
Flatline Van Co.
Sprinter Van Side Ladder | Low Roof
Indexed listing. WNDR Built doesn't sell this product; the button opens flatlinevanco.com.
Roof access along the van’s contours
This side ladder provides roof access for cleaning solar panels, installing gear or reaching a rooftop deck. Flatline Van Co. says the double-kink bend keeps the ladder close to the van and follows its body contours.
The flat steps have formed dimples for traction. Two ladder halves join with bayonet couplers, with supplied rail nuts connecting the top to the roof rail and a mounting plate attaching the bottom at the pinch seam. The kit includes the mounting hardware; the guide also describes a chassis-beam support bracket for applicable installations.
Step width
Flatline lists 12.75” wide steps.
Rack connection
Flatline says the ladder is directly compatible with its Low Pro Roof Rack.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Flatline Van Co.
- 2007+ Sprinter 1500/2500/3500/3500XD | 144"/170"/170" EXT | Low Roof
Low Roof only
Flatline says this ladder is designed for Low Roof only.
Drilling required
The guide requires pilot holes in the pinch seam. It also specifies a 1/2 in hole through the chassis beam for the support bracket where applicable. The guide says the ladder must be removed to reach the remaining pinch-seam holes unless you have a 90-degree drill head.
Factory roof rail
The top of the ladder mounts to the existing factory roof rail on the supplied Sprinter rail nuts; the bottom attaches at the van’s pinch seam. The guide does not require a roof rack, and a rack is not included.
Low Pro Roof Rack
Flatline says the ladder is directly compatible with its Low Pro Roof Rack.
Accessories at the install location
The guide says you may need to loosen or temporarily remove mounted accessories to reach the roof rail and pinch seam. Its named examples are roof racks, side steps and water tanks, and it notes that sliding the rail nuts into place can be a somewhat lengthy process if a roof rack is already installed.
Guide figures
The guide’s illustrations show a 144" High Roof Sprinter; it says the same principles apply to the 170" and 144" Low Roof.
Installer requirement
Flatline’s guide says anyone with no mechanical experience who is not thoroughly familiar with the installation procedures must have the product installed by a professional installer or other qualified person, and that you are responsible for checking the mounting points and attachments before use and inspecting the product regularly.
Support-bracket placement
The guide recommends positioning the ladder close to the rear wheel well to use the support bracket, keeping the ladder straight up and down; the support-bracket steps apply only where applicable.
Specs, parts & installation
Ladder details
| Weight | 16.6 lb per Flatline |
|---|---|
| Step width | 12.75 in per Flatline; flat steps with formed dimples |
| Mounting | Factory roof rail at the top; van pinch seam at the bottom; chassis-beam support bracket where applicable per guide |
Maker warning
| Maker warning | Flatline’s product warning: This product can expose you to chemicals including lead and lead compounds, DEHP and bisphenol A (BPA), which are known to the State of California to cause cancer and birth defects or other reproductive harm. More information: www.P65Warnings.ca.gov. |
|---|
What’s in the box
Ladder sections
Ladder upper half and lower half
Mounting brackets
Mount plate and support bracket
Couplers
Two bayonet couplers
Roof-rail attachment
Two Sprinter rail nuts
Mounting hardware
Mounting hardware per the guide: 3/8-16 button head screws, lock washers, flat washers, nylon insert locknuts, 1/4 in self-drilling sealing-washer screws, 1/4-20 flanged button head screws and a 5 ml threadlocker bottle
Installation at a glance
The guide lists 1 hour and suggests additional help for a few steps.
Assemble the ladder, connect the top to the factory roof rail, then attach the lower mounting plate at the pinch seam and the support bracket where applicable.
Installation sequence from Flatline’s guide
- Join the upper and lower ladder halves on the two bayonet couplers using 1/4-20 flanged button head screws and threadlocker. Slide the Sprinter rail nuts along the roof rail to the position directly above the rear wheel well, then loosely secure the ladder to the rail nuts with 3/8-16 button head screws and lock washers. Position the ladder, then loosely attach the mount plate and the support bracket (if applicable) to the ladder bottom with 3/8-16 x 1 in screws, flat washers and locknuts. If the support bracket applies, mark where it lands on the chassis beam, swing it out of the way and drill through with a 1/2 in drill bit; the guide says to leave the bracket loose while fitting everything and to fasten it after drilling. Slide the mount plate up tight to the pinch seam and temporarily tighten the two bolts holding it to the ladder. Using the plate as a guide, drill pilot holes for the two center holes along the pinch seam with a 1/8 in bit and drive 1/4 in self-drilling screws through them; the guide says the ladder must be removed to reach the remaining two holes unless you have a 90-degree drill head, and that you can replace the self-drilling screws with 1/4-20 bolts and nuts. Tighten all fasteners along the roof rail and mounting brackets.
Tools and supplies
- 9/16 in and 7/16 in wrench or socket, 7/32 in and 5/32 in Allen wrenches, a power drill and 1/2 in and 1/8 in drill bits; tools are not included.
Lead Time
Flatline Van Co.’s FAQ says in-stock items ship within 1-2 business days and shipping is free to the lower 48; its Shipping policy lists flat-rate and economy options, with economy potentially free for longer lead times and typical LTL delivery of 7-21 business days.
Read Flatline Van Co. lead time policy on WNDR BuiltWarranty
One-year limited warranty from the original purchase date for the original purchaser, covering product cost only. It excludes installation, labor and freight, and damage from racing, competition or trail use, and is void for alteration, modification or improper installation.
Read Flatline Van Co. warranty policy on WNDR BuiltReturns
Returns require a pre-authorized RMA within thirty (30) days of receipt, unused items in resalable condition and original packaging; a 20% restocking fee applies and the customer pays return shipping unless Flatline made an error. LTL returns require coordination; clearance, garage-sale and final-sale items cannot be returned, and identified custom or made-to-order items may also be non-returnable.
Read Flatline Van Co. returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon