
Sandy Vans
Sprinter Van Slider Door Bug Screen 2007+
Indexed listing. WNDR Built doesn't sell this product; the button opens sandyvans.com.
A roll-up bug barrier for the slider opening
This slider screen uses transparent micro-mesh to keep an insect barrier across the open doorway while preserving the view outside. Sandy Vans says the mesh blocks gnats and mosquitoes. A magnetic seam provides pass-through access, with its position chosen to suit how you enter and leave the van.
Metal clips capture the screen beneath the factory weather seal rather than relying on magnets against the bodywork. The screen stays mounted between stops and rolls up with buckles when the doorway needs to be clear. The current version adds a localized Velcro patch at the handle location rather than a full-length Velcro edge.
Same mesh and hardware
Side Magnet and Middle Magnet use the same micro-mesh and include identical hardware; the difference is the seam position.
Two clip sizes
Thinner clips fit single-layer frame metal; wider clips fit two-layer sections.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Sandy Vans
Mercedes-Benz Sprinter 2007+ High Roof, slider door.
Choose your magnetic seam
Both options have the same mesh and hardware.
Side Magnet
- Closure at the edge of the opening; one large panel swings clear.
- The maker recommends this when a counter, fridge or cabinet occupies one side; place the seam on the open side.
Middle Magnet
- Closure in the center; the screen parts like curtains.
- The maker suggests this when the slider opens into clear floor space.
High Roof Sprinter only
Not compatible with Low Roof Sprinter models or non-Sprinter vans.
Access and trimming required
The clips need access to the metal lip beneath the factory weather seal; check whether finished interior panels cover it. Installation requires cutting excess mesh flush behind the clips. Mesh extending past the weather seal can wick water into the van.
Cannot zip off completely
Sandy Vans’ FAQ says the screens have no zipper across the top: they roll up and buckle in place, but full removal requires uninstalling them.
Sprinter-platform builds
Sandy Vans also lists these Sprinter-platform RV and upfitter builds: Winnebago Revel; Storyteller Overland (MODE, Beast Mode); Outside Van; Airstream Interstate & Atlas; Grech RV (Strada, Turismo, Terreno); Pleasure-Way Plateau; Leisure Travel Vans (Unity, Wonder); Coachmen Galleria; Midwest Automotive Designs; Jayco Terrain; Tiffin Wayfarer; Thor Tranquility. The maker says fitment depends on the exact model, year, suspension lift and body kit, and requires confirmation with its team before ordering.
Door handle adaptation
The product page lists both older standard handles and the 2025+ electric latch or electric assist door. For the electric handle, install the supplied Velcro patch at the handle location before mounting the screen so it seals around the latch and pulls free as the door opens. Older standard-handle Sprinters (2007–2024) skip the patch.
Specs, parts & installation
Screen construction
| Screen dimensions | 64" × 78" (before cutting) |
|---|---|
| Material | Transparent micro-mesh |
| Closure | Magnetic; Side Magnet or Middle Magnet |
What’s in the box
Screen and handle patch
1× Sliding Door Bug Screen (64" × 78") and 1× Velcro Patch for door handle compatibility.
Mounting items
4× Clamps and 25× Metal Clips in two sizes. The installation unboxing step also lists pry tools.
Installation at a glance
Sandy Vans lists 2 to 3 hours. The product page says no drilling or permanent van modifications are needed; the screen is trimmed to fit.
Metal clips secure the screen to the metal flange under the factory weather seal. Leave slack for the magnets to meet and keep the bottom about 1 inch above the fiberglass factory step.
Sandy Vans offers paid installation at its San Diego facility.
Installation sequence
- Pull the weather seal off the top and sides of the slider opening; the bottom can stay on.
- Hang the screen with the Sandy Vans logo facing out and clamp the two top corners.
- Keep the bottom about 1 inch above the fiberglass factory step, level side to side, with slack on both sides for the magnets to meet.
- Clip the top about every 4 to 6 inches, with three clips around each curved corner; then clip down the sides, keeping slack in the middle.
- Add extra wide clips at the corners and front edge. Use thinner clips for single-layer frame metal and wider clips for two-layer sections.
- Open and close the door to check that the magnets meet. Trim excess screen right behind the clips.
- Reinstall the weather seal from the bottom up, pulling it straight and tapping it in with the rubber mallet.
Tools listed by Sandy Vans
- Scissors
- Rubber mallet
- Clamps (included)
- Small step ladder
Lead Time
Shipping typically takes 5–7 business days; free shipping on Sandy Vans-fulfilled products.
Read Sandy Vans lead time policy on WNDR BuiltWarranty
Direct-fulfilled products cover material or workmanship defects under normal use; partner products follow the manufacturer’s warranty.
Read Sandy Vans warranty policy on WNDR BuiltReturns
Direct-fulfilled items: 30 days from delivery, uninstalled and undamaged; 20% restocking fee and customer-paid return shipping.
Read Sandy Vans returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon