
Sandy Vans
SV Sprinter Van Side Steps
Indexed listing. WNDR Built doesn't sell this product; the button opens sandyvans.com.
Solid side steps with built-in service ports
The SV Side Steps provide a flat intermediate foothold for entering and leaving a Sprinter. Aluminum plate forms a solid stepping surface rather than an open tube, and the pinch-weld mounting positions each step flush to the van body. The driver and passenger steps are supplied together.
Two built-in accessory ports provide locations for a water fill, air inlet, or power passthrough. Sandy Vans also designed the step position to work as the first rung below its Side Ladder. The steps serve daily access rather than the trail-protection role of a rock slider, and their permanent mounting requires drilling into the van.
Plate construction
The steps use 3/16″ aluminum plate with a textured black powder coat finish.
Ladder pairing
Compatible with the SV Side Ladder and most third-party side ladders.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Sandy Vans
- 2007+ Mercedes-Benz Sprinter 2500 & 3500; NCV3 (2007–2018) and VS30 (2019+).
- 144" / 170" / 170" EXT; High Roof only.
- RWD, 4x4, and AWD.
Excluded vehicles
Not compatible with Ford Transit, Ram ProMaster, or Mercedes-Benz E-Sprinter.
Permanent drilled mount
Drilling into the pinch weld is required; there is no clamp-on version. The manual also uses self-tapping screws into the van sidewall and underside support member.
Ground clearance
The maker states a 5″ reduction in van ground clearance (tube bottom to running board). The ground-to-pad figure assumes stock height; factor in any suspension lift.
Engine block heater
If the Sprinter has the optional engine block heater, it may need relocation to clear the step mount; ask Sandy Vans if unsure whether the van has one.
Sprinter-platform RVs & upfitter builds
Sandy Vans lists these Sprinter-platform builds: Winnebago Revel; Storyteller Overland (MODE, Beast Mode); Outside Van; Airstream Interstate & Atlas; Grech RV (Strada, Turismo, Terreno); Pleasure-Way Plateau; Leisure Travel Vans (Unity, Wonder); Coachmen Galleria; Midwest Automotive Designs; Jayco Terrain; Tiffin Wayfarer; Thor Tranquility. Fitment depends on the exact model, year, suspension lift, and body kit; confirm with Sandy Vans before ordering.
Side skirts & body kits
For factory side skirts or aftermarket body kits, send Sandy Vans the van year, wheelbase, and specific skirt/kit before ordering to confirm compatibility.
Specs, parts & installation
Construction & ports
| Material | 3/16″ aluminum plate |
|---|---|
| Finish | Textured black powder coat |
| Accessory ports | Two 2″ ports for water fill, air inlet, or power passthrough |
| Made in | San Diego, CA |
Step dimensions
| Step width | 6.5″ |
|---|---|
| Usable surface depth | 6¼″ |
| Ground to pad | ~13.5″ |
| Pad to slider entry | ~10″ |
| Running board to step surface | 4½″ |
| Clearance reduction | 5″ (tube bottom to running board) |
| Small step platform length | 37″ total (30″ at front face) |
| Large step platform length | 95″ total (88″ at front face) |
What’s in the box
Steps & supports
1 driver-side step, 1 passenger-side step, 7 pinch weld brackets, and 2 kicker supports.
Mounting hardware
14 each of 1/4″-20 button head screws, washers, and lock nuts; 3 each of 3/8″ bolts, washers, and lock nuts; 20 self-drilling screws.
Instructions
Printed installation manual.
Installation at a glance
Sandy Vans lists 3 to 4 hours and describes this as an involved DIY installation for someone comfortable working under a vehicle.
Position and support each step, mark the pinch-weld holes, lower the step, and drill using a 1/4″ pilot and 17/64″ bit. Bolt the brackets through the pinch weld.
Reposition and level the step with a small consistent gap, then use the self-tapping screws into the sidewall and seam brackets. Attach the kicker supports with 3/8″ hardware and self-tapping screws into the underside support member.
Repeat for the passenger step, following the manual’s bracket and support locations.
Professional installation is free with purchase at Sandy Vans HQ in San Diego.
Tools listed by Sandy Vans
- 3/8″ socket
- 11mm socket
- 14mm socket
- 14mm wrench
- 4mm Allen key
- Socket wrench
- Impact driver / drill
- 1/4″ drill bit
- 17/64″ drill bit
Lead Time
The Sandy Vans FAQ says shipping typically takes 5–7 business days, with free shipping on SV-fulfilled products.
Read Sandy Vans lead time policy on WNDR BuiltWarranty
For Sandy Vans-fulfilled products, Sandy Vans covers defects in materials or workmanship and component failure under normal use.
Read Sandy Vans warranty policy on WNDR BuiltReturns
Returns & Refunds: 30 days from delivery; Return Form: 30 days from purchase; 20% restocking and customer-paid return shipping.
Read Sandy Vans returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon