
Unaka Gear Co.
Ram ProMaster Roof Rack - Premium - 159" High Roof
Indexed listing. WNDR Built doesn't sell this product; the button opens unakagearco.com.
Movable crossbars within an aluminum shell
The Premium rack combines an adjustable 8020 frame with an aluminum shell for a roof layout built around solar panels and accessories. The crossbars can be positioned along the side rails to suit the layout.
Laser-cut side plates cover the 8020 side rails and join to a reinforced, single-piece welded aluminum wind fairing. That side-plate and fairing assembly distinguishes it from the Standard rack’s acrylic fairing and 8020 foundation. The Premium frame uses black powder-coated bars, with internal splice plates joining the rail sections.
Channel access
Drop slots in the 8020 bars allow T-nuts for solar panels and other accessories to be added later.
Prepared hardware
The product page lists pre-measured double T-nuts and Loctite pre-applied to the necessary bolts.
Light bar capability
Unaka describes integrated light bar capability on this Premium product page.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Unaka Gear Co.
- 2014+ Ram ProMaster · 159" · High roof
2025–2026 antenna condition
On 2025 and 2026 Ram ProMaster vans, press the wind fairing’s bulb seal over the antenna during installation so the fairing sits behind the factory marker lights, as required by the product page.
Installation access
The manual requires two people and two sufficiently tall ladders on level ground. Unaka strongly recommends a qualified professional or installation according to its detailed instructions.
Solar bracket requirements
For flush-mount installation, the manual lists minimums of 4 brackets for a 150W solar panel or smaller, 8 for a 150W to 250W panel, and 16 for 300W and larger; follow the solar panel manufacturer’s requirements if it specifies more brackets. Solar panels are sold separately.
Use terms
Unaka’s Terms & Conditions of Sale states that its parts are intended for off-highway application only; installation may void vehicle warranty coverage.
Roof attachment
Requires the van’s OEM roof T-studs. The brackets slide over the T-posts from the outside in and attach through 8020 adapter brackets.
Solar panel width
Unaka’s product page lists a maximum panel width of 59.25".
Crossbar positioning
Crossbars may need to move to avoid interference because the 8020 adapter brackets and inside splice assemblies are not relocatable.
Hardware checks
The rack manual requires an initial torque check after 4 to 7 days, a follow-up after 1 month, routine checks every 3 to 4 months, and checks after moderate driving on bumpy or gravel roads.
Specs, parts & installation
Frame & fairing
| Foundation | 15 series 8020 aluminum |
|---|---|
| 8020 finish | Black powder coat |
| Wind fairing | Aluminum |
| Crossbars | 4 ultralight 15 series 8020 crossbars |
| Crossbar length | 60.25” — model-specific manual |
| Side plates | Laser-cut aluminum |
What’s in the box
Rack shell & rails
Roof rack, aluminum wind fairing, laser-cut side plates, 8020 side rails, inside splice plates and end caps.
Crossbars & roof mounts
4 ultralight 15 series 8020 crossbars, crossbar connectors, roof mounting brackets, 8020 adapters and installation hardware.
Solar mounting
16 flush-mount solar panel brackets and mounting hardware for two 200W solar panels; solar panels are sold separately.
Tools listed in the current manual
One 3/16 T-handle Allen wrench, one 1/8 Allen wrench, one 5/32 Allen wrench and two 7/16 simple open spanners.
Installation at a glance
The model-specific manual requires two people and two ladders.
Unaka’s FAQ estimates 4+ hours solo for a Premium rack, but the manual’s two-person requirement still applies.
Pre-assemble the hardware, fit the brackets over the factory roof T-posts, and leave the mounting hardware loose until the rails and crossbars are centered, parallel and square. Check and tighten the adapter hardware before solar panels or accessories restrict access.
Use Blue Loctite 242 on bolts not paired with nylock nuts and anti-seize where the manual calls for it; anti-seize is not included.
Take extra care not to drop the wind fairing onto the windshield or front of the van while positioning it.
Use the REV 1 manual dated 3/27/2025; its item numbers and included-tool list differ from the earlier PDF dated 3/26/2025.
Assembly sequence in the model-specific manual
- Lay out the parts and keep sub-kit hardware separate; similar-looking pieces are not interchangeable. Pre-install the selected T-nuts and connectors loosely.
- Prepare the crossbars and mount brackets loosely over the roof T-posts. Slide on the rail sections and join them with inside splice plates, keeping the roof attachment loose for alignment.
- Use at least three crossbars, near the front, middle and rear, to set spacing; add accessory T-nuts before they become difficult to access.
- Center the rack, set both sides to matching positions and make it parallel and square. Tighten the adapter and roof attachment hardware before continuing.
- Install the side plates and wind fairing.
- Reposition crossbars for the final layout, fit end caps without overtightening their self-tapping screws, and check all hardware after assembly.
Tools and supplies listed in the manual
- Two ladders, tape measure and a torque wrench covering the manual’s specified fastener torques.
- SAE sockets including ½” and 7/16”; ½” box wrench; the manual lists 3/16”, 1/8” and 5/32” Allen tools and two 7/16 open spanners as included.
- Blue Loctite 242 and anti-seize. Reapply threadlocker if a bolt with Loctite has been fully loosened or loosened repeatedly.
Optional solar panel preparation
- Solar panels are sold separately. Follow the panel maker’s bracket requirements if greater than Unaka’s stated minimums.
- If adding mounting holes, protect the panel with a ½” or ¾” backer board inside it; use a center punch, an 1/8” pilot bit and a 5/16” finishing bit, then remove drill shavings.
- The manual distinguishes the nearly identical 9/16” and 5/8” bracket bolts; use the specified longer bolt when two panel brackets share one T-nut.
Lead Time
Shipping Information excludes oversized items from free shipping; Shipping policy excludes LTL freight; for destinations without checkout methods, Shipping Information offers email help while Shipping policy says Unaka does not ship there.
This product
Unaka’s product page advertises free shipping on roof racks to the Lower 48.
Warranty
Unaka-designed and fabricated parts have workmanship/material defect coverage for the original purchaser for the product’s production lifetime; third-party components, wear parts and modification/misuse are excluded, and coatings have 180-day coverage.
Read Unaka Gear Co. warranty policy on WNDR BuiltReturns
Refund policy’s Returns section: new/original-packaging returns within 30 days of invoice, minimum 10% fee if you cover return shipping or 20% if forgoing it, with freight prepaid; its Terms & Conditions of Sale section instead says 15 days after receipt, 15% and no opened/installed returns. Unaka’s Returns section excludes custom-order merchandise, electronic merchandise, discontinued items and specially priced items.
Read Unaka Gear Co. returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon