
Aluminess
Touring Rear Step - 2019-26 Sprinter
Indexed listing. WNDR Built doesn't sell this product; the button opens aluminess.com.
A rear step with room for the factory hitch
The Aluminess Touring Rear Step provides a wider stepping area for getting into and out of a lifted van. Its aluminum step incorporates a tread pattern and drain holes, with a black powder-coated finish.
The mounting blades attach the step to the outside of the frame through the factory hitch bolt holes. This arrangement leaves the factory hitch mounted inside the frame, so the step can be fitted with or without that hitch.
Compared with its previous-generation nerf bars, Aluminess says this design sits more than 1.5” closer to the van and more than 1” higher. The Touring styling also matches Aluminess’s Touring Side Steps.
Stepping surface
A tread pattern and drain holes are incorporated into the steps.
Frame-side mounting
Mounting blades position the step outside the frame while the factory hitch remains inside it.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Aluminess
- 2019–26 Mercedes-Benz Sprinter, as named in Aluminess’s product title.
144 Dually exclusion
Not compatible with 144 Dually.
Gasoline exhaust modification
Petrol (gasoline) engines require exhaust modification for this step to be installed properly.
Support the hitch
If removing factory hitch mounting bolts, support the hitch first. The guide warns that unbolting it will allow it to fall if unsupported.
Intended use and vehicle suitability
Aluminess’s guide describes its products as designed for off-road vehicle use. Inspect vehicle and product suitability for on- and off-road travel, and review local vehicle codes before purchase.
California warning
Aluminess displays a California Proposition 65 warning: Cancer and Reproductive Harm – www.P65Warnings.ca.gov.
Factory hitch
The installation guide specifies use with or without the factory trailer hitch. Verify hitch clearance when adjusting the step.
Companion steps
Compatible with Aluminess Touring Side Steps – Sprinter 2007+.
Vehicle modifications
Aluminess designs its products for factory-manufactured vehicles; some aftermarket conversions are incompatible. Its guide does not guarantee fit with aftermarket accessories or modified vehicles; determine fitment before purchase.
Specs, parts & installation
Step construction
| Width | 67″ |
|---|---|
| Material | Aluminum |
| Finish | Black powder coat |
| Position relative to previous-generation nerf bars | Aluminess states more than 1.5” closer to the van and more than 1” higher. |
What’s in the box
Step and mounts
One nerf step and two mounting blades.
Frame mounting hardware
Eight 7/16”-14 x 4-1/2” grade 8 hex-head bolts, eight 7/16”-14 grade 8 nylon-locking nuts and sixteen 7/16” washers.
Blade mounting hardware
Six 3/8”-16 x 1-1/4” stainless steel carriage bolts, six 3/8” washers and six 3/8”-16 nylon-locking nuts.
Assembly lubricant
One 2g anti-seize bolt lubricant packet.
Installation at a glance
Aluminess’s guide requires two or more people.
The step uses the factory hitch bolt holes and the supplied mounting blades and hardware.
Apply anti-seize assembly lubricant to the threads of each bolt before assembly; stainless steel hardware can bind during tightening.
Adjust the step and hitch while verifying factory-hitch clearance. Tighten the 7/16” hardware to 50 ft-lbs.
Check mounting hardware after the first 100 miles of driving and periodically afterward for loosening from vibration.
Tools listed in the guide
- Standard and metric wrench set
- Standard and metric socket set
- Hex key (Allen) set
Mounting sequence
- Bolt both mounting blades to the step with the provided 3/8” carriage bolts, washers and nuts.
- If applicable, support the hitch and remove the eight factory mounting bolts.
- Fit the step outside the frame using the factory hitch bolt holes and supplied 7/16” hardware; the factory hitch mounts inside the frame.
- Adjust the step and hitch, verify hitch clearance and tighten the 7/16” hardware to the guide’s specified torque.
Source notes
- Aluminess’s product page describes compatibility with most receiver hitches; its installation guide specifies the factory trailer hitch, with or without it installed. This listing follows the guide.
- Aluminess’s product title lists 2019–26 Sprinter; its detailed fitment list ends at 2025 for Sprinter, 1500 and 4500, and at 2026 for 2500, 3500 and 3500XD. The linked installation guide lists 2019+ Sprinter.
Lead Time
This product
Aluminess’s product page says limited stock may mean lead times; contact Aluminess for current timing. It also states that this product ships free.
Warranty
Read Aluminess warranty policy on WNDR BuiltReturns
Read Aluminess returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon