-side step and passenger-side running rail.
Driver-side hardware — guide list
- 6 x ¼-20 rivnuts
- 6 x washers
- 6 x ¼-20 bolts
Passenger-side braces & hardware — guide list
- 3 x brace arms
- 11 x ¼-20 rivnuts
- 14 x washers
- 14 x ¼-20 bolts
- 3 x ¼-20 nuts for thru-bolts from brace arms to the step
Installation at a glance
Drilling is required on both sides; VANNON recommends trained professionals and 2 people.
Dry-fit the rails, trim factory undercoat at mounting spots and check that the rails sit flat against the upper frame.
Install rivnuts and mounting hardware as shown in each guide; the passenger-side rail also uses 3 brace arms.
Use blue threadlocker and safety equipment.
Tools listed in the guides
- Protective eyewear, Sharpie and utility snap-off knife.
- Drill, rivnut tool, 7/16” socket and 25/64” drill bit for rivnuts.
- Blue threadlocker.
- Passenger-side guide additionally lists a 1/4” drill bit and 1 friend.
Driver-side mounting sequence
- Dry-fit the step, trace mounting points, trim undercoat and check that the step sits flat against the upper frame.
- Mark and drill the upward-facing holes using a 25/64” bit; install rivnuts and temporarily fasten the step.
- With the two upward-facing bolts fastened, mark two horizontal-facing holes on each side.
- Remove the upward-facing bolts, drill the 4 remaining holes with the 25/64” bit, install rivnuts and fasten all hardware using blue threadlocker.
Passenger-side mounting sequence
- Dry-fit and trace the rail, trim undercoat and check that it sits flush along its entire length against the upper frame.
- Have one person hold the rail while marking the two outer upward-facing holes; drill with a 25/64” bit and install rivnuts.
- Temporarily mount the rail to mark the two inner upward-facing holes, remove it and install two more rivnuts.
- Temporarily tighten the four upward-facing bolts, then mark and drill the horizontal-facing holes with the 25/64” bit and install rivnuts.
- Reinstall the rail with washers and 1/4-20 hardware; do not fully tighten until all bolts are installed. If rivnuts are not centered, the guide allows the rail mounting holes to be enlarged.
- Test-fit all three brace arms and mark their rail and frame attachment points; install rivnuts on the vehicle frame.
- Drill 1/4” holes through the rail for the braces and attach them with the supplied bolts, washers and nuts.
- Fully tighten all hardware using threadlocker.
Lead Time
VANNON excludes running rails from its select-order free continental-U.S. shipping promotion.
This product
VANNON’s product page marks Running Rails V1 “Pick up Required”.
Warranty
Read VANNON warranty policy on WNDR BuiltReturns
Qualifying returns must reach VANNON within 30 days of purchase; a 20% restocking fee per package and customer-paid return shipping apply.
Read VANNON returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon