
Roambuilt
Mercedes Sprinter (2019- 2025) Low-Pro Front Bumper
Indexed listing. WNDR Built doesn't sell this product; the button opens roambuilt.com.
A low-profile bumper with winch and receiver mounts
The LoPro front bumper combines an aluminum outer shell with a steel winch plate and steel shackle mounts. This two-piece layout puts steel at the recovery mounting points while using aluminum for the exterior shell. The shell is designed to follow the Sprinter’s factory body lines.
A welded aluminum tube bull bar sits above the shell. Large hand cutouts provide access to the winch and a view of its line, while a front receiver adds another attachment point.
Factory sensor housings
Machined housings accept the factory parking sensors.
Skid-plate pairing
The bumper is compatible with Roambuilt’s skid plate.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Roambuilt
- Mercedes Sprinter (2019- 2025).
- Roambuilt also names Revel, Storyteller, EKKO and GH1 builds.
Choose the model year
Roambuilt’s product page asks for the Sprinter model year.
2019-2024
- Select for 2019–2024 model years.
2025+
- Select for 2025+ model years; this choice adds the ABA sensor housing.
Choose the drivetrain
Roambuilt’s product page separates these drivetrain configurations.
4WD/AWD 2500
- Select for a 4WD or AWD 2500.
2WD 2500 or Any 3500 Dually
- Select the bracket-assembly configuration for a 2WD 2500 or any 3500 dually.
Choose the parking-sensor configuration
Match the maker’s Sensors selection to your van’s equipment.
None
- Select if your van has no parking sensors.
Yes
- Select if your van has parking sensors.
Choose the adaptive cruise and brake-assist configuration
Roambuilt’s product page asks about Adaptive Cruise Control / Automatic Brake Assist.
N/A
- Select when this equipment does not apply to your van.
Yes, my van has this
- Select if your van has this equipment.
Required brackets and frame drilling
2WD and Sprinter 3500 dually installations require Roambuilt frame brackets. The 3500 requires DEF tank removal to drill holes in the frame. Roambuilt directs buyers to Sales at 480.674.0001 for details.
Retain the blue piece
For 2025+ model year vans, Roambuilt requires keeping the blue piece for installation; the last product image identifies it.
Factory bumper cutting
The product page describes cutting and preparation of the factory bumper and says it can remain on the van for that work.
If removing factory fog lamps
For 2019+ Sprinters with the factory fog lamps eliminated during bumper replacement, Roambuilt’s FAQ describes cutting the factory fog-lamp wiring and connecting a 50w 5ohm resistor to address the warning. Turn the vehicle off and disconnect the battery first; the resistor gets hot and must be kept away from other wiring.
Winch and shackle compatibility
Roambuilt lists Warn VR-EVO12S and Warn 12k Zeon series winches, up to 12k, and 3/4" shackles.
Vehicle systems
Roambuilt states compatibility with parking sensors, Cruise Control and Active Brake systems.
Specs, parts & installation
Construction
| Design | Two piece: steel winch plate and 5052 aluminum outer shell; steel shackle mounts |
|---|---|
| Bull bar | Welded aluminum tube |
| Finish | Black textured powder coat |
| Weight | 65lbs |
| Origin | Made in the USA |
Mounts and profile
| Shackle mounts | 1" thick, for 3/4" shackles |
|---|---|
| Front receiver | 2" |
| Added profile | Roambuilt states it adds 3" over the factory bumper |
What’s in the box
Bumper and sensor housings
LoPro front bumper with machined housings for the factory sensors.
Installation at a glance
Bolts directly to the frame and uses frame extensions.
The product page describes factory-bumper cutting and preparation; vehicle-specific bracket, drilling and retained-part requirements are listed in Fitment.
FAQ procedure when eliminating factory fog lamps
- With the vehicle off and battery disconnected, remove the factory bumper and leave the fog lamps hanging from the harness.
- Cut the wiring harness just behind the factory fog-lamp plug, remove the protective tape and bare the two wire ends.
- Connect a 50w 5ohm resistor between the two leads; the FAQ prefers soldering but also describes terminal connectors or matching-rating resistors with leads and crimp-style wire taps.
- Secure the resistor inside the replacement bumper with 3M VHB double-sided adhesive, out of the weather and away from other wiring because it gets hot.
- Once the remaining sensors are installed, turn on the ignition so the running lights come on and check that no fog-lamp warning remains.
Lead Time
Flat-rate shipping to the lower 48; large residential deliveries add a $200 lift-gate fee; international shipping is sometimes possible by special request.
This product
Roambuilt’s product page lists free commercial delivery with a loading dock or forklift; residential addresses and commercial addresses without either incur a lift-gate fee.
Warranty
Lifetime structural coverage for the original purchaser; powder coat covered for 60 days.
Read Roambuilt warranty policy on WNDR BuiltReturns
Returns within 30 days after delivery; 30% restocking fee and inspection apply.
Read Roambuilt returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon