
Leitner Designs
ACS ROOF for MERCEDES BENZ SPRINTER 144 | 2007+
Indexed listing. WNDR Built doesn't sell this product; the button opens leitnerdesigns.com.
A roof platform with repositionable load bars
The Leitner Designs ACS ROOF carries gear above a Sprinter on an aluminum platform with adjustable load bars. The bars slide along toothed side channels, so their positions can change with the gear you carry rather than staying at fixed crossbar locations. Additional load bars can be installed later to build an almost fully flat platform.
The rack also provides mounting paths for accessories. Its T-track accepts accessories from Thule, Rhino-Rack and Yakima, while Leitner’s GearPOD ROOF pairs with the rack for side-opening, water-resistant, locking storage. An optional OWL SIDE ladder can be integrated on vans with factory roof rails.
Two-section frame
The frame assembles in two sections that join on the roof; load bars go on last to keep the sections manageable during installation.
Included wind deflector
A wind deflector mounts to the front of the rack using Traklok nuts.
Expandable platform
Extra load bars can be added without replacing the rack.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Leitner Designs
- Mercedes-Benz Sprinter 144 · 2007+ · High roof or low roof; select the matching roof-height option.
Choose your roof height
Match the option to your Sprinter 144 roof.
Sprinter 144 HIGH Roof
- For the high-roof Sprinter 144.
Sprinter 144 LOW Roof
- For the low-roof Sprinter 144.
Vehicle roof limit governs
The guide requires using the lower of the rack rating and the vehicle manufacturer’s maximum roof load. Vehicle roof load includes rack weight, fitted accessories and cargo.
OWL SIDE ladder integration
Optional OWL SIDE ladder integration requires factory roof rails.
Working at roof height
Tall ladders are required for the roof installation. Leitner recommends a professional shop with suitable equipment and a friend to help handle the large rack.
Loaded handling and long cargo
The guide warns that roof loads increase sway, instability and rollover risk. Distribute cargo evenly, keep it low and centered, secure it tightly and slow for turns. Tie long loads front and rear to vehicle bumpers or tow hooks.
Driving and clearance
Follow posted speed limits and adapt speed to conditions and load; high-speed off-road driving can damage the rack, accessories and vehicle even with a light load. Check cargo height, width and local projection laws; never drive with a lock, knob or rack open or unlocked.
California warning
Leitner’s product page carries a warning for cancer and reproductive harm: www.P65Warnings.ca.gov.
Roof mounting
Leitner lists compatibility both with and without factory roof rails. For installation without factory rails, call Leitner Designs at 949-395-3049. The linked guide describes installation into factory roof tracks.
Accessory fit
Leitner lists compatibility with T-track accessories from Thule, Rhino-Rack and Yakima, and with its GearPOD ROOF storage box.
Before every trip
Check that knobs, bolts, screws, straps and locks are attached, tightened and locked. Inspect periodically for wear, corrosion and fatigue, and check load security at stops.
Specs, parts & installation
Frame and construction
| Material | Aluminum Alloy |
|---|---|
| Wall thickness | 1.5mm to 3.0mm multi-wall aluminum |
| Weight | 100 lbs. |
| Overall height | 4 inches |
| Fasteners | Grade 10.9 Black Zi-Ni Coated Fasteners |
| Bracket finish | Zinc plated and powder coated steel brackets |
| Origin | Designed, engineered, and manufactured in the USA |
Load ratings
| Rack capacity | Leitner’s Sprinter 144 installation guide states 250# off road – 500# on road - 1000# static. The lower applicable vehicle roof limit always governs. |
|---|
What’s in the box
Rack structure
Side bars, front and back bars, load bars, mounting brackets and endcaps, as shown in the installation guide.
Wind deflector
Wind noise reducer, described as the wind deflector in the guide.
Assembly and mounting hardware
Single and long T-nuts, M8 T-bolts, M8 x 14 bolts, M6 x 12 fasteners, M8 locknuts, clamp plates, rail bolts, Traklok nuts and set screws.
Installation at a glance
Leitner’s guide lists 2–3 hours, novice skill level and basic hand-tool knowledge.
The rack bolts to the roof mounting system without drilling, as described on the product page; the guide shows the factory-track method. Assemble the frame on carpet or blankets in two sections, lift them to the roof, join the side bars and install load bars last.
On the high-roof Sprinter 144, the driver-side ladder cutout uses seven rail bolts, leaving one rail bolt and one M8 locknut over. Read the linked guide before installation.
Tools in the guide
- Torque wrench; T30 and T40 Torx bit sockets; 4mm Allen wrench; 13mm socket; 13mm ratchet wrench.
- A 13mm ratcheting wrench is needed for the underside mounting-bracket locknuts; the guide says a ratchet and socket will not fit.
Factory-track installation sequence
- Remove rubber track endcaps and slide the rail bolts into the factory mounting tracks. Position them above the studs attaching the roof rails, within 1” to either side as allowed in the guide.
- Fit four mounting brackets with flanges inward: short mounts at the rear and long mounts at the front.
- Assemble and square the frame sections. The side bar must contact the stop lip, and the front/back bar must fully contact the side bar. Align clamp teeth with the extrusion grooves.
- Fit endcaps and the forward-facing wind deflector. Ensure Traklok nuts rotate fully under the extrusion lip before tightening.
- Lift rear and front sections onto the mounting brackets, with the wind deflector above the windshield. Join side bars with a large T-nut centered at each joint and set screws.
- Set side bars 1/2” from the front edge of the mounting brackets, then tighten mounting locknuts.
- Rotate load bars into the side extrusions with two clamp plates per bar, teeth facing out. Reposition bars as needed.
Guide torque values
- Do not overtighten bolts. The guide lists all 8mm bolts at 16ft-lb and all 6mm bolts at 2ft-lb.
- The endcap step specifies 24 IN-LB; side-bar set screws are specified at 3FTLBS.
Lock care and use
- Move locks periodically and use graphite or dry lubricant. Locks deter theft but are not theft-proof; remove valuables when leaving the vehicle unattended for extended periods.
- Use only recommended racks and accessories, check the current Fit Guide when changing vehicles and do not use the carriers for unintended purposes or exceed capacity.
Source notes
- Leitner’s product page lists 1,000 lbs static, 600 lbs on-road and 300 lbs off-road; its Sprinter 144 installation guide (page 20) lists 250# off road, 500# on road and 1000# static. This listing follows the guide.
- The guide describes eight T-bolts for each frame section on page 15, but says to tighten eight mounting-bracket M8 locknuts on page 17; this listing omits the disputed total.
Lead Time
Target dispatch: same or next business day; international destination coverage differs between pages; email Leitner for a shipping quote; customers pay international shipping and customs charges.
Read Leitner Designs lead time policy on WNDR BuiltWarranty
Two-year warranty for defects in materials and workmanship under normal use and proper maintenance; see the brand page for full terms.
Read Leitner Designs warranty policy on WNDR BuiltReturns
Returns within 30 days require sealed original packaging; 20% restocking fee and return shipping apply.
Read Leitner Designs returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon