
The BugWall
Sprinter Rear Screen V2 - Full Insect Bug Screen
Indexed listing. WNDR Built doesn't sell this product; the button opens thebugwall.com.
A rear-door insect screen that rolls up or removes
The BugWall Sprinter Rear Screen V2 puts no-see-um bug netting across the rear doorway for insect protection. Marine canvas surrounds the netting, with a choice of magnetic or zipper closure at the center for entry and exit.
Side zippers let you roll the screen up and secure it with built-in buckle straps when you want it out of the way. A separate zipper across the top lets you remove the rolled-up screen for seasons when insect protection is not needed.
Foam lower edge
The V2 adds foam along the bottom; The BugWall says this adds weight and improves roll-up.
Marine-grade zippers
Marine-grade zippers run along both sides of the screen.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by The BugWall
- Mercedes Sprinter high-roof rear door · 2007-2018
- Mercedes Sprinter high-roof rear door · 2019+
Choose your center closure
Both closure types are offered for each year range.
Magnet
- Magnetic center closure for walking in and out.
Zipper
- Zipper closure at the center.
Magnetic-screen tension
Do not install a magnetic screen too tightly side to side: The BugWall warns that excess tension prevents the magnet strip from operating correctly.
Check installation before starting
The BugWall does not accept returns after an installation attempt solely because the buyer cannot install the screen; review the instructions first.
Year selection
Select the matching Year Range: 2007-2018 or 2019+.
Specs, parts & installation
Screen construction
| Materials | Marine canvas and no-see-um bug netting |
|---|---|
| Zippers | Marine-grade side zippers and a top removal zipper |
| Lower edge | Added foam |
| Manufacture | Made in the USA |
What’s in the box
Screen
Rear screen with built-in buckle straps.
Installation supplies
Double-sided tape and installation clips, as described in The BugWall’s written installation instructions.
Accessory
BugWall coozie, as listed in the installation instructions.
Sold separately
Side sliding-door screen.
Installation at a glance
Install beneath the door weather seal, using tape across the top and clips down the sides.
For Sprinter rear screens, do not install clips across the top: use only the tape there, held by the reinstalled seal; the first clip goes below the upper corner.
Align the rear-screen latch holes, slots or cuts with the rear-door latches to set its height. Fit and check the screen before trimming excess fabric. Pinch the weather seal back shut before reinstalling it.
Follow the updated written instructions and any supplemental instructions supplied in the package; use the older videos only as a visual guide.
Position and attach
- Mark the weather seal’s original position before removing it across the top of the opening.
- Clean the flange with alcohol or water. Apply the double-sided tape across the top and around both corners, with half on the front and half on the back of the flange.
- Position the screen with enough fabric behind the flange to reinstall the weather seal fully into the corners.
- Work down the sides, wrapping the fabric around the flange and using clips suited to the metal thickness. Keep the zippers straight; relief cuts in the fabric can help it follow the bump-out.
Trim and finish
- Once satisfied with the fit, trim off excess fabric. The BugWall recommends scissors rather than a razor to reduce the risk of scratches or injury.
- Pinch the seal back shut, then reinstall it at the reference mark and fully into the corners. The instructions call for going back over the seal with a mallet to ensure it is seated.
Source notes
- The BugWall’s Sprinter Rear Screen V2 product description says “Fits Sprinter High Roof REAR door”, while the same page’s Roof Height selector offers High and Low; Low-roof fitment remains unconfirmed, and the fitment text follows the narrower high-roof statement.
- The maker’s selector offers all eight combinations of High or Low roof, Magnet or Zipper center closure, and 2019+ or 2007-2018; those options are retained without treating Low-roof fitment as confirmed.
- The BugWall’s shipping policy says lead times vary and to contact it for current timing; the product-page banner estimates 1 week until shipment for new orders.
Lead Time
Lead times vary; contact the maker. Product banner: about 1 week to shipment for new orders; international taxes, fees, duties and tariffs are the buyer’s responsibility.
This product
The maker’s product-page banner estimates 1 week until shipment for new orders.
Warranty
Read The BugWall warranty policy on WNDR BuiltReturns
Returns within 30 days; later returns incur a 25% fee and are not accepted after 90 days.
Read The BugWall returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon