
Aluminess
Recon Side Steps - 2014-26 RAM Promaster
Indexed listing. WNDR Built doesn't sell this product; the button opens aluminess.com.
Side-door entry steps with tread, drainage and light mounts
These welded-aluminum side steps provide an entry surface for passengers and pets, with a longer passenger-side step and a shorter driver-side step. Their tread pattern and drain holes give water a path off the stepping surface.
Multiple attachment points connect the steps to the van’s pinch weld and unibody supports. Integrated L-Track Bowtie mounts provide attachment points for gear or a leash at camp, while tabs along the steps provide locations for rock lights.
Rock-light locations
Four preset mounting locations accept Baja Designs rock lights: three on the passenger side and one on the driver’s side.
Stepping surface
The steps provide a 6" stepping surface.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Aluminess
2014-26 RAM ProMaster (maker title); ProMaster 1500, 2500 and 3500 are listed under Detailed Specs.
Drilling required
Installation requires drilling through the van’s pinch weld with a ¼” drill; the manual allows opening tight holes to 5/16”. Self-tapping screws also fasten into the body and unibody supports.
Two-person installation
Aluminess’s installation manual requires two people.
Use and legal compliance
Aluminess states its products are designed for off-road vehicle use and may exceed factory-designed vehicle capabilities. Purchasers must determine suitability and review applicable vehicle laws before use.
Mounting surfaces
Before fastening, verify that the pinch-weld mounting surfaces have no obstructions and that the step brackets align with the underside unibody supports.
Aftermarket vehicle conversions
Aluminess designs its products for factory-manufactured vehicles; some aftermarket conversions are incompatible.
Specs, parts & installation
Steps
| Material | Welded aluminum sheet metal |
|---|---|
| Stepping surface | 6" |
| Driver-side length | 30 3/4” |
| Passenger-side length | 92" |
| Weight capacity | Aluminess states: 300 lbs |
Shipping dimensions
| Height | 16 IN. |
|---|---|
| Width | 104 IN. |
| Depth | 8.5 IN. |
| Weight | 28 LBS. |
What’s in the box
Steps and supports
One driver-side Recon Side Step and one passenger-side Recon Side Step; one front support bracket for each side and two threaded inserts.
Hardware and lubricant
Ten ¼”-20 x 1" stainless button-head bolts; fourteen ¼”-20 stainless nylon-locking nuts; twenty-four ¼” x 5/8 stainless washers (.03" thick); thirty-eight #14 x 1 1/2” stainless self-tapping bolts; one 2g anti-seize packet.
Installation at a glance
Two-person installation with drilling through the pinch weld and self-tapping attachment to the body and unibody supports.
Align each step to the unibody supports, B-pillar seam and front fender flare; keep it level while fastening. Aluminess highly advises 5/32” or 3/16” pilot holes in the reinforced unibody mounting areas.
Fit the front support brackets and threaded inserts, and check all fasteners. Aluminess recommends anti-seize on stainless bolt threads.
If installing Baja Designs rock lights, use the hardware supplied by Baja Designs. If it does not fit the mounting-tab hole, the manual calls for drilling that hole with an 11/64” bit.
Verify mounting hardware remains tight after 100 miles and periodically thereafter.
Tools listed by Aluminess
- Drill with 3/16”, 1/4” and 5/16” bits
- Standard wrench set
- Center punch or scribing tool
- Level
Lead Time
This product
Aluminess’s product page states limited stock and possible lead times; contact info@aluminess.com for current timing.
Warranty
Read Aluminess warranty policy on WNDR BuiltReturns
Read Aluminess returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon