
nVader Equipment
UpDog Rear Step
Indexed listing. WNDR Built doesn't sell this product; the button opens flarespace.com.
A steel step for rear access
The UpDog Rear Step provides a stepping surface for getting in and out of the rear of your Sprinter. It attaches to the factory trailer cross member, rather than mounting through a rear door.
The step is formed from steel plate with a matte black powder-coat finish. Its mounting arrangement uses side and top fixing points; the maker states that it works with the factory sensors.
Steel construction
The stepping surface is made from steel plate with a powder-coat finish.
Factory-sensor compatibility
The maker states that the step works with the factory sensors.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by nVader Equipment
2019+ (VS30) Mercedes Sprinter 2500 vans.
Supplied hardware only
The installation guide requires using only the supplied hardware; substituting or modifying hardware could damage the vehicle.
Mounting location
Attaches to the factory trailer cross member.
Specs, parts & installation
Construction
| Material | 3/16” steel plate |
|---|---|
| Finish | Matte black powder coat |
What’s in the box
Rear step
(1) UpDog Rear Step.
Side mounting hardware
(2) ½" #13 bolts, 1.5" long; (4) ½" washers; (2) ½" #13 Nylock nuts.
Top mounting hardware
(1) ¼" #20 bolt, 1" long; (2) ¼" washers; Nylock nut.
Installation at a glance
Attaches to the factory trailer cross member using side and top fixing points.
Remove an existing step if applicable, then align the two side holes and one top hole.
The guide strongly recommends safety glasses and notes that the fastener work can be completed from underneath the vehicle.
Tools listed in the guide
- Socket and wrench set with ¾" and 7/16" sockets.
Mounting sequence
- Remove the existing step, if applicable.
- Position the UpDog Step with the two side holes and one top hole aligned.
- Insert the two ½" #13 X1.5" bolts into the right-hand side holes. Use a washer on the bolt side and nut side of each bolt, attach the ½" Nylock nuts and hand-tighten.
- Insert the ¼" #20 X 1" bolt into the top hole with washers on the bolt and nut sides; hand-tighten the nut.
- The guide specifies a 7/16" wrench and socket for the ¼" bolt and nut, and a ¾" socket and wrench for the ½" bolts.
Source notes
- The UpDog product description says “All hardware included.” Its installation block says “Hardware NOT Included.” The UpDog installation guide lists supplied mounting hardware; this listing follows the guide.
- The UpDog installation guide parts list (page 3) specifies a ¼" Nylock nut for the ¼" #20 top bolt; step 4 (page 5) instead specifies a ½" #13 Nylock nut. The disputed top-nut size is omitted from the parts and installation copy.
- The UpDog product-page installation block links a Starlink Roof Rack Mount video, not an UpDog installation video; this listing links the product-specific UpDog PDF instead.
- Flarespace’s Refund Policy and Terms & Conditions page say all sales are final; the UpDog product-page footer allows case-by-case return evaluation for other products and deducts shipping and a 4% processing fee.
Lead Time
Read nVader Equipment lead time policy on WNDR BuiltWarranty
nVader exterior products: 1-year limited warranty for the original purchaser; proper installation required.
Read nVader Equipment warranty policy on WNDR BuiltReturns
Flarespace purchases: cancel within 24 hours; non-fiberglass returns assessed case by case; refunds deduct shipping costs and a 4% processing fee; faulty products replaced at no cost.
This product
The UpDog product-page footer allows cancellation within 24 hours and case-by-case evaluation of other non-fiberglass, non-bedding products for return or exchange; refunds exclude shipping and a 4% processing fee.
What are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon