
Agile Off Road
Telluride Winch Bumper for Mercedes Sprinter by Agile Offroad
Indexed listing. WNDR Built doesn't sell this product; the button opens agileoffroad.com.
A frame-mounted winch platform behind the bumper
The Telluride places a winch mounting plate at the Sprinter’s frame horns while retaining the contours of the factory front bumper cover. The plate leaves the radiator shroud and transmission cooler undisturbed.
Agile Offroad states that adaptive cruise, lane keep assist, the 360-degree camera and parking sensors remain operational after installation. The optional Ferrata light bar attaches directly to the winch plate behind the bumper, rather than being supported by the bumper cover.
Integrated recovery points
The winch bumper incorporates two recovery points.
Lower bumper brace
An included lower brace supports the factory bumper cover after trimming.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Agile Off Road
- Mercedes Sprinter 1500/2500/3500
- Third Generation (VS30) 2019+
Choose the vehicle version
Agile provides photos of the two Distronic sensor types on the product page to identify the matching version.
2025+ Sprinter
- Match to the product page’s 2025+ Distronic sensor photo.
2019-24 Sprinter
- Match to the product page’s 2019-2024 Distronic sensor photo.
Choose the light bar
Both light bar choices are available with either vehicle version.
Ferrata Front Light Bar
- Adds the Ferrata bar that mounts directly to the winch plate.
None
- No Ferrata front light bar.
Cutting, drilling and sensor wiring
The guide requires trimming the factory bumper cover, relocating the parking sensors, drilling their new mounting holes, and cutting and extending the parking sensor harness. Ferrata installation also requires drilling light-bar mounting holes through the bumper cover.
Recovery and lighting equipment sold separately
The winch, fairlead, flatlink and lights are not included.
Winch and light compatibility
Designed specifically for Warn 12K winches; the optional Ferrata light bar supports (2) Baja Designs LP6 / LP9 lights.
Installer requirement
Agile Offroad requires installation according to its instructions by qualified personnel and strongly recommends an authorized dealer or qualified installation center.
Specs, parts & installation
Bumper assembly
| Mounting | Winch plate mounts to the frame horns |
|---|---|
| Recovery points | (2) integrated recovery points |
| Product weight — maker product page | 50.0 lb |
What’s in the box
Bumper, covers and trim
- Telluride winch bumper
- Winch plate top cover
- Bumper brace plate
- Cutting templates
- Rubber edge trim
Sensor and wiring parts
- Distronic sensor housing
- 5 x 26” wire harness extensions with butt connectors and heat shrinks
- 37” split loom, as listed in the guide’s wiring step
Mounting hardware
- 4 x M10-1.5x35mm bolts
- 2 x 1/4” bolts
- 2 x 3/8-16x1.25 bolts
- 2 x 10-24x.75” bolts
- 6 x locating pins
- 3 x 10mm bolts
- 6 x 3/8” Allen bolts, 6 x 3/8” washers and 6 x 3/8 spacers
Ferrata option
Ferrata light bar when that option is selected.
Installation at a glance
The guide calls for a helper when lifting the winch bumper into position.
Remove the front grille, bumper cover and factory crash bumper; retain the factory mounting hardware as directed.
Use red thread locking compound at the locations specified in the guide.
Install the winch according to its manufacturer’s instructions. The Telluride guide initially uses only the 2 rear-most winch bolts; the 2 front bolts are added with the winch cover before final tightening.
Set the relocated Distronic sensor perpendicular to the ground with the vehicle level on flat ground, and reconnect the temperature sensor and front camera.
Tools listed in the guide
- Torx drivers T-25, T-30 and T-45; 3/8” Allen driver
- 10mm, 13mm and 18mm wrench/socket set
- 1-1/8”, 3/16” and 7/8” drill bits
- Panel clip removing tool, mallet, cutting tool, sander, painters tape and file
- Wire cutters, wire strippers and mini torch
- Red thread locking compound
Lead Time
Agile Offroad says orders may take 3 to 5 days to process and ship.
Read Agile Off Road lead time policy on WNDR BuiltWarranty
Agile exterior accessories carry original-owner materials/workmanship coverage for the duration of ownership; powder-coated finishes have 60-day manufacturing-defect coverage.
Read Agile Off Road warranty policy on WNDR BuiltReturns
Eligible returns: contact Agile within 90 days of purchase; a 10% restocking fee applies after 30 days, and customers pay return shipping.
Read Agile Off Road returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon