
Dark Star Offroad
Mercedes Sprinter BackPack
Indexed listing. WNDR Built doesn't sell this product; the button opens darkstaroffroad.com.
A rear-door platform for boxes and accessories
The BackPack adds exterior storage mounting space with a MOLLE panel set within a solid aluminum frame. Dark Star Offroad describes it as compatible with most aftermarket boxes and accessories, with mounting possible on either the panel or the frame depending on the accessory.
Its three-point attachment uses the factory hinges at two points and a separate door attachment at the third. The rack is supplied with its mounting brackets and hardware; storage boxes and other accessories are sold separately.
Panel or frame mounting
Accessories can mount to the MOLLE panel or the frame, depending on the accessory.
Cushioned door attachment
The installation guide places a square urethane bushing between the rack and the rear door.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Dark Star Offroad
Fits 2019+ Sprinter vans.
180-degree hinges required
Must have 180-degree rear door hinges; will not work with 270-degree hinges.
Drilling required
The third mounting point requires a hole through the outer and inner door skin: a ⅛” pilot hole enlarged with a ⅜” drill bit. Use a step bit on the interior side only if additional clearance is needed, and coat exposed metal edges with a rust-preventive coating.
Door position
Rear passenger door only; the maker says no driver-side version is available.
Accessory compatibility
Dark Star Offroad lists most aftermarket boxes and accessories, including Roambuild, OWL, FVC, OneUp, Avatar Offroad and Aluminess.
Specs, parts & installation
Frame & dimensions
| Frame | Solid aluminum |
|---|---|
| Exterior width | 23.5" |
| Exterior height | 49" |
| Weight limit | Dark Star Offroad states 150 lbs. |
What’s in the box
Carrier & plates
One BackPack carrier, one lower mounting plate, one upper mounting plate and one inner-door square washer.
Van mounting hardware
Four 3/8-16 x 1-1/4" button socket head screws, five 3/8"-16 nylon-insert locknuts, six 3/8" flat washers, one 3/8-16 x 2-1/2" socket cap screw and one square urethane bushing.
Box/accessory hardware
Four 3/8-16 x 2-1/2" hex cap screws, four 3/8" neoprene EPDM washers, four 3/8"-16 nylon-insert locknuts and four 3/8" flat washers.
Installation at a glance
The installation guide estimates 4 hours and calls for a helper to hold the rack in position.
Park on a level surface and remove factory plastic door trim if present.
The rack attaches at the factory hinges and a third door mounting point.
Installation sequence from the maker guide
- Confirm the upper and lower mounting-plate orientation using the guide images.
- Hold the bracket edges against the factory or aftermarket door stops and snug the four hinge bolts without fully tightening them.
- Align the door bracket, mark its hole and remove the rack before drilling.
- Make a hole through the square urethane bushing, insert the provided 2-½” bolt, and fit the square washer and nylon-insert nut from inside the door.
- Secure all fasteners and fully tighten the four hinge bolts with the rack in the desired position.
Tools listed by Dark Star Offroad
- Power drill; ⅛” metal pilot drill bit; ⅜” metal drill bit; step drill bit
- 5/16” and 7/32” Allen keys
- 9/16” socket with extender; 9/16” wrench
- Rust Bullet or another rust-preventive coating
Lead Time
Read Dark Star Offroad lead time policy on WNDR BuiltWarranty
Read Dark Star Offroad warranty policy on WNDR BuiltReturns
New, unused parts may be refunded after return and inspection; return shipping is not covered.
Read Dark Star Offroad returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon