
Flatline Van Co.
Sprinter Van Rear Bumper
Indexed listing. WNDR Built doesn't sell this product; the button opens flatlinevanco.com.
An aluminum rear bumper with mounts for factory sensors
The Flatline Van Co. Sprinter Van Rear Bumper replaces the factory rear bumper cover with an aluminum bumper mounted to the frame through steel brackets. Its shape follows the van’s contours; Flatline says it clears the rear doors and maintains the factory departure angle without affecting ground clearance.
The design transfers the factory parking sensors and wiring harness into snap-in bezels, with separate brackets for the rear radar sensors. Two cutouts provide mounting locations for optional rear/reverse lights, while wire-management holes and slots provide places to secure their wiring. The bumper is designed to match Flatline’s Sprinter Front Bumper and Sprinter Rear Plate Step.
Sensor transfer
Snap-in parking sensor bezels receive the factory sensors; the guide directs reinstalling them in their original orientation.
Optional rear lighting
Two cutouts fit Baja Designs S2 SAE or S2 Sport LED Pod Lights, with holes and slots for wire management.
Frame attachment
Driver- and passenger-side bumper brackets connect the bumper to frame bracket weldments.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Flatline Van Co.
- 2019+ Sprinter 1500/2500/3500/3500XD · 144"/170"/170" EXT · Low/High Roof.
Dually and rear-step exclusions
Not compatible with dually vans, Flatline’s Sprinter Rear Step or Sprinter Rear Tube Step.
Factory-part modifications
The installation guide states that modifications to factory parts are required and are performed at your own risk.
Electrical work
Disconnect the battery, both if applicable, before electrical work, and work on a flat surface.
Optional lights
Light pods are an optional purchase, not part of the base bumper configuration.
California Proposition 65 warning
WARNING: This product can expose you to chemicals including lead and lead compounds, DEHP and bisphenol A (BPA) which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Rear radar sensor configuration
The installation guide with the 2025+ radar-kit procedure uses the existing sensor bracket assembly for 2019–2024 rear adaptive radar sensors. For vans newer than 2024, it directs using the 2025+ Rear Blind Spot Sensor Kit and retaining the radar sensor cover plate.
Hitch fit
Works with or without the Mercedes-Benz factory hitch, and with aftermarket hitches similar in shape to the factory hitch.
Installer requirement
Flatline recommends professional installation. If you have no mechanical experience and are not thoroughly familiar with the procedures, its guide requires a professional installer or other qualified person.
Before use
Check mounting points and attachments before use, and regularly inspect the product for wear or damage.
Specs, parts & installation
Construction
| Bumper skin | 3mm aluminum |
|---|---|
| Brackets | 5mm stainless steel |
| Finish | Black textured UV-rated exterior-grade powder coat |
| Hardware | Black oxide stainless steel hardware; Grade 8 zinc yellow chromate mounting hardware |
| Weight | Flatline states the total weight is just under 45 pounds. |
What’s in the box
Bumper and frame mounts
One rear bumper assembly; one driver-side and one passenger-side bumper bracket; one driver-side and one passenger-side frame bracket weldment.
Parking sensor bezels
Six Sprinter park sensor bezels.
2025+ radar sensor kit
The guide with the 2025+ procedure lists two rear sensor brackets, two rear sensor straps and eight rear sensor spacers.
Mounting hardware
Hex head screws, button head screws, flat washers and nylon locknuts, as listed in the installation guide.
Installation at a glance
The installation guide lists 2-3 hours; Flatline’s product page recommends two people to lift the bumper into place.
Remove the factory bumper cover and transfer the sensor harness and sensors. Fit the bumper brackets and frame brackets, position the assembled bumper, bolt it to the frame brackets and reconnect the harness.
If adding optional off-road lights, the guide advises having them ready before installing the bumper and fitting them to the light brackets before mounting the bumper.
Sensor and mounting sequence
- Remove the rear side trim, upper rear bumper trim, lower plastic rivets and clips, and the Torx bolts securing the factory bumper cover.
- Disconnect the sensor harness under the van and remove the cover, noting each park sensor’s orientation.
- Fit the bumper brackets and park sensor bezels, then reinstall the upper trim with the retained plastic rivets.
- Transfer the harness as an assembly and fit the radar sensor brackets for the applicable sensor type; for 2025+ vans, use the radar-kit assembly procedure on both sides.
- Refit the park sensors in their original orientation and secure the harness at the guide’s zip-tie locations.
- Install frame brackets by replacing factory bolts one at a time, then position and attach the bumper and reconnect the harness.
Tools listed by Flatline
- Flathead screwdriver; auto panel removal tools; ratchet and extension.
- 18mm wrench and socket; 19mm wrench or socket; 3/4” wrench and socket; 9/16” wrench and socket; 7/16” wrench.
- T40 Torx; 7/32” and 5/32” Allen wrenches; C-clamps. Tools are not included.
Source notes
- Flatline’s product-page Fitment Notes exclude 2025+ vans with JA7 blind spot or JT7 sideguard assist options; its linked 25-page installation guide provides a 2025+ rear blind spot sensor kit and installation procedure on pages 4 and 13–16. This listing follows that guide’s 2025+ sensor procedure, which does not name JA7 or JT7.
- Flatline’s other linked, 21-page installation guide has no 2025+ radar-kit section; the 25-page guide lists the kit and its installation. This listing uses the guide with the 2025+ procedure for those components.
- The 25-page guide’s hardware table lists eight 1/4-20 x 1 button head screws, four 1/4-20 nylon locknuts and four 1/4 flat washers; step 3.8 calls for two plus four of each per side and says to repeat on both sides. These disputed hardware quantities are omitted here.
- The 25-page guide’s hardware table lists 3/8-16 x 1 button head screws, while step 3.1 specifies 3/8-16 x0.75 screws for the bumper brackets. The disputed screw length is omitted here.
Lead Time
In-stock dispatch: 1–2 business days; LTL delivery: typically 7–21 business days; preferred service uses flat rates; economy may be free with longer lead times.
This product
The bumper product page says it ships freight on a pallet to your home, arriving 1-2 weeks after ordering. It advertises free lower-48 shipping; the FAQ also says free shipping, while the shipping policy lists flat-rate and economy options.
Warranty
Flatline-made products have a one-year limited warranty for the original purchaser; purchaser-paid claim returns and exclusions apply; other manufacturers’ products carry only their applicable manufacturer warranties.
Read Flatline Van Co. warranty policy on WNDR BuiltReturns
Returns within 30 days of receipt require RMA, unused original-packaged items and 20% restocking; customer-paid shipping unless Flatline error; clearance/garage-sale/final-sale excluded; identified custom/made-to-order exclusions may apply.
Read Flatline Van Co. returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon