
The BugWall
03-06 T1N Mercedes Sprinter Sliding Door Insect Bug Screen
Indexed listing. WNDR Built doesn't sell this product; the button opens thebugwall.com.
Insect screening with an entry where you need it
This sliding-door screen keeps insects out while letting fresh air into the van. Marine canvas surrounds No-See-Um netting, with a magnetic or zippered opening for passing through.
The opening can sit in the center or closer to either end of the doorway to suit the route around your interior furniture. The BugWall says the offset opening lets the screen open to its highest point near where your head passes through.
Marine zippers
Marine-grade side zippers let the screen roll up; built-in buckle straps hold the rolled flaps.
Removable screen
The V2 top zipper lets you remove the rolled-up screen when insect protection is not needed.
Weighted bottom
Added foam along the bottom increases its weight and helps the screen roll up.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by The BugWall
2003-2006 T1N Mercedes Sprinter · High roof · Sliding side door
Choose the entry location
Choose the opening where you normally walk in and out; if cabinetry sends you toward the front, choose the front opening.
Center
- Opening in the center.
Opening closer to FRONT of Van
- Opening approx. 14" from the front edge of the door opening.
Opening closer to REAR of Van
- Opening approx. 14" from the rear edge of the door opening.
Choose the closure
The maker offers these opening types.
Magnet
- Magnetic closure for walking in and out.
Zipper
- A zippered opening instead of the magnetic closure.
Magnetic-screen tension
On Magnet versions, excessive side-to-side tension prevents the magnetic strip from operating correctly; do not install the screen too tight.
Fabric trimming required
Installation involves trimming excess screen material. On sliding doors, do not close the door before trimming: excess fabric could get caught.
Sliding-door clearance
Position the left zipper so it does not interfere with the left weather seal. Center the screen between the seal’s bump-out and the right doorway edge.
No T1N rear screen
The maker says rear screens are not available for this older T1N Sprinter.
Trapped weather seal
If the weather seal is trapped behind another part and cannot be removed, follow the trapped-seal guidance and any supplemental instructions in the maker’s installation guide.
Specs, parts & installation
Screen construction
| Fabric | US-made marine canvas |
|---|---|
| Netting | No-See-Um bug netting |
| Zippers | Marine-grade zippers on both sides and across the top |
| Bottom edge | Added foam for weight and roll-up |
What’s in the box
Screen
Door screen with built-in buckle straps and foam along the bottom.
Installation supplies
Double-sided tape, retaining clips and a BugWall coozie, as stated in the maker’s installation guide.
Installation at a glance
Mount the screen around the doorway flange with double-sided tape and retaining clips, then reinstall the weather seal.
Follow the updated written instructions; older videos are a visual guide only, and any supplied supplemental instructions also apply. Pinch the weather seal closed before reinstalling it, then check that it is fully seated, especially at the corners.
Use the side-screen guideline at the upper flange to set the bottom just past the step/floor; do not set it lower. Raise it if you want it at or just above the floor. Where a guideline is absent, initially hang the screen about an inch too long before wrapping and clipping.
Installation sequence
- Mark the weather seal’s original position before removing it; clean the doorway flange with alcohol or water.
- Apply double-sided tape across the top and around both upper corners, folded half onto each side of the flange.
- Check the screen’s side-to-side position and length before fitting clips; leave fabric room behind the corners so the weather seal can seat fully.
- For top clips, fit a few thick clips first, check the length, then add clips about every 6-8" across the top.
- Wrap the fabric around the side flanges and choose retaining clips to suit the metal thickness; relief cuts can help the fabric follow the left-side bump-out. Keep the zippers straight.
- Once satisfied with the placement, trim the excess fabric; the maker recommends scissors.
- Pinch the seal closed, reinstall it in its marked position and use a mallet to ensure it is seated around the opening.
Tools and supplies mentioned by the maker
- Marker; alcohol or water for cleaning.
- Small hammer or mallet for seating clips and the weather seal.
- Scissors for trimming; the maker also mentions a razor but recommends scissors.
Source notes
- The BugWall’s T1N product description says “Designed for high-roof models” and “Fits 2003-2006 Mercedes Sprinter Models High roof”; the same product’s Roof Height selector offers High and Low. This listing uses High-roof fitment; Low-roof fitment remains unconfirmed.
- The BugWall’s T1N description calls the magnetic or zipper closure centered, but its offset-option text places the magnet/zipper opening approx. 14" from the door-opening edge; the live selector offers Magnet and Zipper at Center, Opening closer to FRONT of Van and Opening closer to REAR of Van. The listed opening choices follow the selector and its specific offset description.
Lead Time
Lead times vary; contact the maker. Product banner: about 1 week to shipment for new orders; international taxes, fees, duties and tariffs are the buyer’s responsibility.
This product
The maker’s product-page banner currently estimates 1 week until shipment from its shop for new orders.
Warranty
Read The BugWall warranty policy on WNDR BuiltReturns
Returns within 30 days; later returns incur a 25% fee and are not accepted after 90 days.
Read The BugWall returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon