
The BugWall
Winnebago Travato Ram Promaster Sliding Door Insect Bug Screen
Indexed listing. WNDR Built doesn't sell this product; the button opens thebugwall.com.
A roll-up replacement for the Travato sliding screen
The BugWall lists a side sliding door insect screen made as a replacement for the factory sliding screen in the Winnebago Travato and similar Class B RVs built on the Ram Promaster.
Zippers on both sides let the screen roll up; rolled flaps are secured with built-in buckle straps. Zipper across the top lets you remove the rolled-up screen for seasons when insect protection is not required (listed as new for Bug Wall V2).
Weighted lower edge
Foam along the bottom adds weight for a better roll-up (listed as new for Bug Wall V2).
Screen materials
No-See-Um bug netting on marine canvas.
Closure
Closure choice: magnetic closure for walking in and out, or a zipper in the center.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by The BugWall
Winnebago Travato or similar Class B RVs built on the RAM Promaster High roof · Side sliding door
Choose your Travato model
The model determines the opening location.
CENTER- Travato K Model
- For Travato K: the magnet opening is in the center, allowing access to the grab handle on the airline table in the doorway.
Opening closer to REAR of Van- Travato G Model
- For Travato G: the magnet opening sits closer to the rear so the screen opens to its highest point where your head is when entering and exiting.
Choose your opening type
Both opening types are offered with either model/location option.
Magnet
- Magnetic closure for walking in and out.
Zipper
- The description calls this a zipper in the center.
Trim before closing the sliding door
The installation guide says not to shut the sliding door with excess screen material untrimmed, because it could get caught.
Magnetic-screen tension
Too much side-to-side tension prevents the magnet strip from operating correctly; do not install a magnetic-closing screen too tight.
Weather-seal clearance
Leave enough fabric behind the flange and upper corners for the weather seal to seat fully. Pinch the weather seal shut before reinstalling it.
Trapped weather seal
For Travatos or other vans with an inaccessible weather seal, follow the trapped-seal video and any supplied bar-installation instructions. The guide says a couple of bars are supplied if the maker knew the van was a Travato or Sequence.
Promaster lower-front trim
If removing the plastic piece over the lower forward weather seal, leave extra fabric slack for reinstallation. Alternatively, loosen its 2 screws, tuck the screen behind it and retighten.
Roof height
High (Most Class B RVs) is the only roof-height option.
Separate rear screen
A rear screen specific to Travato models is sold separately.
Specs, parts & installation
Materials & manufacture
| Materials | US made marine canvas with No-See-Um bug netting and USA made marine grade zippers. The BugWall states the screen is UV stable. |
|---|---|
| Manufacture | The BugWall states it manufactures its screens in Conway, SC. |
What’s in the box
Screen & roll-up straps
Insect screen with built-in buckle straps for securing rolled-up flaps.
Installation supplies
Roll of double-sided tape and clips supplied with the screen, as described in the brand-wide installation guide.
Package extra
Bugwall coozie (the installation guide says one was included in the package).
Conditional trapped-seal hardware
The guide says a couple of bars and installation instructions are included when the maker was aware the van was a Travato or Sequence.
Installation at a glance
Installs around the side door-opening flange with double-sided tape and clips beneath the weather seal.
Check left/right position and length: the left zipper must not interfere with the weather seal on the left side. At the top, center the screen between the weather-seal bump-out and the right door edge, rather than the entire opening. Align the side-screen guideline with the flange edge so the bottom hangs in front of the step/floor; do not position it lower. Raise it above the guideline if you want it at or just above floor level.
Follow the updated written guide; the older videos are visual guides, and any supplemental instructions supplied with the screen also apply.
Installation sequence from the brand-wide guide
- Mark the weather seal and van so the seal can return to the same left-to-right position; remove the seal across the top and clean the flange with alcohol or water.
- Apply the double-sided tape across the top and around both corners, starting and ending just below the corners, ideally with half on each side of the flange; remove the red cover.
- Press the screen fabric onto the tape on the front and back of the flange, leaving room behind it for the seal.
- Use the thick supplied clips across the top. Start with one in the center and one toward each side, check the length before adding more because clips are difficult to remove, then place a clip about every 6-8" across the top.
- Wrap the fabric around the corners and down the sides, using clips suited to the metal thickness. Relief cuts in the screen material may help it follow the left-side bump-out; keep the zippers straight.
- After confirming placement, trim excess fabric. The guide recommends scissors; a razor is an alternative but is more likely to scratch the van.
- Pinch the weather seal shut, reinstall it using the reference mark, and use a mallet to seat it fully, especially in the corners.
Screens without a guideline
- For an older or rare model without a guideline, initially hang it about an inch too long; wrapping fabric behind the flange, installing clips and reinstalling the seal raises it about an inch.
Tools and supplies named in the guide
- Marker; alcohol or water for cleaning; a small hammer or mallet for the clips and seal; scissors (recommended) or a razor for trimming.
Lead Time
Lead times vary; contact the maker. Product banner: about 1 week to shipment for new orders; international taxes, fees, duties and tariffs are the buyer’s responsibility.
This product
The maker's product-page banner estimates 1 week until shipment from the shop for new orders due to high demand.
Warranty
Read The BugWall warranty policy on WNDR BuiltReturns
Returns within 30 days; later returns incur a 25% fee and are not accepted after 90 days.
Read The BugWall returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon