
Van Compass
OUTBACK REAR DOOR STORAGE SYSTEM - SPRINTER 2019-UP
Indexed listing. WNDR Built doesn't sell this product; the button opens vancompass.com.
Rear-door storage without a surrounding carrier frame
The OutBack system mounts exterior storage boxes or a utility panel to the factory rear door using separate carrier brackets rather than a surrounding frame. The brackets attach at four points on the door, creating the mounting base for the selected storage arrangement.
A Big Box configuration provides a box directly on the door mounts. The panel-based configurations instead use the Grid Utility Panel, either on its own, with a Little Box, or with a Little Box and spare-tire mount. You select the door side and configuration together.
Big Box shelving and door
The Big Box guide lists large, small and Packout shelves, describes multiple shelf positions and gives a procedure for reversing the box’s front-door swing.
Utility panel reinforcement
The utility panel uses two support gussets to stiffen its upper half.
Door-mount bushings
The door-mount guides use shock bushings at the center-plate attachments and specify slight compression rather than fully collapsing them.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Van Compass
- Sprinter · 2019-PRESENT · High roof only (product page)
- Drive type: ALL
Choose the storage configuration
Every configuration is offered for DRIVER - LEFT or PASSENGER - RIGHT.
BIG BOX
- Door mounts for the selected side and a Big Box.
GRID PANEL ONLY
- Door mounts for the selected side and the Grid Utility Panel.
GRID PANEL AND LITTLE BOX
- Door mounts for the selected side, Grid Utility Panel and Little Box.
GRID PANEL AND LITTLE BOX WITH SPARE TIRE MOUNT
- Door mounts for the selected side, Grid Utility Panel, Little Box and vehicle-specific wheel mount.
Door drilling required
Installation requires drilling the rear door panels, deburring the holes and touching up exposed metal with paint.
180 degree hinges required
Requires 180 degree hinges, sold separately; not compatible with 270 degree hinges.
Total door load
Van Compass states: MAXIMUM TOTAL DOOR LOAD NOT TO EXCEED 200LBS, INCLUDING BOX AND CONTENTS.
Fastener recheck
The guides require re-inspecting all fasteners after the first 50–100 miles of use and re-torquing/tightening as necessary.
Accessory requirements
The door mounts must be secured with an OutBack Big Box or Utility Panel; they are not standalone carriers and may damage the vehicle without one of those components. The Little Box mounts on the Utility Panel. The spare-tire mount requires the Door Mount and Utility Panel to be installed first.
Spare-wheel mount
The wheel-mount guide lists Sprinter 2500 and 3500. Use the 130mm BC stud pattern for Sprinter 2500 and 205mm BC for Sprinter 3500.
Aftermarket Sprinter 3500 wheels
Some aftermarket aluminum wheels may require longer wheel studs if their flange is thicker than 1”.
Specs, parts & installation
Carrier construction
| Brackets | Precision-cut and formed 1/4" aluminum |
|---|---|
| Finish | Powder-coated |
| Door attachment | 4 mounting points on the factory door |
What’s in the box
Door mounts — all configurations
Side-specific door-mount hardware includes hinge and center plates, hinge attachment parts, panel plates, striker or internal door supports, shock bushings and fasteners, as listed in the matching guide. The passenger-side kit also lists an emblem badge, gasket, handle extension and pinch plate.
Big Box configuration
Big Box with large shelf, small shelf, Packout shelf and mounting hardware listed in its guide.
Grid Panel configurations
Grid Utility Panel with two support gussets and mounting hardware. Little Box and its mounting hardware are included when that configuration is selected.
Spare-tire configuration
The wheel mount, three wheel studs, three lug nuts and mounting hardware listed in its guide are included with the Grid Panel and Little Box with Spare Tire Mount configuration.
Installation at a glance
The product page recommends 1 hour (per door) for door mounts, 0.25 Hours for the Grid Utility Panel, 0.5 Hours for the Little Box, 0.5 Hours for the Big Box and 0.25 Hours for the spare-tire mount.
The door-mount guides estimate 1–1.5 hours for a professional shop and 1.5–2 hours for driveway installation. The Big Box guide calls for at least two people; two people are also recommended, but not required, for the Utility Panel and Little Box.
Install the selected Big Box or Utility Panel before final tightening of the door mounts. Fit one Utility Panel support gusset at the uppermost position and the second in the upper half. For a Little Box, move any interfering Utility Panel screws so the box sits flat against the panel.
After installation, open and close both rear doors through their full range to check for interference.
On the passenger side, installation requires removing the Mercedes emblem, fitting the included replacement badge and gasket, and installing the door-handle extension. On the driver side, if the striker support causes poor latching or requires slamming, the guide recommends adjusting the striker plate and testing again.
Accessory installation estimates from the manuals
- Big Box: professional shop 0.5 hours; driveway 0.5-1 hours.
- Utility Panel: professional shop 0.25 hours; driveway 0.25-0.5 hours.
- Little Box: professional shop 0.25 hours; driveway 0.25-0.5 hours.
- Wheel mount: professional shop 0.25 hours; driveway 0.2-0.5 hours.
Tools listed in the guides
- Door mounts: SAE hex keys, basic wrench/socket set, auto trim tool, drill with metal-cutting bits and a felt pen. The Sprinter door-mount guides list 7/16” drill bits, a 5mm hex key and Torx bits; the driver-side guide also lists T-45 for the striker adjustment.
- Box, Utility Panel and wheel-mount guides list a 7/32 Hex Key wrench and 9/16 wrench/sockets; the wheel-mount guide also lists a 22mm wrench/socket.
Wheel-mount depth adjustment
- The wheel plate depth must put the tire tight against the Utility Panel. The guide suggests setting the mount approximately 1/4” below a straight edge across the tire before securing it.
Lead Time
Van Compass allocates and ships orders first come, first shipped; freight orders requiring a separate payment are held until paid in full.
Read Van Compass lead time policy on WNDR BuiltWarranty
Exterior accessories have materials-and-workmanship coverage for the original purchaser’s duration of ownership, with powder coating covered for 60 days and warranty labor and shipping excluded; the Warranty Policy requires professional installation, while the FAQ says customers can install products themselves.
Read Van Compass warranty policy on WNDR BuiltReturns
The Refund policy gives 30 days from purchase, while Shipping, Return and Cancellation Policies require return authorization within 30 days of receipt; returns must be unused/uninstalled with original packaging, carry a 20% restocking fee (potentially higher for missing parts or damaged packaging), and return shipping is the customer’s responsibility; CLOSEOUT items are non-returnable.
Read Van Compass returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon