
Aluminess
Recon Front Winch Bumper - 2019-26 Sprinter
Indexed listing. WNDR Built doesn't sell this product; the button opens aluminess.com.
A low-profile bumper built around a steel winch cradle
The Aluminess Recon front winch bumper combines an aluminum outer skin with a steel winch cradle that mounts to the vehicle chassis. It is intended to add front-end protection and off-road equipment mounting while keeping a low-profile, stock-like appearance. The textured black powder-coated finish covers the aluminum skin.
The cradle supports the bumper, with a hitch receiver mounted beneath it. The design brings winch mounting, recovery points and light-mounting provisions into the front bumper rather than treating them as separate exterior mounts. An optional bull bar adds grille protection and another location for lights or accessories.
Recovery connections
An integrated 2” hitch receiver accompanies recovery points designed for 3/4” D-ring shackles with a 7/8” pin.
Lighting provisions
The bumper accepts Baja Designs Squadron and S1 lights, or similarly sized lights; the bull bar option accommodates 2x LP6 lights.
Factory sensors
Aluminess states the bumper works with factory ACC and parking sensors; installation relocates sensors and their wiring.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Aluminess
- 2019–2025 Mercedes-Benz Sprinter and Sprinter 1500
- 2019–2026 Mercedes-Benz Sprinter 2500, 3500 and 3500XD
- 2019–2025 Mercedes-Benz Sprinter 4500
Choose the bumper configuration
Select the configuration on Aluminess’s product page.
With Bull Bar
- Adds grille protection and accessory mounting.
- Provides mounting for 2x LP6 lights.
Without Bull Bar
- Bumper configuration without the optional bull bar.
Choose the front sensor bracket
Aluminess’s selector lists these bracket choices on the maker page.
None
- No front sensor bracket selected.
For 2025+ Vans
- Bracket option labeled for 2025+ vans.
For 2019–2024 Vans
- Bracket option labeled for 2019–2024 vans.
Cutting required
Installation requires cutting the factory plastic front bumper and the mesh in the airflow relief for winch-controller clearance. Retain the driver-side air-temperature sensor mount and bottom mounting hole in the factory plastic.
Lights replace the light grilles
The installation guide requires removing the light grilles when installing lights; lights and light grilles cannot be installed together.
Sensor verification and fastener checks
The guide requires a 15 to 30 minute drive to verify sensor operation after installation. Check bolt tightness after 100 miles, periodically thereafter and after any off-road use.
Factory vehicle configuration
Designed for factory-manufactured vehicles. Some aftermarket vehicle conversions are incompatible; establish compatibility with aftermarket accessories or vehicle modifications before purchasing.
Winch equipment
Accepts industry-standard winches and winch-mount accessories. Synthetic line and a compatible fairlead are required; roller fairleads and braided steel winch cable are not compatible.
Road and off-road suitability
Aluminess describes its products as designed for off-road vehicle use and requires the purchaser to assess vehicle and product suitability for on-road and off-road travel and review applicable vehicle codes.
Specs, parts & installation
Construction
| Outer skin | 5052 aluminum |
|---|---|
| Winch cradle | 1/4” steel |
| Finish | Textured black powder coat; Aluminess describes the finish as UV-resistant. |
| Bumper weight | 65lbs |
Connections
| Hitch receiver | 2” |
|---|---|
| Recovery-point shackle fit | 3/4” D-ring shackles with a 7/8” pin |
What’s in the box
Bumper assembly
1 front winch bumper in the selected configuration, 1 steel winch cradle and 1 steel hitch receiver. The product page lists 1 pre-installed sensor window and pre-installed driver-side and passenger-side light grilles.
Sensor retainers
The installation guide lists 3 parking sensor retainers: 2 for installation and 1 spare in case of installation damage.
Hardware and installation supplies
The guide lists mounting bolts, nuts and washers, anti-seize, thread locker, 4 adhesive zip-tie mounts and 4 8” zip ties.
Installation at a glance
Requires factory bumper removal, plastic trimming and sensor-wiring disconnection and rerouting.
The winch cradle mounts to the frame rails using factory bolts; the aluminum bumper fastens to the cradle.
Apply anti-seize to stainless hardware before assembly and thread locker where the guide specifies. Keep wiring clear of pinch points and the wheel liner inside the bumper.
Installation sequence from the Recon guide
- Remove the grille and, if applicable, the front camera; remove the factory bumper and disconnect parking-sensor, side-guard-assist and fog-light wiring as applicable. Remove the front radar sensor from its enclosure.
- Remove the stock crossmember and airflow skirt. Attach the hitch receiver below the winch cradle, then attach the cradle to the frame rails with factory bolts and thread locker. Center the cradle and torque its frame-rail bolts to OEM specifications.
- For 2019–2024 vans, locate the radar sensor in the carriage and rotate it into the 0 degree notch. Install the parking sensor retainers and route the harness through the cutouts with OEM gaskets; secure it using zip-tie mounts and zip ties.
- Cut the airflow mesh and provide clearance for the winch solenoid controller. Mark and cut the factory plastic bumper as illustrated in the guide, preserving the temperature-sensor mount and bottom mounting hole.
- Reinstall only the two driver-side parking sensors into the plastic factory bumper if applicable. Refit the factory plastic bumper loosely before mounting the aluminum bumper.
- Route the parking sensor harness through the bumper relief cuts. Fit the bumper to the cradle with the specified 1/2-13 X 1 1/2 bolts and washers, using thread locker. Adjust the bumper and evenly tighten the 1/2” hardware; step 29 specifies 75 ft-lbs.
- Reinstall the grille and attach the lower tray to the factory plastic bumper with the guide’s specified hardware. Reconnect parking, radar and temperature sensors and complete installation of the OEM plastic rivets.
Tools listed in the guide
- Ratchet with extension, sockets and wrenches: 13 MM, 14 MM, 18 MM, 3/8”, 7/16”, 1/2”, 3/4”.
- Torx drivers: T25, T30, T35, T45; torque wrench; Phillips and slotted screwdrivers; push-pin remover.
- Optional hammer and small prybar. The cutting steps call for a Dremel or cutoff wheel and painter’s tape.
Source notes
- Aluminess’s product page lists 2 parking sensor retainers; the Recon installation guide lists 3, explaining that one is a spare. This listing follows the guide.
- The Recon guide’s hardware table lists 2 fender washers, while step 31 calls for 4. The disputed washer count is omitted from the parts list.
- The product page’s Weight Info lists shipping weight as 95lbs, while Detailed Specs labels its shipping-dimensions weight 65 LBS. Shipping weight is omitted here.
- The product title and installation guide state 2019–26 Sprinter; the description says 2019-UP. Detailed Specs ends at 2025 for Sprinter, 1500 and 4500, and 2026 for 2500, 3500 and 3500XD; the trim-specific ranges are shown here.
Lead Time
Bumpers and roof racks ship by LTL freight and do not qualify for free shipping; destination charges may apply. Inspect and record shipping damage before signing.
Read Aluminess lead time policy on WNDR BuiltWarranty
Lifetime warranty for the original retail purchaser requires correct installation under official instructions; modifications void coverage; exclusions apply, and claim shipping both ways may be customer-paid.
Read Aluminess warranty policy on WNDR BuiltReturns
Authorized nondefective returns within 15 days; custom/special orders excluded; roof racks require another buyer; refunds deduct all shipping, including Aluminess-paid outbound costs, and any restoration costs.
Read Aluminess returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon