
Unaka Gear Co.
Ford Transit Roof Rack - Premium - 148" Medium Roof
Indexed listing. WNDR Built doesn't sell this product; the button opens unakagearco.com.
An adjustable roof layout behind aluminum side plates
Unaka’s Premium rack uses an 8020 frame to carry crossbars for solar panels, lights and roof gear. Laser-cut aluminum side plates cover the side rails, while a single-piece welded aluminum wind fairing forms the front of the rack; Unaka says the fairing reduces wind noise.
Four adjustable solar crossbars let the installer position panels along the rack rather than fixing them in one front-to-back location. A separate rear 8020 crossbar provides another mounting point. Compared with Unaka’s Standard rack, this version uses a welded aluminum fairing rather than acrylic and a black powder-coated finish rather than black anodizing.
Pre-measured double T-nuts
Double T-nuts are pre-measured for the rack assembly.
Prepared fasteners
Loctite is pre-applied to the bolts that require threadlocker.
Accessory drop slots
Drop slots in the 8020 rails allow later accessory additions without taking the rack apart.
Internal channel splices
Internal splice plates connect the rail sections within the channel.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Unaka Gear Co.
2015+ Ford Transit 148 Medium Roof.
No light-bar capability
Unaka lists light-bar capability as “No” for this rack.
Roof preparation and inside access
Remove only the indicated rack-mount hole covers. Misaligned roof openings require trimming with tin snips and smoothing the edges; do not force an M8 bolt into a misaligned or paint-blocked insert. The guide calls for an M8 × 1.25 hand tap if paint prevents threading, and bonded washers and nylock nuts fitted from inside the van at rear mounts without threaded inserts.
Solar installation order
Rich Solar 250W panels cannot be installed after the exterior side plates. For panels 58.7 in or wider, including Rich Solar 250W, Unaka recommends placing the panels before the fan or air conditioner; the guide explicitly says this early positioning is not required for Rich Solar 200W panels.
Panel holes and installation supplies
If solar-panel flange holes do not match the crossbars, the guide requires new holes: place a board behind the flange, drill a 1/8 in pilot and finish with a 5/16 in bit. Dicor sealant and anti-seize are not included; the guide requires sealing roof brackets and applying anti-seize to wind-fairing bolts.
2026 antenna
Unaka states that the rack is compatible with the new 2026 Transit antenna location.
Solar layout
The product page lists mounting for two 200W solar panels up to 60.6 in wide. The manual also covers Rich Solar 250W panels, described there as 60.6 in long.
Existing fan or air conditioner
With rooftop equipment already installed, separately sold roll-in T-nuts can make panel mounting easier; the guide says a 250W panel between two immovable fans or other accessories is harder to install without them.
Solar-panel spacers
For 1.2 in thick panels, use one 1/4 in spacer plus one 1/8 in spacer at each mounting point; for 1.4 in thick panels, use one 1/4 in spacer at each point.
Torque checks
Unaka requires torque checks after 4–7 days, after one month, every 3–4 months thereafter, and after moderate driving on bumpy or gravel roads.
Unaka installation service
For installation at Unaka’s Greenville location, its Find a Builder page requires the OEM pre-threaded holes to be available.
Specs, parts & installation
Frame & exterior
| Foundation | 15-series 8020 aluminum |
|---|---|
| Shell | Laser-cut aluminum |
| Finish | Black powder coat |
| Wind fairing | Single-piece welded aluminum |
| Maker-listed rack weight | 75 lb |
| Maker-listed added height | 4 in |
Crossbars
| Solar crossbars | Four L-shaped aluminum crossbars; adjustable |
|---|---|
| Rear crossbar | One 15-series 8020 crossbar |
What’s in the box
Rack & fairing
Roof rack, aluminum wind fairing, side plates and rail splice plates.
Crossbars & solar hardware
Four L-shaped aluminum solar crossbars and mounting hardware for two 200W panels, plus one rear 15-series 8020 crossbar. The manual also lists 1/4 in and 1/8 in solar-panel spacers.
Mounting hardware & tools
All brackets and stainless steel hardware, plus a 3/16 in T-handle Allen wrench, a 1/8 in Allen wrench and a 5/32 in Allen wrench.
Installation at a glance
Unaka’s product page estimates about two hours; the manual requires two people with two ladders on level ground, and two-person handling of the unopened box.
Unaka recommends qualified-professional installation or following its detailed instructions. Assemble and position brackets, rails and crossbars with hardware loose where instructed, then square the rack before the specified tightening and sealing steps.
Seal the roof brackets, their bolts and sealing washers with Dicor according to its instructions. Complete the solar, side-plate and fairing sequence in the matched guide, then check all hardware for correct torque.
When fitting the wind fairing, take extra precautions not to drop it onto the windshield or down the front of the van.
Assembly and tightening sequence
- Identify all parts and keep similar but non-interchangeable hardware separate. Install T-nuts long side first and boss down, keeping loose hardware secure enough not to fall off.
- Join rail sections with internal splice plates halfway into each section and torque their set-screw hardware to 15 in-lb. Keep roof-bracket attachment hardware loose at this stage.
- Set front rails to the same fore-and-aft position; the guide gives 10.75 in from the first bracket’s leading edge as an adjustable target. Use front, middle and rear crossbars to set rail spacing.
- Once parallel, square and centered, the guide specifies 132 in-lb for the adapter/side-rail roof attachment step. Check bracket button-head screws before panels make access difficult.
- The guide specifies 75.2 in-lb for solar-panel spacer hardware and 132 in-lb for side-plate and wind-fairing hardware; follow the matched manual’s connection-specific values.
- For Rich Solar 250W panels, locate the mounting hardware under the crossbar’s outside slots before lowering the crossbar over it; the manual says to skip this for smaller panels. Leave solar connectors accessible before bolting panels in place.
- A 250W panel at the very front can block the lower fairing bolt. Keep front side plates loose and slide them forward to access and tighten that bolt, then return and secure the side plates.
- Check crossbar and splice-plate interference with the solar layout. The guide allows repositioning crossbars or omitting the side-rail splice plate if it interferes.
- Install rear end caps after the required T-nuts. Tighten self-tapping screws snugly without overtightening, then complete the final torque check.
Tools and consumables listed by Unaka
- Torque wrench covering 75–132 in-lb; 1/2 in and 7/16 in sockets, 13 mm socket, matching box wrenches and two ladders.
- Tin snips, file, tape measure, caulk gun, sandpaper and paint-cleaning/preparation materials; cap removal also uses a heat gun, plastic scraper and denatured alcohol.
- Dicor sealant and anti-seize are not supplied. Threadlocker is pre-applied to kit bolts requiring it; add Blue Loctite 242 where the guide calls for it if required.
Lead Time
Unaka’s Shipping Information excludes oversized items from free shipping, and its Shipping policy excludes items shipped by LTL freight.
This product
Unaka’s product page advertises free shipping on large Unaka products, including roof racks and ladders, to the Lower 48.
Warranty
Unaka-designed and fabricated parts have a defects warranty for the original purchaser during the product’s production lifetime; third-party kit components and wear parts are excluded, coatings have 180-day coverage, and modification or misuse voids the warranty.
Read Unaka Gear Co. warranty policy on WNDR BuiltReturns
The Refund policy’s Returns section requires an RMA, new condition, original packaging and freight-prepaid returns, with no refunds after 30 days from invoice and a minimum 10% fee if the customer covers shipping or 20% otherwise; its Terms & Conditions of Sale instead lists 15 days from receipt and a 15% fee. Custom, electronic, discontinued and specially priced items are excluded; the Sale terms also exclude opened or installed parts.
Read Unaka Gear Co. returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon