
Avatar Massif – Van Rear Door Storage Mounting System
Indexed listing. WNDR Built doesn't sell this product; the button opens avataroffroad.com.
A rear-door platform for modular storage
The Avatar Massif turns a van’s rear door into an exterior mounting platform for storage boxes, Rotopax, tools and other gear. Pre-drilled holes and slotted rails provide attachment points for arranging a storage setup outside the living space, rather than carrying those items inside the van.
The platform works with all Avatar storage boxes and can accept a Massif tire carrier or bike-carrying accessories. Its horizontal crossbars also serve as ladder rungs for roof access. The TIG-welded aluminum frame has a black powder-coat finish; the mounting layout leaves space for additional drilled, tapped or bolted accessory attachments, as described in Avatar’s VS30 guides.
Two mounting directions
Vertical and horizontal mounting slots accommodate accessory placement in both directions.
Hinge-point mounting
On the VS30, brackets connect the platform to the rear-door hinge points and a center attachment.
Accessory choices
The maker offers MOLLE panels, a Massif spare tire carrier and bike posts as selectable add-ons.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Avatar Offroad
- Mercedes Sprinter VS30 907
- Mercedes Sprinter NCV3 906
- Ram Promaster
- Ford Transit (High Roof)
- Nissan NV (High Roof)
- Nissan NV (Low Roof)
Choose the door configuration
Select the vehicle-specific platform and door position from the maker’s options.
Driver
- Driver-side rear-door configuration.
Passenger
- Passenger-side rear-door configuration.
Both Doors
- Driver and passenger rear-door configurations.
Door position
Driver, Passenger and Both Doors options are available for every vehicle option.
Available combinations
Sprinter VS30 907 and Ford Transit (High Roof or Low Roof) offer Driver, Passenger or Both Doors with either 270 Degree or 180 Degree. Sprinter NCV3 906, Ram Promaster and Nissan NV (High Roof or Low Roof) offer all three door choices with the 270 Degree selector value only.
Hinge selection
Avatar says hinge degree applies only to Transits and VS30s, not NCV3s or Promasters. For Sprinter vans 2019+, Avatar highly recommends swapping to 180 hinges.
VS30 driver attachment
The VS30 driver guide requires drilling the door with the provided 3/8” drill bit and setting plus nuts for the center attachment.
VS30 passenger attachment
The passenger guide calls for removal of the Mercedes badge and securing the center bracket at the badge location.
Installer requirement
Avatar recommends professional installation. If you have no mechanical experience and are not thoroughly familiar with the installation procedures, the guides require a professional installer or other qualified person.
Before use
Check mounting points and attachments before use and periodically inspect for wear or damage, as required by Avatar’s guides.
Specs, parts & installation
Frame & finish
| Construction | TIG-welded aluminum |
|---|---|
| Finish | Black powder coat |
| Weight | 32 lbs |
| Capacity | Avatar states 200 lbs. capacity, describing this as a guideline based on how much load the door can take. |
Mounting layout
| Vertical rail mounting | Every 2in. |
|---|---|
| Crossbars and top/bottom mounting | 14in centers |
| Mounting width | 26in on center |
What’s in the box
VS30 frame & brackets
The VS30 guide box diagrams show the Massif frame, upper and lower hinge brackets, the side-specific center bracket, hinge spacers and a circular template.
VS30 mounting hardware
Both VS30 guide hardware pages list six 3/8-16 x1 SS Allen bolts, six 3/8-16 Nyloc flange nuts, four 3/8-16x1 SS carriage bolts, four 3/8 push nuts, four 3/8-16 serrated flange nuts, an upper hinge top bolt spacer and Loctite.
VS30 driver drilling supplies
The driver guide additionally lists two 1/4-20 plus nuts, a 3/8 drill bit, a plus-nut setting tool and a 1/4-20x1.25 flanged hex bolt.
Installation at a glance
The VS30 guides call for a partner to help lift and support the Massif during mounting.
Use the guide or video for the selected vehicle and door side. The written guides below cover VS30 driver and passenger installations; separate maker videos cover NCV3, Promaster and Transit.
Attach the upper, lower and center brackets to the frame, prepare the hinge bolts and spacers, then lift the frame onto the door with a partner. Secure the center bracket before final tightening.
The VS30 driver guide requires drilling and plus-nut installation; the passenger guide starts with Mercedes badge removal.
VS30 hinge-mount sequence
- Install the wider section of each bracket toward the Massif and the narrower section toward the hinges.
- Place the square spacer on the upper bolt of the upper bracket only; the push nuts are optional installation aids.
- Open the door 90° for mounting and have a partner support the Massif while the bolts pass through the hinge holes.
- Place the eyeglass-shaped spacer at the upper hinge, narrow section inward, and the rectangular spacer at the lower hinge.
- Apply the provided Loctite to the four nuts and leave the hinge fasteners short of final tightening until the center bracket is secured.
VS30 driver plus-nut preparation
- Use the guide’s template to locate the holes before drilling with the provided 3/8” bit.
- Set the plus nuts with the setting tool and an impact; wear a glove when holding the setting tool and do not overtighten.
Source notes
- Avatar’s captured product-page title says “No Drill”; its VS30 driver installation guide requires drilling with a 3/8” bit and setting plus nuts. This listing follows the guide.
- Avatar’s live vehicle selector offers Ford Transit (Low Roof) and Ford Transit (High Roof), while its Specs block lists Transit Mid/High Roof. The fitment summary uses the shared High Roof scope; the option combinations follow the live selector.
- The VS30 passenger guide’s hardware page lists Avatar Badge, but its installation step calls the badge optional and Avatar’s product page sells it as an add-on. Badge inclusion is not asserted here.
- The VS30 passenger guide’s hardware page lists two 1/4-20x1 serrated flanged hex bolts, while its badge-installation step specifies M6-1.0 bolts. The disputed center-attachment fasteners are omitted from the hardware list above.
- The VS30 driver guide’s hardware page presents Avatar Badge OR Half Moon Spacer x1 & 14x1 Screw x2; the product page sells the badge as an add-on. Neither alternative is promised as an included item here.
- The VS30 driver guide’s opening tool list names a 7/32 Allen key, while bracket assembly calls for a 1/4 Allen. The inconsistent tool size is omitted from the installation summary.
Lead Time
Larger or heavier items requiring LTL must ship to a business address or shipping terminal; domestic shipping uses USPS or FedEx, with charges calculated at checkout.
This product
Avatar’s Massif page advertises free shipping for the Lower 48 and specifies a business address or nearest terminal.
Warranty
Read Avatar Offroad warranty policy on WNDR BuiltReturns
Returns generally cover only damaged or defective products; exceptional returns require approval, unused condition, tags, original packaging, purchase proof, customer-paid return shipping and a 20% restocking fee.
Read Avatar Offroad returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon