
REAR DOOR ACCESS LADDER FOR RAM PROMASTER HIGH ROOF [H2]
Indexed listing. WNDR Built doesn't sell this product; the button opens primedesign.net.
A ladder mounted to the rear door
Prime Design’s rear door access ladder provides a climbing route at the back of the van. Upper and lower door brackets hold the aluminum ladder to the door, with rubber isolators seated against the door edges. The lower hanger rods draw the brackets into place, and the ladder is aligned vertically during installation.
This listing is for the clear-anodized ladder shown on the maker’s product page. The matching assembly manual covers installation, climbing precautions and ongoing inspection of the door attachment.
Anodized aluminum
Prime Design describes the anodized finish as protection against corrosion, scratching and fading; its manual requires cleaning to maintain that finish.
Adjustment hardware
The manual instructs installers to remove and retain the hanger-rod hardware after installation for future adjustments.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Prime Design
- 2014+ Ram ProMaster · High Roof [H2], as specified by the matching assembly manual.
Backup camera clearance
Relocation of the OEM backup camera may be required if the ladder is in its field of view.
Door must be latched
Before using the ladder, securely close and latch the door at both top and bottom. Do not drive with the rear door open or anyone using the ladder.
Climbing precautions
Face the ladder and maintain three-point contact: two feet and one hand, or one foot and two hands. Keep both hands and arms free; secure hand tools in a pouch, holster or tool belt rather than carrying them in hand. Never jump from or slide down more than one rung or step at a time.
Grip and weather
Avoid climbing with slippery or greasy hands or gloves. Keep the ladder and footwear free of oil, grease and other slippery substances. Avoid use during high winds or storms, and clear ice, frost or snow before use.
User limitations
The manual prohibits use by people who are prone to fatigue or have physical limitations, impairing medication effects or other conditions that prevent safe climbing.
Inspect before continued use
Mountings, fasteners and hardware must be intact and secure. Remove the ladder from service if any are missing, loose or damaged until corrected. Structural damage or defects require removal from service and repair by a competent individual, or removal and/or destruction to prevent use.
Mounting position
The manual specifies one mounting position on the vehicle and warns that a different position may compromise attachment.
OEM parts
Use only OEM-supplied parts. Do not add rubber, plastic or other material between the door brackets and vehicle body unless supplied with the ladder.
Specs, parts & installation
Construction
| Material | Aluminum |
|---|---|
| Finish | Clear anodized |
What’s in the box
Ladder and brackets
One access ladder; upper mounting bracket assembly (LH/RH pair); lower mounting bracket assembly (LH/RH pair); ladder-bottom hanger brackets (LH/RH pair).
Mounting hardware
One access-ladder hanger-bracket hardware kit: eight M8 x 20MM bolts, eight 5/16” flat washers and eight lock washers, as listed in the assembly manual.
Installation at a glance
Use hand tools only to tighten fasteners; the manual prohibits power-tool tightening.
Assemble the mounting brackets and lower hanger rods, hang the upper door brackets over the door edge with the rubber isolators fully seated, and align the ladder vertically. Prime Design recommends positioning the vehicle on ground as level as possible.
Do not overtighten the hanger-rod nuts: the manual warns this can damage the door skin. Tighten the lower hanger-rod nut until the bracket’s rubber isolator begins to compress. The manual specifies 90 in-lb for the bracket assembly bolts and 90 in-lbs for the lower hanger-rod clamp bolts.
Check and retorque mounting fasteners after the first week of initial service, then monthly thereafter. Inspect for corrosion and deterioration every six (6) months, or more frequently as conditions require, and check that the ladder retains its specified position.
Tools listed by Prime Design
- Combination wrench, 13MM; ratchet with 13MM socket; torque wrench with 13MM socket.
- Torpedo level, tape measure and grease or wax pencil.
Assembly details
- The upper bracket bolts use hanger-connector holes #3 and #7; the lower bracket bolts use holes #3 and #5. Left and right mounts have carriage-bolt heads facing inward.
- Remove the factory-preassembled lower hanger-rod tightening hardware for installation into the clamps, then reinstall it. Do not tighten the rods before the manual’s alignment and tightening steps.
Care and inspection
- Inspect rungs, side rails, mounting brackets, mounting fasteners, rubber isolators and rivets. Maintain records of scheduled inspections, maintenance and repairs.
- Repairs must use direct OEM replacements. Retain all OEM safety labels and replace missing labels only with OEM-approved ones.
- Clean with mild soap and water; automotive aluminum cleaners and polishes may be used for stubborn contamination. Do not use harsh chemicals, aggressive alkaline or acid cleaners, or excessive abrasive rubbing.
- Do not use strong cleaners on surrounding glass or other components where they can contact the aluminum; wash the ladder immediately if contact occurs.
Source notes
- Prime Design’s assembly manual, page 6, step 4.1 says to measure horizontally outward approximately 5.00” from the inner door seam; step 4.2 says to mark the top and bottom at 4.50”. The manual does not resolve these two offsets; no numerical mounting offset is specified in this listing.
- Prime Design’s product page lists 18 kg; its product overview, page 1, lists an empty weight of 18.25 lbs. These different weight figures are not reconciled in the supplied sources.
Lead Time
Built-to-order racks typically take about two weeks to manufacture, partially assemble, and ship; actual lead time varies.
Read Prime Design lead time policy on WNDR BuiltWarranty
Read Prime Design warranty policy on WNDR BuiltReturns
Read Prime Design returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon