
Flatline Van Co.
Transit Side Steps
Indexed listing. WNDR Built doesn't sell this product; the button opens flatlinevanco.com.
Side-door access on dimpled steel steps
Flatline Van Co. lists steel side steps for Ford Transit vans that mount in the factory step location. The passenger-side step provides a platform at both the front door and the sliding door, while the driver-side step serves the front door.
Square and round steel tubing form the steps, with formed, dimpled tread plates that Flatline describes as providing traction and letting the elements fall through. The steps sit close to the van body to preserve ground clearance, with a powder coat finish and corrosion-resistant hardware.
Door coverage
Passenger side step covers both the front door and the sliding door
Steel construction
Steel tube construction with dimpled tread plates and powder coat finish
Body-hugging position
Sits tight to the van body to leave ground clearance; leaves room for larger tires and mud flaps
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Flatline Van Co.
- 2015+ Ford Transit 150/250/350 · 148"/148" EXT · Mid/High Roof
Drilling, rivet nuts and tapping
The guide calls for drilling 17/32” holes for rivet nuts at the driver-side brackets and rear brackets. Additional holes may be needed where factory mounting points differ. Factory studs and threaded inserts may need cleaning; unthreaded inserts require tapping. A pre-existing hole without an insert requires a rivet nut; a location without a hole or stud requires drilling and a rivet nut.
California Proposition 65
Flatline warns that this product can expose you to Carbon Black & Titanium Dioxide, known to the State of California to cause cancer.
Ladder compatibility
Directly compatible with the Transit Side Ladder - High Roof and Transit Side Ladder - Mid Roof without any modifications.
Factory mounting locations
Mounts in the factory step location using factory studs and threaded holes wherever possible
Installer requirement
Flatline recommends professional installation. If you have no mechanical experience and are not thoroughly familiar with the installation procedures, the guide requires a professional installer or other qualified person.
Before use
The guide requires proper assembly and secure attachment, checking mounting points and attachments before use, and regular inspection for wear or damage.
Specs, parts & installation
Construction
| Material | Square and round steel tube; dimpled tread plates; powder coat finish; corrosion-resistant hardware |
|---|---|
| Driver side step width | 35 inches |
What’s in the box
Step assemblies
One driver step front, one driver step rear, one passenger step front and one passenger step rear; two bayonets and two joining brackets.
Mounting brackets and spacers
Five step brackets, one driver front step bracket, two rear step brackets, six double bracket spacers and two single bracket spacers.
Listed hardware
The guide’s hardware page lists M8-1.25 x 25 flanged hex head screws, M8-1.25 nylon insert locknuts, M8 flat washers, M8-1.25 heavy duty rivet nuts, 1/4 flat washers, 1/4-20 x 0.75 flanged button head hex drive screws, 1/4-20 nylon insert locknuts and an M8-1.25 tap.
Installation at a glance
Flatline estimates 2 HRS and suggests additional help for a few installation steps.
Assemble both steps, prepare the factory mounting locations and install the brackets and rivet nuts as directed in the guide. Use blue thread lock where specified.
Lift the assembled steps onto the brackets with a helper or floor jack, fit the spacers, then install the rear brackets and passenger-side connecting plate. The guide directs a final check that all bolts and screws are tightened to 20ft-lbs.
Tools listed by Flatline
- Power drill; 3/16 drill bit; 17/32 drill bit.
- 7/32 Allen key; 5/32 Allen key; 13MM socket; 7/16 wrench; ratchet.
- Rivet nut tool with M8X1.25 mandrel; blue Loctite.
Mount preparation
- The guide recommends a wire brush with heat gun or an M8x1.25 die to clean undercoating from factory studs.
- Use the supplied M8x1.25 tap to clean threaded holes or tap unthreaded holes; Flatline recommends lubricant, preferably cutting oil.
- A pneumatic or electric drill-adapter rivet nut tool is recommended; a manual rivet nut tool can work if ground clearance allows.
Source notes
- Flatline’s product page says all required mounting hardware is included; its installation guide’s Hardware page omits the 3/8-16 x 1 serrated flanged hex head screws called for in Step 1. The contents above follow the guide’s hardware list without asserting a quantity for those screws.
Lead Time
In-stock dispatch: 1–2 business days; LTL delivery: typically 7–21 business days; preferred service uses flat rates; economy may be free with longer lead times.
Read Flatline Van Co. lead time policy on WNDR BuiltWarranty
Flatline-made products have a one-year limited warranty for the original purchaser; purchaser-paid claim returns and exclusions apply; other manufacturers’ products carry only their applicable manufacturer warranties.
Read Flatline Van Co. warranty policy on WNDR BuiltReturns
Returns within 30 days of receipt require RMA, unused original-packaged items and 20% restocking; customer-paid shipping unless Flatline error; clearance/garage-sale/final-sale excluded; identified custom/made-to-order exclusions may apply.
Read Flatline Van Co. returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon