
The BugWall
Ford Transit Rear Garage Insect Screen
Indexed listing. WNDR Built doesn't sell this product; the button opens thebugwall.com.
Screen above the bed, covered storage below
This Ford Transit rear garage screen separates the open rear doorway into a screened sleeping area and a covered garage area. Netting starts at the bed, while insulated marine canvas covers the space below the platform. The BugWall describes that lower canvas as highly water resistant.
A clear-vinyl weather flap zips down over the upper section to protect the bed from rain or snow when you access gear below. The maker also says the zipped-down flap helps retain heat or air conditioning, and describes the Garage V2 as a four-season screen.
Lower garage access
The lower garage sections fold up and buckle at bed-platform height.
Center access
A full-height center zipper allows walking in and out; it also opens from the top for exiting the bed.
Privacy and removal
An interior privacy shade is included, and a zipper across the top lets you remove the garage screen.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by The BugWall
Ford Transit rear garage opening; roof options High, Mid or Low.
Choose the measuring method
The maker’s two product-page diagrams show different reference points for the bed layout. Both start at the rear-door latch hoop.
Method 1: top of mattress
- Measure from the latch hoop to the top of your mattress and select that measurement in Distance Down.
- The folded black garage section ends approx 7-8" below this measurement.
Method 2: bottom of bed platform
- Use this method when you do not want the garage folds below the bed frame, including where handlebars or similar gear have close clearance underneath.
- Measure from the latch hoop to the bottom of the bed platform, subtract 7", then select that result in Distance Down.
Fabric trimming required
Installation involves trimming excess screen material after the screen is positioned.
Custom bed-height fit
The maker requires one measurement to make the screen to your bed height. Distance down to Bed Platform options are 23 through 50; use the matching measuring method below.
Specs, parts & installation
Garage V2 construction
| Upper section | Screen from the bed up; No-See-Um bug netting |
|---|---|
| Lower section | Insulated marine canvas from the bed platform down; described by The BugWall as highly water resistant |
| Upper weather flap | Marine clear vinyl |
| Access | Full-height center zipper; center zipper also opens from the top |
| Removal | Top zipper |
What’s in the box
Garage screen
Custom bed-height garage screen with lower fold-up sections, upper clear-vinyl weather flap and interior privacy shade.
Installation supplies
Double-sided tape, retaining clips and a BugWall coozie, as stated in the maker’s installation guide.
Installation at a glance
Mount the screen around the doorway flange with double-sided tape and retaining clips, then reinstall the weather seal.
Follow the updated written instructions; older videos are a visual guide only, and any supplied supplemental instructions also apply. Pinch the weather seal closed before reinstalling it, then check that it is fully seated, especially at the corners.
If the weather seal is trapped behind another part, follow the trapped-seal guidance in the linked installation instructions.
For rear screens, align the latch holes, slots or cuts with the rear-door latches to set the screen height.
If the Transit plastic step can be removed, the maker recommends removing it to reach the weather seal; if the step is blocked in, follow the video for that area.
Installation sequence
- Mark the weather seal’s original position before removing it; clean the doorway flange with alcohol or water.
- Apply double-sided tape across the top and around both upper corners, folded half onto each side of the flange.
- Check the screen’s side-to-side position and length before fitting clips; leave fabric room behind the corners so the weather seal can seat fully.
- For Transit and ProMaster rear screens, use thick clips across the top: fit a few first, check length, then add clips about every 6-8".
- Wrap the fabric around the side flanges and choose retaining clips to suit the metal thickness; relief cuts can help the fabric follow the left-side bump-out. Keep the zippers straight.
- Once satisfied with the placement, trim the excess fabric; the maker recommends scissors.
- Pinch the seal closed, reinstall it in its marked position and use a mallet to ensure it is seated around the opening.
Tools and supplies mentioned by the maker
- Marker; alcohol or water for cleaning.
- Small hammer or mallet for seating clips and the weather seal.
- Scissors for trimming; the maker also mentions a razor but recommends scissors.
Lead Time
Lead times vary; contact the maker. Product banner: about 1 week to shipment for new orders; international taxes, fees, duties and tariffs are the buyer’s responsibility.
This product
The maker’s product-page banner currently estimates 1 week until shipment from its shop for new orders.
Warranty
Read The BugWall warranty policy on WNDR BuiltReturns
Returns within 30 days; later returns incur a 25% fee and are not accepted after 90 days.
This product
The maker’s product page says this screen is custom made to your bed height; its refund policy excludes custom products from returns.
What are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon