
Leitner Designs
ACS ROOF for FORD TRANSIT 148 | 2015+
Indexed listing. WNDR Built doesn't sell this product; the button opens leitnerdesigns.com.
A roof platform with movable load bars
The Leitner Designs ACS ROOF is an aluminum platform rack for carrying gear above a Ford Transit. Its load bars slide along the side rails and secure through toothed clamp plates, letting you change their positions to suit the gear you carry.
The platform can grow beyond its supplied load bars: additional bars can be bought and installed later to create an almost fully flat platform. The rack uses a frame assembled in two sections, with front and rear mounting brackets attaching it to the van’s roof mounting points. This gives the system a configurable layout rather than requiring the load bars to stay at fixed spacing.
T-track accessory mounts
Leitner lists compatibility with T-track accessories from Thule, Rhino-Rack and Yakima.
Side-opening storage option
The rack pairs with the GearPOD ROOF, a side-opening, water-resistant, locking storage box.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Leitner Designs
- 2014-up Ford Transit · 148WB · Mid roof or high roof, as listed in Leitner’s installation guide.
Choose your roof height
The maker offers these two Transit 148 options.
TRANSIT 148 HIGH Roof
- For the Transit 148 high roof.
TRANSIT 148 MID Roof
- For the Transit 148 mid roof.
Mounting-hole clearance
Check that every M8x25 mounting bolt can thread into its roof mounting hole. If sheet metal interferes because the holes do not align, the guide requires making clearance with a Dremel or sheet-metal shears.
Roof load limits
The lower of the rack’s maximum and the vehicle manufacturer’s maximum roof load always applies. Vehicle roof load includes the rack, fitted accessories and cargo.
Loaded driving
The guide warns that a loaded roof rack raises the center of gravity and increases susceptibility to sway, instability and rollover. Distribute cargo evenly, keep it low and centered, secure it tightly and slow down for turns; high-speed off-road driving can damage the rack, accessories and vehicle even with a light load.
Secure cargo before travel
Check that fasteners, straps and locks are tightened and locked before every trip, inspect them periodically for wear, corrosion and fatigue, and check the load at stops. Never drive with a lock, knob or rack open or unlocked. Long loads must be tied down at the front and rear to the bumpers or tow hooks.
Cargo clearance and use
Check local and state laws for loads projecting beyond the vehicle, allow for cargo height and width at low clearances, obey posted speed limits and adapt speed to the road and load. Use the rack and accessories only for their intended purposes and do not exceed capacity.
Roof attachment
The product page lists compatibility both with and without a factory rail system. Before installation, check that the mounting rails match your vehicle length and roof height; the guide covers six Transit configurations.
Recommended equipment
Use only recommended racks and accessories, and check Leitner’s current Fit Guide when obtaining a new vehicle.
Specs, parts & installation
Frame and construction
| Material | Aluminum Alloy |
|---|---|
| Wall thickness | 1.5mm to 3.0mm multi-wall aluminum |
| Weight | 100 lbs. |
| Overall height | 4 inches, as listed on the product page |
| Fasteners | Grade 10.9 Black Zi-Ni Coated Fasteners |
| Bracket finish | The product page describes the steel brackets as “Zinc plated and power coated”. |
| Origin | Designed, engineered, and manufactured in the USA |
Load limits from the installation guide
| Off-road | Leitner’s guide states 250# off road. |
|---|---|
| On-road | Leitner’s guide states 500# on road. |
| Static | Leitner’s guide states 1000# static. |
What’s in the box
Rack assembly
Front and rear bars, side bars, load bars, endcaps with plastic retainers, front and rear mounting brackets, and a wind deflector; the product page lists a wind noise reducer as included.
Clamps and joining hardware
The guide’s Transit 148 mid/high roof hardware table lists 22 clamp plates, 44 single T-nuts, two long T-nuts and four set screws.
Fasteners
The same hardware table lists 47 M8 x 14 bolts, eight M6 x 12 fasteners, ten M8 T-bolts, three Traklok nuts and eight M8 x 25 bolts; M8 locknuts are also listed.
Installation at a glance
Leitner’s guide lists 2–3 hours, novice skill level and basic knowledge of hand tools.
Tall ladders are required; Leitner recommends a professional installation shop with suitable equipment and a friend to help.
Remove the tape covering the roof mounting holes, check bolt clearance and apply silicone or RV lap sealant at the bracket mounting areas. Install all four brackets with their flanges facing inward.
Assemble the frame in two sections, lift them onto the roof and join the side bars; install the load bars last. Seal the roof-mounting bolts with silicone or lap sealant. Follow the linked guide’s diagrams and tightening instructions.
Tools listed in the guide
- Torque wrench
- T30 and T40 Torx bit sockets
- 4mm Allen wrench
- 13mm socket
- 13mm and 12mm ratchet wrenches
- Silicone or RV lap sealant
Frame assembly details
- Work on carpet or blankets to avoid scratching parts. Square the corners, engage the clamp teeth with the extrusion grooves and tighten corner bolts to 16 ft-lb with a T40 Torx wrench.
- Fit the plastic retainers into the corner caps; secure each cap with two M6 x 12 fasteners and tighten to 24 in-lb with a T30 Torx wrench.
- Fit the wind deflector facing forward. Its Traklok nuts must rotate fully into place and tighten under the extrusion lip, as shown in the guide.
- Join each side-bar pair with one long T-nut centered at the joint and two set screws; tighten the set screws to the guide’s 3FTLBS specification.
- Fit two clamp plates per load bar, teeth facing outward, and rotate the bars into the side extrusions. The guide gives optional even spacing of 10.75” for the 148WB mid roof and 9.75” for the 148WB high roof.
Lock care, if using locking accessories
- The guide says to turn and move locks periodically and use graphite or dry lubricant. Locks deter theft but are not theft-proof; remove valuable gear when leaving the vehicle unattended for an extended period and keep at least one key in the glove compartment.
Source notes
- Leitner’s product page lists 1,000 lbs static, 600 lbs on-road and 300 lbs off-road; its installation guide, page 25, states 250# off road, 500# on road and 1000# static. This listing follows the guide.
- Leitner’s product title and description say 2015+; its installation guide cover says 2014-up Ford Transit and the guide includes the 148WB mid/high roof models. This listing follows the guide.
- Leitner’s product page says no-drill bolt-on mounting with no permanent modification; its guide, page 9, requires trimming sheet metal if misaligned roof holes prevent the mounting bolts from threading. This listing follows the guide.
- The guide’s 148WB mid/high roof hardware table on page 5 lists ten M8 locknuts, while page 21 instructs tightening eight M8 locknuts. The disputed locknut count is omitted here.
Lead Time
Target dispatch: same or next business day; international destination coverage differs between pages; email Leitner for a shipping quote; customers pay international shipping and customs charges.
Read Leitner Designs lead time policy on WNDR BuiltWarranty
Two-year warranty for defects in materials and workmanship under normal use and proper maintenance; see the brand page for full terms.
Read Leitner Designs warranty policy on WNDR BuiltReturns
Returns within 30 days require sealed original packaging; 20% restocking fee and return shipping apply.
Read Leitner Designs returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon