
REAR DOOR ACCESS LADDER FOR MERCEDES SPRINTER HIGH ROOF [H2]
Indexed listing. WNDR Built doesn't sell this product; the button opens primedesign.net.
Sprinter H2 rear-door access
Prime Design’s ladder puts climbing rungs on the van’s rear door. Upper door brackets hang over the door’s top edge, while lower hanger rods draw the lower brackets into place.
This listing is the clear-anodized aluminum version. Prime Design describes the anodized finish as protection against corrosion, scratching and fading, but notes that prolonged exposure to road contaminants without cleaning can break down the anodizing layer.
Rubber contact isolators
The upper brackets seat over the door edge on rubber isolators. The lower brackets are tightened until their rubber isolators begin to compress.
Lower hanger-rod adjustment
The lower mounting hanger rods arrive pre-assembled. Their tightening hardware is removed after installation and retained for future adjustments.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Prime Design
- Mercedes Sprinter · 2007+ · High Roof [H2]
Specified mounting position
Install only in the position shown in the matching assembly manual; Prime Design warns that a different position may compromise attachment. Use only OEM-supplied parts, including for repairs. Do not add rubber, plastic or other material between the door brackets and body unless supplied with the ladder.
Hand tools only
Do not use power tools to tighten fasteners. Overtightening the hanger-rod nuts may cause the brackets to damage the door skin.
Backup-camera clearance
The OEM backup camera may need relocation if the ladder is in its field of view.
Door must be latched
Before using the ladder, securely close and latch the door at the top and bottom. Do not drive with the rear door open or while someone is using the ladder.
Climbing requirements
- Face the ladder and maintain three-point contact at all times: two feet and one hand, or one foot and two hands.
- Keep both hands and arms free for climbing. Do not carry tools or equipment in hand; secure hand tools in a pouch holster, tool belt or otherwise, and use safe alternative methods for handling materials and supplies.
- Never jump from or slide down more than one rung or step at a time. Avoid climbing with greasy or slippery hands or gloves; keep the ladder and footwear free of oil, grease and slippery substances.
Weather and user limits
Avoid use during high winds or storms; clear ice, frost or snow from the ladder before use. Prime Design says users who are prone to fatigue, have physical limitations such as fainting, take medication that may impair them, or have another condition preventing safe climbing must not use the ladder.
Fastener and condition checks
- Check and retorque mounting fasteners after the first week of initial service, then monthly thereafter.
- Inspect rungs, side rails, mounting brackets, fasteners, rubber isolators and rivets for corrosion and deterioration every six (6) months, or more frequently as environmental exposure and conditions require; check the ladder’s position and readjust it if necessary.
- All mountings, fasteners and hardware must be intact and secure. Remove the ladder from service if any are missing, loose or damaged until corrected. Structural damage or defects that make it hazardous require removal from service and repair by a competent individual, or removal and/or destruction so it cannot be used.
- Keep OEM safety stickers, labels, decals, markings and information conspicuous on new, fixed or repaired ladders; replace missing safety labels only with OEM-approved labels. Keep records of annual or regularly scheduled inspections, maintenance and repairs.
Finish care
- Use mild soap and water for most soils; the manual permits automotive aluminum cleaners and polishes for stubborn contaminants.
- Do not use harsh chemical cleaners, aggressive alkaline or acid cleaners, or excessive abrasive rubbing. Do not use strong cleaners on surrounding glass or other components where they could contact the aluminum; immediately wash the ladder if contact occurs.
Specs, parts & installation
Construction
| Material | Aluminum |
|---|---|
| Finish | Clear anodized |
Maker-listed weight
| Weight | 18 kg |
|---|
What’s in the box
Ladder
One access ladder in the listed clear-anodized finish.
Mounting assemblies
One left/right upper mounting-bracket pair, one left/right bottom hanger-bracket pair, and one left/right lower mounting-bracket pair.
Fastening hardware
One hanger-bracket hardware kit: eight M8 x 20MM bolts, eight flat washers and eight lock washers.
Installation at a glance
Upper door brackets and lower hanger rods attach the ladder to the rear door.
Prime Design recommends positioning the van on ground as level as possible during installation.
Assemble the brackets and hanger rods, seat the upper brackets on the door edge, level the ladder, and tighten the mounts in the sequence specified in the matching assembly manual.
Tools listed in the assembly manual
- Torque wrench with 13MM socket
- Ratchet with 13MM socket
- 13MM combination wrench
- Torpedo level
- Tape measure
- Grease or wax pencil
Lead Time
Built-to-order racks typically take about two weeks to manufacture, partially assemble, and ship; actual lead time varies.
Read Prime Design lead time policy on WNDR BuiltWarranty
Read Prime Design warranty policy on WNDR BuiltReturns
Read Prime Design returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon