
Van Compass
REAR TUG STEP - SPRINTER (2019+) by VAN COMPASS
Indexed listing. WNDR Built doesn't sell this product; the button opens vancompass.com.
A full-width step for rear-door access
The Van Compass Rear Tug Step adds a step surface for entering and leaving through the rear doors. Its full-width, high-clearance layout is designed to address the distance between the ground and the rear entry. Van Compass says the design preserves ground clearance and departure angle.
The step also provides recovery attachment points. These connect to the towing hitch through the step’s chassis tie-in plates, giving the shackles a hitch-connected pulling point rather than making the step only an entry surface.
Steel tie-in plates
The main chassis tie-in plates are made from high-strength steel.
Removable installation
The manual states that the step can be removed to return the vehicle to stock.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Van Compass
- Mercedes Sprinter 2500 · 2019+ · All drive types
Choose your step configuration
Both maker options are black; the difference is whether D-rings are supplied.
BLACK STEP WITHOUT D-RINGS
- Black step without D-rings.
BLACK STEP WITH PAIR OF 3/4" 3.5 TON D-RINGS IN BLACK
- Black step with a pair of black 3/4" 3.5 TON D-rings.
Factory hitch and bumper required
Requires the factory Mercedes tow hitch and stock non-step rear bumper. The product page states that the step does not work with any other hitch brand.
Recovery pull direction
The manual specifies a standard 3/4” pin D-ring shackle and says to always try to pull as straight as possible when using the recovery point.
Installer requirement
Van Compass strongly recommends a certified mechanic. Anyone installing the step must read, understand and follow the instructions and warnings before installation; its warranty policy requires professional installation according to the instructions.
Parking sensors
Van Compass lists the step as compatible with parking sensors.
Specs, parts & installation
Step & construction
| Step surface width | 67" |
|---|---|
| Projection from factory plastic bumper cover | Approximately 5" |
| Projection from back of factory hitch cross tube | 8-5/8" |
| Main chassis tie-in plates | 3/8" thick high-strength steel |
| Step color | Black |
Recovery attachments
| Shackle anchor points | For 3/4" D-ring shackles |
|---|---|
| Optional supplied D-rings | Pair of black 3/4" 3.5 TON D-rings, as named in the maker’s option selector |
What’s in the box
Step & shim plates
One full-width rear hitch step and two shim plates.
Mounting hardware
Four ½-13 UNC x 1.75” GR8 carriage bolts, four ½-13 UNC stover nuts and eight 1/2” GR8 flat washers; the manual lists yellow zinc for the bolts and washers.
D-rings by option
The with-D-rings option includes a pair of black 3/4" 3.5 TON D-rings; the without-D-rings option does not.
Installation at a glance
The product page lists Recommended Shop Labor Time: 0.5 Hours; the manual lists 10-20 min for both professional shop and driveway installation.
The step bolts to the outer plates of the factory receiver hitch.
If trailer wiring is zip-tied to the outer mounting face, cut those zip ties so the step sits flush, then re-secure the wiring with a zip tie if needed after installation.
If a gap exists between the hitch and the step mounting plates, use the included shim plates between them for proper fitment.
Torque the mounting bolts to 80 ft-lbs. (109 N.m), as specified in the manual.
Tools listed in the manual
- Dykes or a similar tool for cutting zip ties.
- Rubber mallet or similar non-marring hammer or mallet.
- Basic wrench and socket set: SAE ¾”.
Mounting sequence
- Fit the step outside the hitch and align the mounting holes. If tapping it into position is needed, tap only where the thick hitch tie-in plates are welded to the step.
- Install the carriage bolts from the outside. Push the passenger-side tailpipe up by hand as far as it will go to install the forward bolt.
- Install the stover nuts with a washer under each nut. Snug the hardware using a ¾” socket or wrench.
- Keep slight upward pressure on the step while tightening so the bottoms of the chassis plates are parallel with the bottom of the hitch.
Lead Time
Van Compass allocates and ships orders on a first-come, first-shipped basis.
Read Van Compass lead time policy on WNDR BuiltWarranty
Exterior accessories are covered against defects in materials and workmanship for the original purchaser’s duration of ownership, with powder coating covered for 60 days; professional installation according to the instructions is required, and warranty labor and shipping costs are excluded.
Read Van Compass warranty policy on WNDR BuiltReturns
The Refund policy gives 30 days from purchase; Shipping, Return and Cancellation Policies gives 30 days from receipt to request authorization; unused, uninstalled returns in original packaging carry a 20% restocking fee and customer-paid return shipping.
Read Van Compass returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Owner reports
Quotes from owners and installers, with links to where they were posted. These are owner reports, not manufacturer-confirmed information, and may describe a different van or year than yours. Verify before you buy.
Has non skid tape on top and shows some rubbing from gasoline model Sprinter exhaust.
View originalSearches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon