
Aluminess
Legacy Side Ladder - 2019-26 Sprinter
Indexed listing. WNDR Built doesn't sell this product; the button opens aluminess.com.
Side access to roof storage
The Aluminess Legacy Side Ladder provides a route to roof storage and rooftop tents from the side of a Sprinter. Its aluminum construction follows a shape that extends into the wheel well, with redesigned flat steps spaced evenly along the climb.
The ladder attaches at the top and at a lower body bracket rather than using a rear door as its mounting surface. The four configurations use mounting arrangements for roof tracks, an Aluminess Recon roof rack or a penthouse top; the matching installation guides set out the different attachment methods.
Accessory attachment
L-Track bow-ties provide points for securing additional accessories.
Ground clearance
Aluminess describes the ladder as a high-clearance design.
RVIA compliance
Aluminess states that the ladder is RVIA compliant.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Aluminess
- 2007+ Mercedes Sprinter, as specified in the track-mounted, Recon and Penthouse installation guides.
Choose your roof configuration
Choose the configuration matching your roof and upper mounting arrangement.
Low Roof
- Track-mounted configuration; factory or aftermarket roof tracks must be installed before the ladder.
High Roof
- Track-mounted configuration; factory or aftermarket roof tracks must be installed before the ladder.
High Roof w/ Recon Modular Rack
- Uses the Recon roof-rack brackets; the guide says this ladder only works with Aluminess’ Sprinter Roof Rack.
Penthouse Roof
- Uses upper L and S brackets fastened into the exposed roof gutter with self-drilling screws and silicone sealing.
Drilling required
All three installation guides require three ¼” holes through the pinch weld for the lower bracket. The Penthouse version also uses self-drilling screws into the roof gutter.
Penthouse sealing
Apply silicone beneath the upper brackets, seal around the brackets and screw heads, and allow it to dry completely before closing the penthouse top.
Hardware care
Apply anti-seize to bolt threads before assembly and follow the matching guide’s torque instructions; overtightening can break hardware.
California warning
Aluminess’s product page carries a warning for cancer and reproductive harm: www.P65Warnings.ca.gov.
Product-page model list
- 2007-2025 Mercedes-Benz Sprinter
- 2010-2026 Mercedes-Benz Sprinter 2500
- 2010-2026 Mercedes-Benz Sprinter 3500
- 2018-2026 Mercedes-Benz Sprinter 3500XD
- 2019-2025 Mercedes-Benz Sprinter 1500
- 2019-2025 Mercedes-Benz Sprinter 4500
Mounting position
The track-mounted and Penthouse guides place the ladder in front of the rear wheel on the driver’s side; the Recon guide specifies in front of the rear wheel.
Accessory and conversion compatibility
Aluminess lists compatibility with its nerf bars and side steps, Storyteller and Winnebago Revel conversions, and clearance for Flarespace flares.
Aftermarket conversion check
Aluminess designs its products for factory-manufactured vehicles and warns that some aftermarket conversions are incompatible; contact its customer service for compatibility questions.
Specs, parts & installation
Construction
| Material | Aluminum |
|---|
Shipping dimensions — not ladder dimensions
| Height | 13 IN. |
|---|---|
| Width | 96 IN. |
| Depth | 16 IN. |
| Shipping weight | 26 LBS. |
What’s in the box
Low Roof / High Roof mounting parts
The track-mounted guide lists two upper L brackets, one lower attachment bracket, two threaded inserts, mounting nuts, washers and screws, and one 2g anti-seize packet.
Recon mounting parts
The Recon guide lists one lower attachment bracket, left and right upper brackets, mounting nuts, washers, button-head screws, socket-cap screws and carriage bolts, and one 2g anti-seize packet.
Penthouse mounting parts
The Penthouse guide lists two upper L brackets, two S mounting brackets, one lower attachment bracket, mounting nuts, washers and screws, four #14 x 1.5” self-drilling screws, and one 2g anti-seize packet.
Installation at a glance
Use the installation guide for your selected configuration.
The upper mount attaches to roof tracks, the Recon rack or the penthouse roof gutter; the lower bracket attaches at the pinch weld.
If fitting an accompanying pair of nerf bars, the guides advise installing the ladder first.
Align the ladder before final tightening, apply downward pressure when securing it to the lower bracket, and recheck all fasteners after 50 miles. The track-mounted guide then calls for periodic checks; the Recon and Penthouse guides specify every 1000 miles afterwards.
Track-mounted installation details
- Slide the threaded inserts into the roof track from the rear with studs pointing up, then loosely attach the L brackets.
- Clamp the ladder to the L brackets and fit the upper hardware by hand before positioning the lower bracket.
- The guide specifies 6 ft-lbs. for the lower ¼” cap screws and 11 ft-lbs. for the lower 5/16” nuts. Its final upper-bolt instruction specifies 6 ft-lbs. for ¼” hardware and 11 ft-lbs. for 5/16” hardware.
Recon installation details
- Position the upper brackets along the Recon rack side rail, measure their spacing against the ladder and attach the ladder before final positioning.
- The Recon guide’s final tightening instruction says all bolts to at least 10 ft-lbs. of torque.
Penthouse installation details
- Assemble the L and S brackets at the ladder top and raise the penthouse top to expose the gutter for mounting.
- Keep the remaining S-bracket holes perpendicular to the vehicle direction for final adjustment.
- The Penthouse guide’s final upper-bolt instruction specifies 6 ft-lbs. for ¼” hardware and 11 ft-lbs. for 5/16” hardware.
Tools and installation supplies
- Track-mounted and Penthouse guides list standard and metric wrench and socket sets, a standard hex-key set, and a drill with drill bits.
- The Recon guide lists standard and metric wrench and socket sets, a flat-head screwdriver and painter’s masking tape; its lower-bracket steps also require a ¼” drill bit.
- The lower-bracket steps use C-clamps or spring clips. The Penthouse installation requires silicone.
Source notes
- Aluminess’s product title says 2019–26 Sprinter; its track-mounted, Recon and Penthouse guides each specify 2007+ Mercedes Sprinter. This listing follows the guides.
- Aluminess’s product page generally says the ladder mounts to factory or aftermarket roof rails; its Recon guide requires Aluminess’ Sprinter Roof Rack, while its Penthouse guide mounts the upper brackets into the roof gutter. This listing follows the configuration-specific guides.
- The track-mounted guide names the lower bracket as 350558 in its warranty warning and 351129 in its parts table; the bracket identifier is omitted here.
Lead Time
Bumpers and roof racks ship by LTL freight and do not qualify for free shipping; destination charges may apply. Inspect and record shipping damage before signing.
This product
Aluminess’s product page says this ladder ships free; its shipping policy limits free shipping to the contiguous 48 states, with possible rural or island shipping charges.
Warranty
Lifetime warranty for the original retail purchaser requires correct installation under official instructions; modifications void coverage; exclusions apply, and claim shipping both ways may be customer-paid.
This product
The track-mounted guide excludes threaded inserts and the lower attachment bracket for overtightening or failure to use anti-seize. The Penthouse guide excludes its lower attachment bracket.
Returns
Authorized nondefective returns within 15 days; custom/special orders excluded; roof racks require another buyer; refunds deduct all shipping, including Aluminess-paid outbound costs, and any restoration costs.
Read Aluminess returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon