
The BugWall
RAM Promaster Rear Screen
Indexed listing. WNDR Built doesn't sell this product; the button opens thebugwall.com.
A removable insect screen for the rear doors
The BugWall rear door insect screen is intended to screen a RAM Promaster's rear doorway when insects are present.
Zippers on both sides for roll-up; rolled flaps are secured with included buckle straps. Zipper across the top lets you remove the rolled-up screen for seasons when insect protection is not necessary (listed as new for Bug Wall V2).
Weighted lower edge
Foam layer across the bottom adds weight for a better roll-up (listed as new for Bug Wall V2).
Center closure
Closure choice: magnetic closure for walking in and out, or a zipper closure; the maker says the zipper option gives a more secure seal.
Screen materials
No-See-Um bug netting on marine canvas.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by The BugWall
RAM Promaster · High, Low and Super High roof heights · Rear doors
Choose your roof height
Choose the option matching the van's roof height.
High ( Most Class B RVs)
- High ( Most Class B RVs) roof
Low
- Low roof
SUPER High (Extra High-New model for 2024)
- SUPER High (Extra High-New model for 2024) roof
Choose your center opening
Both closure options are offered for every listed roof height.
Magnet
- Magnetic closure for walking in and out.
Zipper
- Zipper closure in the center.
Magnetic-screen tension
Too much side-to-side tension prevents the magnet strip from operating correctly; do not install a magnetic-closing screen too tight.
Weather-seal clearance
Leave enough fabric behind the flange and upper corners for the weather seal to seat fully. Pinch the weather seal shut before reinstalling it.
Roof options
High ( Most Class B RVs), Low, or SUPER High (Extra High-New model for 2024).
Separate side screen
A side sliding door screen is sold separately.
Specs, parts & installation
Materials & manufacture
| Materials | US made marine canvas with No-See-Um bug netting and USA made marine grade zippers. The BugWall states the screen is UV stable. |
|---|---|
| Manufacture | The BugWall states it manufactures its screens in Conway, SC. |
What’s in the box
Screen & roll-up straps
Insect screen with built-in buckle straps for securing rolled-up flaps.
Installation supplies
Roll of double-sided tape and clips supplied with the screen, as described in the brand-wide installation guide.
Package extra
Bugwall coozie (the installation guide says one was included in the package).
Installation at a glance
Installs around the rear door-opening flange with double-sided tape and clips beneath the weather seal.
Rear screens do not have a guideline: align the latch holes, slots or cuts with the rear-door latches to set the height.
Follow the updated written guide; the older videos are visual guides, and any supplemental instructions supplied with the screen also apply.
Installation sequence from the brand-wide guide
- Mark the weather seal and van so the seal can return to the same left-to-right position; remove the seal across the top and clean the flange with alcohol or water.
- Apply the double-sided tape across the top and around both corners, starting and ending just below the corners, ideally with half on each side of the flange; remove the red cover.
- Press the screen fabric onto the tape on the front and back of the flange, leaving room behind it for the seal.
- Use the thick supplied clips across the top. Start with one in the center and one toward each side, check the length before adding more because clips are difficult to remove, then place a clip about every 6-8" across the top.
- Wrap the fabric around the corners and down the sides, using clips suited to the metal thickness. Relief cuts in the screen material may help it follow the left-side bump-out; keep the zippers straight.
- After confirming placement, trim excess fabric. The guide recommends scissors; a razor is an alternative but is more likely to scratch the van.
- Pinch the weather seal shut, reinstall it using the reference mark, and use a mallet to seat it fully, especially in the corners.
Tools and supplies named in the guide
- Marker; alcohol or water for cleaning; a small hammer or mallet for the clips and seal; scissors (recommended) or a razor for trimming.
Lead Time
Lead times vary; contact the maker. Product banner: about 1 week to shipment for new orders; international taxes, fees, duties and tariffs are the buyer’s responsibility.
This product
The maker's product-page banner estimates 1 week until shipment from the shop for new orders due to high demand.
Warranty
Read The BugWall warranty policy on WNDR BuiltReturns
Returns within 30 days; later returns incur a 25% fee and are not accepted after 90 days.
Read The BugWall returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon