
Van Compass
REAR HITCH STEP - SPRINTER 1994-2018 2500 by VAN COMPASS - (CLOSEOUT)
Indexed listing. WNDR Built doesn't sell this product; the button opens vancompass.com.
A rear step that leaves the receiver usable
This rear hitch step provides a stepping surface for access through the rear doors on Sprinters without a rear step bumper. It bolts onto the factory receiver hitch rather than occupying the hitch opening, so the receiver remains usable.
Van Compass describes it as a high-clearance design with no loss of ground clearance and says it adds protection from vehicles parking too close behind the van. The bolt-on assembly can be removed to return the vehicle to stock.
Steel step
The stepping surface is powder-coated steel.
Hitch-mounted brackets
Steel mounting brackets attach the step to the factory receiver hitch.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Van Compass
Mercedes Sprinter NCV3 2500 · 2007-2018 · 4X4 and 2WD.
Hitch tack-weld clearance
On some hitches, the tack weld prevents the backing plate from sitting flat despite its clearance hole. The guide calls for sanding the weld smooth and spray-painting the area to prevent corrosion if needed.
Trailer wiring repositioning
The guide requires cutting a zip tie and moving the 7-way trailer wiring clear of the hitch during installation, then repositioning it into the side zip tie and behind the bolts.
Hitch and bumper
Designed for the factory rear hitch and stock non-step rear bumper; Van Compass does not guarantee fitment with aftermarket hitches.
Installer guidance
Van Compass’s FAQ permits DIY installation, but its Warranty Policy requires professional installation according to the instructions for warranty coverage.
Specs, parts & installation
Step and brackets
| Step | 1/8" steel, powder coated |
|---|---|
| Mounting brackets | 1/8" steel |
What’s in the box
Step and mounting brackets
One rear hitch step, 1/8" powder-coated steel, and 1/8" steel mounting brackets; the matching guide shows two backing plates.
Mounting hardware
Eight 7/16-14 UNC x 1.0” long carriage bolts, clear zinc; eight 7/16-14 UNC nylock nuts; eight 7/16” GR8 flat washers, yellow zinc.
Installation at a glance
Van Compass’s matching guide estimates 15-30 min for a professional shop or driveway installation.
The step bolts to the factory rear hitch using backing plates and supplied hardware. The rear bumper may need to be pushed up slightly to wedge the plates into place.
Follow the matching guide below, including its tack-weld clearance and trailer-wiring steps.
Tools listed in the matching guide
- Cutters or a similar tool for cutting zip ties.
- Basic wrench and socket set, including 5/8” SAE.
- 4-1/2” angle grinder with metal sanding disc may be needed for tack-weld clearance; use spray paint on the sanded area to prevent corrosion.
Mounting sequence from the matching guide
- Cut the indicated zip tie behind the hitch and pull the 7-way trailer wiring out of the side zip tie to clear the hitch.
- Install the two backing plates; their longer side with the hole sits on top of the hitch tube. Address tack-weld clearance as described above; the bumper may need to be pushed up slightly.
- Slide the plates as far over as possible and insert the top carriage bolts from behind.
- Position the step and insert the bottom carriage bolts from below so its underside remains smooth.
- Place a washer under each nylock nut; align every bolt and start every nut before snugging the hardware.
- Use a 5/8” socket or wrench; the guide specifies 45 ft-lbs (61 N.m) for the nuts.
- Reposition the trailer wiring into the side zip tie and tuck it behind the bolts.
Source notes
- Van Compass’s product page lists Sprinter 2500, 1994-2018, 4X4 and 2WD; its matching installation guide is titled “2007-PRESENT, MERCEDES SPRINTER NCV3.” This listing follows the guide’s 2007 start year and NCV3 scope, retaining the product page’s 2018 end year and 2500/drive scope.
- The product page links the installation guide for a different kit, titled for the Sprinter NCV3 3500; this listing instead uses the maker’s matching rear hitch step guide.
- The product page recommends 0.5 Hours shop labor; the matching guide estimates 15-30 min for both professional shop and driveway installation. This listing follows the guide.
Lead Time
Orders ship first-come, first-shipped; international service is described separately on two pages; report loss, missing items or damage within 2 days of tracked delivery.
Read Van Compass lead time policy on WNDR BuiltWarranty
Specified hard parts: original-owner ownership term; Falcon shocks: 1 year; powder coating/excessive zinc corrosion: 60 days; professional installation required.
Read Van Compass warranty policy on WNDR BuiltReturns
Return-window start date varies by page; eligible unused returns incur 20% restocking and customer-paid shipping; electronics, including PedalBox, and CLOSEOUT items are final sale.
This product
Van Compass marks this product CLOSEOUT; its Shipping, Return and Cancellation Policies states that closeout items are non-returnable and all sales are final.
What are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon